Region 4 Education Service Center (ESC)
Contract # R240901
for
HVAC Solutions, Related Products and Services
with
Daikin Applied
Effective: January 1, 2025
The following documents comprise the executed contract between the
Region 4 Education Service Center and Daikin Applied, effective January
1, 2025:
I. Vendor Contract and Signature Form
II. Supplier’s Response to the RFP, incorporated by reference
Contract
This Contract (“Contract”) is made as of January 1, 2025 by and between Daikin Applied
(“Contractor”) and Region 4 Education Service Center (“Region 4 ESC”) for the purchase of
HVAC Solutions, Related Products & Services (“the products and services”).
RECITALS
WHEREAS, Region 4 ESC issued Request for Proposals Number 24-09 for HVAC Solutions,
Related Products & Services (“RFP”), to which Contractor provided a response (“Proposal”);
and
WHEREAS, Region 4 ESC selected Contractor’s Proposal and wishes to engage Contractor
in providing the services/materials described in the RFP and Proposal;
WHEREAS, both parties agree and understand the following pages will constitute the
Contract between the Contractor and Region 4 ESC, having its principal place of business at
7145 West Tidwell Road, Houston, TX 77092.
WHEREAS, Contractor included, in writing, any required exceptions or deviations from
these terms, conditions, and specifications; and it is further understood that, if agreed to by
Region 4 ESC, said exceptions or deviations are incorporated into the Contract.
WHEREAS, this Contract consists of the provisions set forth below, including provisions of
all attachments referenced herein. In the event of a conflict between the provisions set forth
below and those contained in any attachment, the provisions set forth below shall control.
WHEREAS, the Contract will provide that any state and local governmental entities, public
and private primary, secondary and higher education entities, non-profit entities, and agencies
for the public benefit (“Public Agencies”) may purchase products and services at prices
indicated in the Contract upon the Public Agency’s registration with OMNIA Partners.
1) Term of agreement. The initial term of the Contract is for a period of three (3) years unless
terminated, canceled or extended as otherwise provided herein. Region 4 ESC shall have the
right in its sole discretion to renew the Contract for an additional term of up to two (2) years or
for a lesser period of time as determined by Region 4 ESC by providing written notice to the
Contractor of Region 4 ESC’s intent to renew thirty (30) days prior to the expiration of the
original term. Contractor acknowledges and understands Region 4 ESC is under no obligation
whatsoever to extend the term of this Contract. Notwithstanding the forgoing paragraph, the
term of the Contract, including any extension of the original term, shall be further extended
until the expiration of any Purchase Order issued under the Contract for a period of up to one
year beyond the Contract term.
2) Scope: Contractor shall perform all duties, responsibilities and obligations, set forth in this
agreement, and described in the RFP, incorporated herein by reference as though fully set
forth herein.
3) Form of Contract. The form of Contract shall be the RFP, the Offeror’s proposal and Best and
Final Offer(s).
CONTRACT
1
4) Order of Precedence. In the event of a conflict in the provisions of the Contract as accepted
by Region 4 ESC, the following order of precedence shall prevail:
i. This Contract
ii. Offeror’s Best and Final Offer
iii. Offeror’s proposal
iv. RFP and any addenda
5) Commencement of Work. The Contractor is cautioned not to commence any billable work or
provide any material or service under this Contract until Contractor receives a purchase order
for such work or is otherwise directed to do so in writing by Region 4 ESC.
6) Entire Agreement (Parol evidence). The Contract, as specified above, represents the final
written expression of agreement. All agreements are contained herein and no other
agreements or representations that materially alter it are acceptable.
7) Assignment of Contract. No assignment of Contract may be made without the prior written
approval of Region 4 ESC. Contractor is required to notify Region 4 ESC when any material
change in operations is made (i.e., bankruptcy, change of ownership, merger, etc.).
8) Novation. If Contractor sells or transfers all assets or the entire portion of the assets used to
perform this Contract, a successor in interest must guarantee to perform all obligations under
this Contract. Region 4 ESC reserves the right to accept or reject any new party. A change of
name agreement will not change the contractual obligations of Contractor.
9) Contract Alterations. No alterations to the terms of this Contract shall be valid or binding
unless authorized and signed by Region 4 ESC.
10) Adding Authorized Distributors/Dealers. Contractor is prohibited from authorizing additional
distributors or dealers, other than those identified at the time of submitting their proposal, to
sell under the Contract without notification and prior written approval from Region 4 ESC.
Contractor must notify Region 4 ESC each time it wishes to add an authorized distributor or
dealer. Purchase orders and payment can only be made to the Contractor unless otherwise
approved by Region 4 ESC. Pricing provided to members by added distributors or dealers
must also be less than or equal to the Contractor’s pricing.
11) TERMINATION OF CONTRACT
a) Cancellation for Non-Performance or Contractor Deficiency. Region 4 ESC may terminate
the Contract if purchase volume is determined to be low volume in any 12-month period.
Region 4 ESC reserves the right to cancel the whole or any part of this Contract due to
failure by Contractor to carry out any obligation, term or condition of the contract. Region
4 ESC may issue a written deficiency notice to Contractor for acting or failing to act in any
of the following:
i. Providing material that does not meet the specifications of the Contract;
ii. Providing work or material was not awarded under the Contract;
iii. Failing to adequately perform the services set forth in the scope of work and
specifications;
iv. Failing to complete required work or furnish required materials within a reasonable
amount of time;
CONTRACT
2
v. Failing to make progress in performance of the Contract or giving Region 4 ESC
reason to believe Contractor will not or cannot perform the requirements of the
Contract; or
vi. Performing work or providing services under the Contract prior to receiving an
authorized purchase order.
Upon receipt of a written deficiency notice, Contractor shall have a reasonable amount
of time to provide a satisfactory response to Region 4 ESC. Failure to adequately
address all issues of concern may result in Contract cancellation. Upon cancellation
under this paragraph, and upon payment for work and materials already performed or
furnished, all goods, materials, work, documents, data and reports prepared by
Contractor under the Contract shall immediately become the property of Region 4 ESC.
b) Reserved.
c) Delivery/Service Failures. Failure to deliver goods or services within a mutually agreed
time frame or failure to make repairs, replacements or corrections in accordance with
the applicable warranty (as defined below) shall constitute grounds for the Contract to
be terminated, subject to the provisions set forth in Section 11.a) providing for notice
to Contractor and Contractor's reasonable opportunity to cure any alleged unmet
performance obligation.
d) Force Majeure. If by reason of Force Majeure, either party hereto shall be rendered unable
wholly or in part to carry out its obligations under this Agreement then such party shall
give notice and full particulars of Force Majeure in writing to the other party within a
reasonable time after occurrence of the event or cause relied upon, and the obligation of
the party giving such notice, so far as it is affected by such Force Majeure, shall be
suspended during the continuance of the inability then claimed, except as hereinafter
provided, but for no longer period, and such party shall endeavor to remove or overcome
such inability with all reasonable dispatch.
The term Force Majeure as employed herein, shall mean acts of God, strikes, lockouts, or
other industrial disturbances, act of public enemy, orders of any kind of government of the
United States or the State of Texas or any civil or military authority; insurrections; riots;
epidemics; landslides; lighting; earthquake; fires; hurricanes; storms; floods; washouts;
droughts; arrests; restraint of government and people; civil disturbances; explosions,
breakage or accidents to machinery, pipelines or canals, or other causes not reasonably
within the control of the party claiming such inability. It is understood and agreed that the
settlement of strikes and lockouts shall be entirely within the discretion of the party having
the difficulty, and that the above requirement that any Force Majeure shall be remedied
with all reasonable dispatch shall not require the settlement of strikes and lockouts by
acceding to the demands of the opposing party or parties when such settlement is
unfavorable in the judgment of the party having the difficulty.
e) Standard Cancellation. Region 4 ESC may cancel this Contract in whole or in part by
providing written notice. The cancellation will take effect 30 business days after the other
party receives the notice of cancellation. After the 30th business day all work will cease
following completion of final purchase order. Any purchase order, service order or
agreement to procure goods and services already accepted by Contractor prior to such
termination shall continue through its fulfillment and payment, notwithstanding any
termination of this Contract
12) Licenses. Contractor shall maintain in current status all federal, state and local licenses, bonds
and permits required for the operation of the business conducted by Contractor. Contractor
shall remain fully informed of and in compliance with all ordinances and regulations pertaining
to the lawful provision of services under the Contract. Region 4 ESC reserves the right to stop
work and/or cancel the Contract if Contractor’s license(s) expire, lapse, are suspended or
terminated.
CONTRACT
3
13) Survival Clause. All applicable software license agreements, warranties or service
agreements that are entered into between Contractor and Region 4 ESC under the terms and
conditions of the Contract shall survive the expiration or termination of the Contract. All
Purchase Orders issued and accepted by Contractor shall survive expiration or termination of
the Contract for a period of up to one year beyond the term of the Contract.
14) Delivery. Conforming product shall be shipped within 7 days of receipt of Purchase Order or
as otherwise indicated by Contractor or the applicable manufacturer. If delivery is not or
cannot be made within this time period, the Contractor must receive authorization for
the delayed delivery. The order may be canceled if the estimated shipping time is not
acceptable. All deliveries shall be freight prepaid, F.O.B. first destination and shall be
included in all pricing offered unless otherwise clearly stated in writing.
15) Inspection & Acceptance. If defective or incorrect material is delivered, Region 4 ESC may
make the determination to return the material to the Contractor at no cost to Region 4 ESC
provided that before such return Region 4 ESC and contractor have mutually agreed on a
timeframe within which contractor may cure the alleged defect or incorrect delivery and
allow the contractor to effect such cure. The Contractor agrees to pay all shipping costs for
the return shipment. Contractor shall be responsible for arranging the return of the defective
or incorrect material.
16) Payments. Payment shall be made after satisfactory performance, in accordance with all
provisions thereof, and upon receipt of a properly completed invoice, but in no event later
than sixty (60) days from invoice date.
17) Price Adjustments. Should it become necessary or proper during the term of this Contract to
make any change in design or any alterations that will increase price, Region 4 ESC must be
notified immediately. Price increases must be approved by Region 4 ESC and no payment for
additional materials or services, beyond the amount stipulated in the Contract shall be paid
without prior approval. All price increases must be supported by manufacturer documentation,
or a formal cost justification letter. Contractor must honor previous prices for thirty (30) days
after approval and written notification from Region 4 ESC. It is the Contractor’s responsibility
to keep all pricing up to date and on file with Region 4 ESC. All price changes must be
provided to Region 4 ESC, using the same format as was provided and accepted in the
Contractor’s proposal.
Price reductions may be offered at any time during Contract. Special, time-limited reductions
are permissible under the following conditions: 1) reduction is available to all users equally; 2)
reduction is for a specific period, normally not less than thirty (30) days; and 3) original price
is not exceeded after the time-limit. Contractor shall offer Region 4 ESC any published price
reduction during the Contract term.
18) Audit Rights. Contractor shall, at its sole expense, maintain appropriate due diligence of all
purchases made by Region 4 ESC and any entity that utilizes this Contract. Region 4 ESC
reserves the right to audit the accounting for a period of three (3) years from the time such
purchases are made. This audit right shall survive termination of this Agreement for a period
of one (1) year from the effective date of termination. Region 4 ESC shall have the authority
to conduct random audits of Contractor’s pricing at Region 4 ESC's sole cost and expense.
Notwithstanding the foregoing, in the event that Region 4 ESC is made aware of any pricing
being offered that is materially inconsistent with the pricing under this agreement, Region 4
ESC shall have the ability to conduct an extensive audit of Contractor’s pricing at Contractor’s
CONTRACT
4
sole cost and expense. Region 4 ESC may conduct the audit internally or may engage a third-
party auditing firm. In the event of an audit, the requested materials shall be provided in
the format and at the location designated by Region 4 ESC. Notwithstanding the foregoing,
Region 4 ESC’s audit rights shall apply only to orders placed under the Contract. In no
event will Contractor’s liability for the cost of any audit exceed $10,000.
19) Discontinued Products. If a product or model is discontinued by the manufacturer, Contractor
may substitute a new product or model if the replacement product meets or exceeds the
specifications and performance of the discontinued model and if the discount is the same or
greater than the discontinued model.
20) New Products/Services. New products and/or services that meet the scope of work may be
added to the Contract. Pricing shall be equivalent to the percentage discount for other
products. Contractor may replace or add product lines if the line is replacing or supplementing
products, is equal or superior to the original products, is discounted similarly or greater than
the original discount, and if the products meet the requirements of the Contract. No products
and/or services may be added to avoid competitive procurement requirements. Region 4 ESC
may require additions to be submitted with documentation from Members demonstrating an
interest in, or a potential requirement for, the new product or service. Region 4 ESC may reject
any additions without cause.
21) Options. Optional equipment for products under Contract may be added to the Contract at
the time they become available under the following conditions: 1) the option is priced at a
discount similar to other options; 2) the option is an enhancement to the unit that improves
performance or reliability.
22) Warranty Conditions. All supplies, equipment and services shall include manufacturer's
minimum standard warranty and one (1) year labor warranty unless otherwise agreed to in
writing. Contractor will provide the manufacturer’s Limited Product Warranty as the exclusive warranty furnished
for equipment, goods or materials furnished pursuant to the Contract. Services performed by Contractor (or its
subcontractors) are guaranteed to meet industry standards for a period of one (1) year from completion of such
services. THESE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THOSE OF MERCHANTABILITY AND FITNESS FOR A SPECIFIC
PURPOSE WHICH ARE HEREBY SPECIFICALLY DISCLAIMED
23) Site Cleanup. Contractor shall clean up and remove all debris and rubbish resulting from their
work as required or directed. Upon completion of the work, the premises shall be left in good
repair and an orderly, neat, clean, safe and unobstructed condition.
24) Site Preparation. Contractor shall not begin a project for which the site has not been prepared,
unless Contractor does the preparation work at no cost, or until Region 4 ESC includes the
cost of site preparation in a purchase order. Site preparation includes, but is not limited to
moving furniture, installing wiring for networks or power, and similar pre-installation
requirements.
25) Registered Sex Offender Restrictions. For work to be performed at schools, Contractor
agrees no employee or employee of a subcontractor who has been adjudicated to be a
registered sex offender will perform work at any time when students are or are reasonably
expected to be present. Contractor agrees a violation of this condition shall be considered a
material breach and may result in the cancellation of the purchase order at Region 4 ESC’s
discretion. Contractor must identify any additional costs associated with compliance of this
term. If no costs are specified, compliance with this term will be provided at no additional
charge.
26) Safety measures. Contractor shall take all reasonable precautions for the safety of employees
on the worksite and shall erect and properly maintain all necessary safeguards for protection
of workers and the public. Contractor shall post warning signs against all hazards created by
its operation and work in progress. Proper precautions shall be taken pursuant to state law
CONTRACT
5
and standard practices to protect workers, general public and existing structures from injury or
damage.
27) Smoking. Persons working under the Contract shall adhere to local smoking policies.
Smoking will only be permitted in posted areas or off premises.
28) Stored materials. Upon prior written agreement between the Contractor and Region 4 ESC,
payment may be made for materials not incorporated in the work but delivered and suitably
stored at the site or some other location, for installation at a later date. An inventory of the
stored materials must be provided to Region 4 ESC prior to payment. Such materials must be
stored and protected in a secure location and be insured for their full value by the Contractor
against loss and damage. Contractor agrees to provide proof of coverage and additionally
insured upon request. Additionally, if stored offsite, the materials must also be clearly identified as
property of Region 4 ESC and be separated from other materials. Region 4 ESC must be allowed
reasonable opportunity to inspect and take inventory of stored materials, on or offsite, as
necessary. Until final acceptance by Region 4 ESC, it shall be the Contractor's
responsibility to protect all materials and equipment. Contractor warrants and guarantees that title
for all work, materials and equipment shall pass to Region 4 ESC upon final acceptance.
29) Funding Out Clause. A Contract for the acquisition, including lease, of real or personal
property is a commitment of Region 4 ESC’s current revenue only. Region 4 ESC retains the right
to terminate the Contract at the expiration of each budget period during the term of the Contract
and is conditioned on a best effort attempt by Region 4 ESC to obtain appropriate funds for
payment of the contract, provided, however, that any purchase order or agreement for the sale of
materials, equipment or services accepted by contractor prior to such termination shall not be
terminated or canceled but instead negotiated to continue through their completion and payment
with the public agencies..
30) Indemnity. Contractor shall protect, indemnify, and hold harmless both Region 4 ESC and its
administrators, employees and agents against all claims, damages, losses and expenses
from bodily injury or damage to tangible property to the extent resulting from the
negligent actions of the Contractor, Contractor employees or subcontractors in the
preparation of the solicitation and the later execution of the Contract. Any litigation involving
either Region 4 ESC, its administrators and employees and agents will be in Harris County, Texas.
31) Marketing. Upon prior written request to and written approval by Contractor, Contractor
agrees to allow Region 4 ESC to use their name and logo within website, marketing
materials and advertisement. Any use of Region 4 ESC name and logo or any form of publicity,
inclusive of press releases, regarding this Contract by Contractor must have prior approval from
Region 4 ESC. Any such permission for use to provided by Contractor to Region 4 ESC shall
terminate upon notice by Contractor or termination of this Agreement.
32) Certificates of Insurance. Certificates of insurance shall be delivered to the Region 4 ESC
prior to commencement of work. The Contractor shall give Region 4 ESC a minimum of ten
(10) days’ notice prior to any modifications or cancellation of policies. The Contractor shall
require all subcontractors performing any work to maintain coverage as specified.
33) Legal Obligations. It is Contractor’s responsibility to be aware of and comply with all local,
state, and federal laws governing the sale of products/services and shall comply with all laws
while fulfilling the Contract. Applicable laws and regulation must be followed even if not
specifically identified herein.
34) Limitation of Liability. NOTWITHSTANDING ANYTHING TO THE CONTRARY CONTAINED WITHIN
THE CONTRACT, IN NO EVENT WILL EITHER PARTY BE LIABLE FOR SPECIAL, INCIDENTAL,
INDIRECT, PUNITIVE, CONSEQUENTIAL, DELAY OR LIQUIDATED DAMAGES FOR ANY
REASON WHETHER OR NOT FORESEEABLE, NOR SHALL EITHER PARTY SEEK OR APPLY
FOR SUCH DAMAGES. 'CONSEQUENTIAL DAMAGE' INCLUDES, WITHOUT LIMITATION, LOSS
OF ANTICIPATED PROFITS; BUSINESS INTERRUPTION; LOSS OF USE, REVENUE, AND
REPUTATION OR DATA. IN NO EVENT WILL EITHER PARTY’S LIABILITY HEREUNDER,
WHETHER IN LAW, EQUITY, CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY
OR OTHERWISE, EXCEED THE PRICE PAID OR PAYABLE FOR THE EQUIPMENT, GOODS OR
SERVICES GIVING RISE TO THE CLAIM."
CONTRACT
6
Appendix B
TERMS & CONDITIONS ACCEPTANCE FORM
Signature on the Offer and Contract Signature form certifies complete acceptance of the terms
and conditions in this solicitation and draft Contract except as noted below with proposed
substitute language (additional pages may be attached, if necessary). The provisions of the
RFP cannot be modified without the express written approval of Region 4 ESC. If a proposal
is returned with modifications to the draft Contract provisions that are not expressly approved
in writing by Region 4 ESC, the Contract provisions contained in the RFP shall prevail.
Check one of the following responses:
Offeror takes no exceptions to the terms and conditions of the RFP and draft Contract.
(Note: If none are listed below, it is understood that no exceptions/deviations are taken.)
x Offeror takes the following exceptions to the RFP and draft Contract. All exceptions must
be clearly explained, reference the corresponding term to which Offeror is taking exception
and clearly state any proposed modified language, proposed additional terms to the RFP
and draft Contract must be included:
(Note: Unacceptable exceptions may remove Offeror’s proposal from consideration for
award. Region 4 ESC shall be the sole judge on the acceptance of exceptions and
modifications and the decision shall be final.
If an offer is made with modifications to the contract provisions that are not expressly
approved in writing, the contract provisions contained in the RFP shall prevail.)
Section/Page Term, Condition, or Exception/Proposed Modification Accepted
Specification (For Region 4
ESC’s use)
See Following Pages for Complete list of Exceptions/Proposed Modifications
Deviation Form - Daikin Applied Americas Inc
Term, Condition or Accepted (For
Section/Page Exception/Proposed Modification
Specification Region 4 ESC’s use)
APPENDIX A, DRAFT CONTRACT
On line 1 of the last paragraph of the Section, replace “ten (10) days” with “a
reasonable period of time.” Approved
On line 3 of the last paragraph of the Section, after “under this paragraph,”
Section 11.a) / Cancellation for Non-Performance insert, “and upon payment for work and materials already performed or
Approved
CONTRACT 2 or Contractor Deficiency furnished.”
At the end of the Section, insert, “References to 'specifications' herein shall
be construed to mean approved submittals relating to equipment furnished
Approved
by Contractor."
Replace Section in its entirety with, "Reserved." Section is generally
Section 11.b) /
Termination for Cause duplicative of Section 11.a), and to the extent it differs, creates inconsistency
CONTRACT 3 Approved
and conflict with the parties' obligations under the contract
On lines 1 through 4 of the Section, replace, "the time specified, or ...
Approved
Contract to be terminated," with, “a mutually agreed timeframe or failure to
make repairs, replacements or corrections in accordance with the applicable
warranty (as defined below) shall constitute grounds for the Contract to be
terminated, subject to the provisions set forth in Section 11.a) providing for
Section 11.c) /
Delivery/Service Failures notice to Contractor and Contractor’s reasonable opportunity to cure any
CONTRACT 3
alleged unmet performance obligation."
On Lines 4 through 6 of the Section, delete the last sentence in its entirety, to
Approved
wit: “In the event Region 4 ESC must purchase in an open market, Contractor
agrees to reimburse Region 4 ESC, within a reasonable time period, for all
expenses incurred."
At the end of the Section, insert, “Any purchase order, service order or
Approved
Section 11.e) / agreement to procure goods and services already accepted by Contractor
Standard Cancellation
CONTRACT 3 prior to such termination shall continue through its fulfillment and payment,
notwithstanding any termination of this Contract.”
On line 1 of the Section, insert the following after Purchase Order, "or as
Section 14 /
Delivery otherwise indicated by Contractor or the applicable manufacturer." Approved
CONTRACT 4
In the last sentence of Section 14, insert “First” before “Destination” Approved
On line 2 of the Section, following, "Region 4 ESC," insert, "provided that
Approved
Section 15 / before such return Region 4 ESC and contractor have mutually agreed on a
Inspection & Acceptance
CONTRACT 4 timeframe within which contractor may cure the alleged defect or incorrect
delivery and allow the contractor to effect such cure.”
At the end of the Section, insert, "but in no event later than sixty (60) days
Section 16 /
Payments from
CONTRACT 4
invoice date.” Approved
To the end of Section 18, add the following, “Notwithstanding the foregoing,
Approved
Section 18 / Region 4 ESC’s audit rights shall apply only to orders placed under the
Audit Rights
CONTRACT 4,5 Contract. In no event will Contractor’s liability for the cost of any audit
exceed $10,000.”
At the end of the Section, insert, “Contractor will provide the manufacturer’s Approved
Limited Product Warranty as the exclusive warranty furnished for
equipment, goods or materials furnished pursuant to the Contract. Services
performed by Contractor (or its subcontractors) are guaranteed to meet
Section 22 / industry standards for a period of one (1) year from completion of such
Warranty Conditions
CONTRACT 5 services. THESE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THOSE OF
MERCHANTABILITY AND FITNESS FOR A SPECIFIC PURPOSE WHICH ARE
HEREBY
SPECIFICALLY DISCLAIMED.”
To the end of section 29 add the following “, provided, however, that any
Approved with the
purchase order or agreement for the sale of materials, equipment or services following modification:
Section 29 /
Funding out Clause accepted by contractor prior to such termination shall not be terminated or insert "negotiated to"
CONTRACT 6 after the word
cancelled but instead continue through their completion and payment with 'instead'
the public agencies.”
On Line 3 of the Section, delete, "arising out of or resulting," and
Section 30 / replace, "the actions," with, "bodily injury or damage to tangible
Indemnity Approved
CONTRACT 6 property to the extent
resulting from the negligent actions."
Term, Condition or Accepted (For
Section/Page Exception/Proposed Modification
Specification Region 4 ESC’s use)
APPENDIX A, DRAFT CONTRACT
At the beginning of the Section, insert, "Upon prior written request to and
Approved
written approval by Contractor."
Section 31 /
Marketing At the end of the Section, insert, "Any such permission for use to provided by
CONTRACT 6
Contractor to Region 4 ESC shall terminate upon notice by Contractor or
Approved
termination of this Agreement."
Insert the following as Section 34: Approved
"34) Limitation of Liability. LIMITATION OF LIABILITY: NOTWITHSTANDING
ANYTHING TO THE CONTRARY CONTAINED WITHIN THE CONTRACT, IN NO
EVENT WILL EITHER PARTY BE LIABLE FOR SPECIAL, INCIDENTAL, INDIRECT,
PUNITIVE, CONSEQUENTIAL, DELAY OR LIQUIDATED DAMAGES FOR ANY
Section 34 / NEW SECTION: Limitation of REASON WHETHER OR NOT FORESEEABLE, NOR SHALL EITHER PARTY SEEK
CONTRACT 6 Liability OR APPLY FOR SUCH DAMAGES. 'CONSEQUENTIAL DAMAGE' INCLUDES,
WITHOUT LIMITATION, LOSS OF ANTICIPATED PROFITS; BUSINESS
INTERRUPTION; LOSS OF USE, REVENUE, AND REPUTATION OR DATA. IN
NO EVENT WILL EITHER PARTY’S LIABILITY HEREUNDER, WHETHER IN LAW,
EQUITY, CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY OR
OTHERWISE, EXCEED THE PRICE PAID OR PAYABLE FOR THE EQUIPMENT,
GOODS OR SERVICES GIVING RISE TO THE CLAIM."
EXHIBIT B - ADMINISTRATION AGREEMENT EXAMPLE FOR REGION IV ESC
TERMS AND At the end of the Section, insert, "LIKEWISE, SUPPLIER SHALL NOT BE LIABLE
CONDITIONS Limitation of Liability IN ANY WAY FOR ANY SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENTIAL, OMNIA Partners will
negotiate
Section 8 / Page 3 EXEMPLARY, PUNITIVE, OR RELIANCE DAMAGES."
TERMS AND OMNIA Partners will
On Line 9 of the Section, insert, "undisputed," between, "All," and,
CONDITIONS Administrative Fee Payments negotiate
"Administrative Fees."
Section 14 / Page 4
ONLINE Documentation
Exhibit F
Rights to Inventions Made Under a Section 7 is stricken in its entirety. Contractor reserves all intellectual
Online Response
Contract or Agreement property rights.
OMNIA Partners
Attachment #13. will review.
Strike this section and replace with, ‘Supplier projects, but does not
Approved
guarantee, OMNIA contract sales in the first three years of the contract to
ONLINE Response be:
BID ATTRIBUTES Contract Sales $172M in year one (#77)
Items 77, 78, 79 $198M in year two (#78)
$228M in year three (#79)
24-09 Addendum 3
Daikin Applied Americas, Inc
Supplier Response
Event Information
Number: 24-09 Addendum 3
Title: HVAC Solutions, Related Products and Services
Type: Request for Proposal
Issue Date: 6/20/2024
Deadline: 8/1/2024 02:00 PM (CT)
Notes: PLEASE NOTE THAT THE BOARD MEETING DATE HAS BEEN
CHANGED TO OCTOBER 29, 2024.
Oral communications concerning this RFP shall not be binding and
shall in no way excuse an Offeror of the obligations set forth in this
proposal.
Only online proposals will be accepted. Proposals must be submitted
via Region 4 ESC's online procurement system:
region4esc.ionwave.net.
No manual, emailed, or faxed proposals will be accepted.
NON-MANDATORY PRE-PROPOSAL CONFERENCE
Meeting to be held on
Wednesday, July 17, 2024 at 10:00 am
via ZOOM. Click here to join.
Offerors are strongly encouraged, but not required to participate in a
pre-proposal conference with the Procurement and Operations
Specialist.
Page 1 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
Contact Information
Address: Finance and Operations
7145 West Tidwell Road
TX 77092
Email: questions@esc4.net
Page 2 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
Daikin Applied Americas, Inc Information
Contact: Greg Coffman
Address: 13600 Industrial Park Blvd
Plymouth, MN 55441
Phone: (763) 353-2252
Email: greg.coffman@daikinapplied.com
Web Address: www.daikinapplied.com
By submitting your response, you certify that you are authorized to represent and bind your company.
Gregory R. Coffman greg.coffman@daikinapplied.com
Signature Email
Submitted at 8/1/2024 09:25:57 AM (CT)
Supplier Note
Thank you for this to resubmit our application for this opportunity, as we have been a long standing member of
Region 4, and we look forward to continued success and achievement of our shared goals with our partnership.
Requested Attachments
1 - Products and Pricing - Daikin
Products and Pricing Applied Product and Pricing -
Final.pdf
Each offeror awarded an item under this solicitation may offer their complete product and service offering/a balance of
line. Describe the full line of products and services offered by supplier.
Proposed Pricing Coefficient(s) No response
Please complete the Proposed Pricing Coefficient(s), located on the Attachments tab, and upload the completed
document here.
3 - Value Added Services - Daikin
Value Added Services Applied Value Added Services -
Final.pdf
Provide any additional information related to products and services the Offeror proposes to enhance and add value to
the Contract. For example, a proposal for furniture may include additional value-added selections such as installation,
white glove delivery options, setup/cleaning, classroom design/layout, special orders, etc. (OPTIONAL)
4 - 24-09 Offer and Contract
Contract and Offer Form and Deviation Form Signature Form and Deviation
Form - Daikin Applied - Final.pdf
Please complete the Contract and Offer Form and Deviation Form, located on the Attachments tab, and upload the
completed document here.
Acknowledgment and Acceptance of Region 4 ESC's Open Records 5 - Acknowledgment and
Acceptance of Region 4 ESCs
Policy Open Records Policy - DA.pdf
Please complete the Acknowledgment and Acceptance of Region 4 ESC's Open Records Policy, located on the
Attachments tab, and upload the completed document here.
6 - Antitrust Certification
Antitrust Certification Statements Statements - Daikin Applied -
Final.pdf
Please complete the Antitrust Certification Statements, located on the Attachments tab, and upload the completed
document here.
Page 3 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
7 - Disclosure of Interested Parties
Disclosure of Interested Parties form or Evidence of Exemption form or Evidence of Exemption -
1295 Form - DA.pdf
If you are required under statute to submit a Disclosure of Interested Parties form (1295 form), you must do so here.
Section 6 must be completed in its entirety. Alternatively, if you are exempt under the statute, you must provide
documentation affirming your exemption. (REQUIRED, see Attribute titled "DISCLOSURE OF INTERESTED PARTIES")
Additional Agreements Offeror will require Participating Agencies to 8 - Additional Agreements - Daikin
Applied Contractor Agreement -
sign. Final.pdf
Upload any additional agreements offeror will require Participating Agencies here.
9 - Texas Government Code 2270
Texas Government Code 2270 Verification Form Verification Form - Daikin Applied -
Final.pdf
Please complete the Texas Government Code 2270 Verification Form, located on the Attachments tab, and upload the
completed document here.
Diversity, HUB Certifications No response
If your firm holds a certification from certifying agencies related to M/WBE, DBE, HUB, or other diverse business
designations, you may upload the certificate here. (OPTIONAL)
11 - Conflict of Interest - Daikin
Conflict of Interest Questionnaire Applied - Final.pdf
If a conflict exists that requires the submission of a Conflict of Interest Questionnaire (CIQ), complete and upload the
document here. (REQUIRED ONLY IF A CONFLICT EXISTS, see Attribute titled "CONFLICT OF INTEREST
QUESTIONNAIRE" for additional information.)
12 - W-9 Upload - Daikin Applied
W-9 Upload W-9 (2024) - Final.pdf
Interested offerors must upload an updated Form W-9 prior to submitting a proposal.
13 - OMNIA Partners - Exhibit F
OMNIA Partners - Exhibit F Federal Funds Certifications Federal Funds Certifications -
Daikin Applied - Final.pdf
Please complete the OMNIA Partners - Exhibit F Federal Funds Certifications, located on the Attachments tab, and
upload the completed documents here.
14 - OMNIA Partners - Exhibit G
OMNIA Partners - Exhibit G New Jersey Business Compliance New Jersey Compliance - Daikin
Applied - Final.pdf
Please complete the OMNIA Partners - Exhibit G New Jersey Business Compliance forms, located on the Attachments
tab, and upload the completed documents here.
Bid Attributes
1 CONTRACT DURATION
The initial term of the Contract is for a period of three (3) years unless terminated, canceled, or extended as
otherwise provided herein. Region 4 ESC shall have the right in its sole discretion to renew the Contract for
additional terms up to two (2) years after the end of the initial term or for a lesser period of time as determined by
Region 4 ESC by providing written notice to the Contractor of Region 4 ESC’s intent to renew thirty (30) days prior
to the expiration of the original term. Contractor acknowledges and understands Region 4 ESC is under no
obligation whatsoever to extend the term of this Contract. In the event the proposal term, including renewals, ends
before another proposal is executed, proposal prices and discounts may be extended on a month-to-month basis
by mutual consent. Extensions are limited to the lesser of: a) six (6) additional monthly terms, or b) the time which is
required to complete a new solicitation for the goods and services provided for in this solicitation. Notwithstanding
the foregoing paragraph, the term of the Contract, including any extension of the original term, shall be further
extended until the expiration of any Purchase Order issued within the Contract term for a period of up to one year
beyond the Contract term.
I certify compliance with this attribute.
Page 4 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
2 NAME OF INDIVIDUAL COMPLETING THIS PROPOSAL
Greg Coffman
3 HOW MANY YEARS HAS YOUR BUSINESS OPERATED UNDER ITS PRESENT NAME
100
4 WHAT IS YOUR CURRENT NUMBER OF CUSTOMER ACCOUNTS?
49992
5 WHAT ARE YOUR BUSINESS HOURS?
While our business offices are traditional working hours, our factories are staffed with multiple shifts depending on
factory loading. As for service offices, they are oncall 24/7 to support our customers.
6 IS 30 DAYS AFTER RECEIPT OF INVOICE AN ACCEPTABLE PAYMENT SCHEDULE FOR YOUR
BUSINESS?
If Yes, type "YES".
If No, describe your payment schedule in the field provided.
Daikin's payment terms are Net 30 from date of invoice.
7 WHAT IS THE STANDARD LEAD TIME FOR RECEIPT OF PRODUCTS AFTER ORDER IS RECIEVED
(ARO), IN DAYS?
Provide your answer in number of DAYS after receipt of order (ARO).
We manufacturer custom equipment specific to the customers needs so it is difficult to provide a standard lead
time in number of days. We do have multiple parts warehouses across the country and are able to ship 98% of
customer products within the same day, this includes all OEM products not just Daikin Applied.
8 ACCOUNT MANAGER NAME
Please indicate the name of the account manager we should speak to with concerns about the products and/or
services in this proposal.
Greg Coffman
9 ACCOUNT MANAGER EMAIL
greg.coffman@daikinapplied.com
1 ACCOUNT MANAGER PHONE
0
(763) 353-2252
1 PAYMENT REMITTANCE ADDRESS
1
24827 Network Place, Chicago, IL 60673-1248
1 PAYMENT REMITTANCE PHONE
2
(763) 553-5330
Page 5 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 CONTRACT/PURCHASE ORDER/QUOTE EMAIL
3 Vendors may choose to have purchase orders emailed to them in PDF format in lieu of having them faxed or mailed.
To elect this option, please offer the preferred email address in the accompanying field. This email address will
apply to any purchases from your company, so the use of a generic email address is suggested, such as
bids@companyname.com or purchaseorders@businessname.com.
nationalaccounts@daikinapplied.com
1 CONTRACT/PURCHASE ORDER/QUOTE FAX NUMBER, IF APPLICABLE
4 If applicable, please provide a fax number to send orders and quote requests.
1 REQUIRED REFERENCE QUOTE OR CONTRACT NUMBER, IF APPLICABLE
5 Enter your quote or contract number and/or any other information our staff would need provide on the face of
purchase orders in order to receive discount percentages and contract pricing.
Daikin's Current Contract Number is R200401. We would require the same information for future contracts.
1 COMPANY WEBSITE ADDRESS, IF APPLICABLE
6
www.daikinapplied.com
1 HOW WERE YOU NOTIFIED OF THIS BID OPPORTUNITY?
7 In order to verify the efficiency of communication tools used to notify vendors of bidding opportunities, we ask that
you provide us with the manner in which you received notification of this request for bid/proposal.
We were notified by our business development manager, Chris Church, at OMNIA Partners.
1 REFERENCE 1
8 Please provide the reference of a school and/or business who have utilized the same equipment/products within the
last two years. Include Company/Government name, address, contact name, and contact phone number.
Garrett County Public Schools/Grantsville Elementary School 120 Grant Street Grantsville, MD 21536 Richard
Wesolowski 301-334-8905 Garrett County Public Schools (GCPS) in Maryland faced with a dilemma. While
pursuing major upgrades to Grantsville elementary school, it was determined that the architect and engineer had
designed an expensive design that would soon exceed the budget. Open classrooms, not conducive to modern
learning, were being redesigned with new walls, added lighting, doors, air conditioning and security systems. The
complicated plan resulted in a constant stream of incoming change orders. In addition, the current contractor was
experiencing performance issues and change orders were becoming a routine occurrence. Rather than scrap the
plan, GCPS decided to pursue a different approach. With the support of the Maryland Public School Construction,
the district partnered with Daikin Applied, through an OMNIA Partners cooperative contract. The choice was
primarily due to the district’s ability to take advantage of the consulting services offered by the contract. “Working
directly with the district, we were able to meet with the architect and engineer and re-design the project on a fast
track to stay within the budget,” says Sean McCarthy, Senior Account Manager for Daikin Applied. “With the
eventual use of over 26 subcontractors, it was important to have one point of contact to coordinate all the project
elements.” In addition to the $6.2 million classroom modernization for the elementary school, the district also
undertook a major upgrade for South Garrett High School. The high school had unique requirements in combining
the 7th and 8th grades with the current high school population. Many obstacles were overcome to support the
extracurricular activities with upgrades to bleachers, locker rooms and a brand-new dance studio, while also
creating educational spaces that adequately kept individual grades as close together as possible. McCarthy
further shares, “The elementary gym floor proved to be a challenge as the project occurred during the pandemic
and the wood flooring was not available. Since the gym was used for multi-recreational needs, it was decided to
use decorative tiles as part of the design. Working with the gym teacher, distinct tiles were placed to incorporate
the student activities conducted within the gym. This was a creative solution to a supply chain issue.”
1 REFERENCE 1 EMAIL
9
wesolowski@garrettcounty.org
Page 6 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
2 REFERENCE 2
0 Please provide the reference of a school and/or business who have utilized the same equipment/products within the
last two years. Include Company/Government name, address, contact name, and contact phone number.
Frederick County Public Schools 191 South East Street Frederick, MD 21701 Keith Marconi 227-203-3277
2 REFERENCE 2 EMAIL
1
keith.marconi@fcps.org
2 REFERENCE 3
2 Please provide the reference of a school and/or business who have utilized the same equipment/products within the
last two years. Include Company/Government name, address, contact name, and contact phone number.
Henry County 307 West Center Street Cambridge, IL 61238 Erin Knackstedt 309-937-3400
2 REFERENCE 3 EMAIL
3
eknackstedt@henrycty.com
2 THE U.S. STATE YOUR PRINCIPAL PLACE OF BUSINESS IS LOCATED.
4
Minnesota
2 RECIPROCITY
5 For Businesses not located in Texas: Does your state of residence or incorporation require out-of-state bidders to
underbid vendors residing in your state by a prescribed amount or percentage to receive a comparable contract? If
Yes, please input that percentage; If No, please leave the adjacent field blank.
No response
2 PARTIAL AWARD ACCEPTANCE
6 REGION 4 ESC retains the right to award this contract in such a manner that it receives the best overall value for
the goods and/or services requested in this request for proposal or bid, which may include awarding to multiple
vendors.
I understand.
2 PURCHASE ORDER POLICY
7 REGION 4 ESC purchases tangible goods and services through the use of approved Purchase Orders. Vendors
are highly discouraged from sending products, and/or performing services without prior receipt of an approved
District Purchase Order. While campuses and departments may call for quotes and information, please be advised
the District is not obligated to pay for any services and/or products ordered via telephone or email in without the
presence of a properly executed Purchase Order.
I understand.
2 ADDENDA NOTIFICATIONS
8 Any addenda to this proposal will be issued electronically through this system. It is vendor's responsibility to review
addenda upon e-mailed notice and retract/amend their submission as deemed necessary. REGION 4 ESC may
choose to mark a proposal received prior to the issuance of an addendum as non-responsive should REGION 4
ESC, in its sole determination, finds the addendum to be of such material change that it warrants such
determination. If such proposal is found non-responsive, REGION 4 ESC will not consider the proposal for
evaluation or further consideration.
I understand.
Page 7 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
2 Provide equipment manufacturer, equipment types and discounts off published list price.
9
Attachment Required - File: Daikin Applied - Products and Pricing - Bid Invitation 24-09 Daikin Applied’s bid
response includes the full catalog of Daikin HVAC Equipment (including, but not limited to, Chillers, Condensing
Units, Rooftop Systems, Water Source Heat Pumps, Fan Coils, Air Handling Units, Unit Ventilators, VAV/VRV,
Modular Chiller Plants, and Parts) as well as equipment and parts for nearly 200 additional manufacturers
covering 14 HVAC product categories. Daikin Applied proposed discounts range from 10-47%. For full list of
equipment manufacturers, equipment types, and discount off published list prices please see Daikin Applied’s
attachment Daikin Applied - Products and Pricing - Bid Invitation 24-09
3 Define any freight charges.
0
FOB Factory, Freight Allowed.
3 Describe how Offeror responds to emergency orders.
1
Daikin provides 24/7 emergency response for our clients through Daikin's 150+ office locations throughout North
America with over 3,000 sales, support staff and 9 dedicated CSRs. Daikin maintains a stock equipment report
listing ready to ship equipment same week. Daikin also provides a 24 hour - 7 days per week 1-800 number for
immediate response and service. In our Emergency Order process, a customer can escalate an order for parts
with a possible emergency fee, if applicable. In most cases, we are able to improve on the ship date for the
customer by working with Plants and Suppliers.
3 What is Offeror's average Fill Rate?
2
Our fill rate at our parts stores are 98% ship within that day, it is difficult to detail fill rate on custom equipment.
3 What is Offeror's average on time delivery rate? Describe Offeror’s history of meeting the shipping and
3 delivery timelines.
OTD varies by factory and product line, to manage customer expectations, we publish weekly lead times so we
have accurate information to the field.
3 Describe Offeror's return and restocking policy.
4
Given we manufacture custom equipment, it is difficult to return those products. We do have ability to cancel
orders in event of project changes, however, there may be fee if we have incurred production costs. As for parts,
these can be returned with small restocking fee.
3 Describe Offeror's ability to meet service and warranty needs.
5
We have over 150 service office locations thorugh North American with over 3,000 sales and support staff. We
also have dedicated Warranty department by product line to support our service teams, this includes regional
technical teams to dispatch to site for emergency warranty work.
3 Describe Offeror's customer service/problem resolution process. Include hours of operation, number
6 of services, etc.
Daikin provides a 24 hour, 7 days per week 1-800 number for immediate response and customer service. These
incoming calls are qualified and sent to the appropriate technicians, service, parts, rentals, residential, accounts
payable/receivable or local representatives. Case numbers are assigned to each request for efficient and timely
responses and follow-up as well as internal tracking and resolution. Our website also offers service information for
products, service, parts, solutions, and related resources. We have 9 dedicated CSRs for customer service
resolution and escalation for order status, lead times, shipping, and general questions normally 8am-4:30pm CST
daily.
Page 8 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
3 Describe Offeror's invoicing process. Include payment terms and acceptable methods of payments.
7 Offerors shall describe any associated fees pertaining to credit cards/p-cards.
For equipment only orders, we invoice at time of shipment of equipment. Invoicing my vary for service depending
on scope and size of work (milestones, completion of the work, etc). We don’t allow payment by credit card on
customer accounts with 30 day terms. For those customers that mandate payment by credit card with no options,
the additional fees are included in the quotations. Credit Card Policy – 4/5/22 • Credit cards can be used to pay
invoices up to 10 days old; invoices beyond this date must be paid by check or ACH; • Credit card payments
greater than $25,000 must be approved by the Director of Credit or higher; • We do not accept credit card
payments for our equipment orders.
3 Describe Offeror's contract implementation/customer transition plan.
8
Daikin Applied will continue to promote the Master Agreement to its public customers as it does with its current
Region 4 ESC contract. Daikin Applied’s sales teams lead sales discussions with the value and benefits of
cooperative purchasing. In many cases, customers issue a purchase addendum stating all purchases between
Daikin Applied and the Public Agency must be based on Daikin Applied’s Region 4 ESC contract. Daikin Applied’s
current cooperative contracts are with the General Services Administration (GSA contracts), TIPS and BuyBoard.
Daikin’s GSA contracts are used with federal customers, and it’s BuyBoard contract is specific to the South Central
Region. Both contracts include only Daikin Applied products and labor, which is a minimal offering to public
agencies. Daikin Applied presents its Region 4 ESC Master Agreement as the lead contract procurement vehicle.
TIPS, GSA or BuyBoard are provided only if the customer expresses a specific preference for these programs.
3 Describe the financial condition of Offeror.
9
Daikin Applied's sales for FY23 (ending March 2024) exceeded $2.5B and strong OI. Daikin Applied is a wholly
owned subsidiary of Daikin Industries LTD headquartered in Osaka, Japan. We are truly a global company.
4 Provide a website link in order to review website ease of use, availability, and capabilities related to
0 ordering, returns and reporting. Describe the website’s capabilities and functionality.
www.daikinapplied.com
4 Describe the Offeror’s safety record.
1
The interstate experience modification factor as calculated by the National Council on Compensation Insurance,
Inc. (NCCI) for Daikin Holdings America, Inc. for the past three years is as follows: Effective Date (Interstate
Experience Modification Factor) -- 4/01/2022 (.78) - 4/01/2023 (.70) - 4/01/2024 (.66)
4 Provide a brief history of the Offeror, including year it was established and corporate office location.
2
Headquartered in Plymouth, MN, Daikin Applied is part of Daikin Industries, Ltd. which is the largest global HVAC
manufacturer for commercial, industrial and residential air conditioning systems, and the global air conditioning
leader. In North America, Daikin Applied provides expertise in commercial HVAC systems with technologically
advanced and highly applied systems. In 2006, Daikin Applied acquired McQuay International, and spent the next
five years implementing processes and quality enhancements prior to adding Daikin to the McQuay name.
Founded in 1924, we have a heritage of producing applied products for 100 years, Daikin Applied continues to
grow by leveraging the knowledge and resources which has made Daikin Industries the global air conditioning
leader in the marketplace.
4 Describe Offeror's reputation in the marketplace.
3
As the world's largest AC company, Daikin Applied delivers superior air quality and energy efficiency to every
solution with innovation in advanced technology, IoT, and next generation compressors. Daikin branded products,
solutions, and services are sold through a global network of dedicated sales, service, and parts offices. Daikin
Applied’s parent company, Daikin Industries, Ltd. reports revenues in excess of $20 billion and has more than
67,000 employees worldwide, making it the largest HVAC manufacturer in the world. Daikin Industries, Ltd. has
more than 90 production sites worldwide and works with customers in more than 150 countries. Recent Expansions
Daikin Applied has recently expanded its manufacturing facilities to California and Tijuana, Mexico, indicating a
growing presence in the HVAC market. This expansion presents an opportunity for sales teams to tap into new
geographical markets and establish relationships with potential clients in these regions.
Page 9 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
4 Describe Offeror's reputation of products and services in the marketplace.
4
Daikin is a Japanese based company that specializes in the manufacturing of air conditioners and other HVAC
equipment. Daikin is a trusted name in the industry, and their products are known for being reliable, innovative,
and efficient helping them become a Fortune 1000 company. Combining advanced technologies and research and
development capabilities, Daikin Applied creates innovative products, systems and services that benefit the
industry and lives of our customers. Comparison to competitors-Daikin's premium AC units operate more quietly,
and they have a longer warranty. Both Daikin and Trane are at the top of the quality spectrum. One of the most
important factors to consider when choosing an air conditioner is its quality. Daikin is known for making durable,
high-quality products that are built to last. LG is also known for making high-quality products, but they tend to be
less durable than Daikin models.
4 Describe if distributors/dealers/resellers/subsidiaries/partners ("affiliates") will be used to fulfill the
5 contract. Submit a list of those affiliates authorized to sell under the proposed contract.
Where and how does Offeror propose to maintain an authorized affiliate list so it may be accessed by Participating
Agencies? How often does the supplier propose to update the affiliate list? Confirm the Offeror reviews the financial
health, debarment status and overall general capacity of authorized affiliates. Offerors who us authorized affiliates
are responsible for ensuring authorized affiliates are performing in accordance with the contract.
Daikin Applied goes to market in two ways: through independent manufacturer’s representatives and through
Daikin factory owned district service offices and independent service alliance partners. Daikin Applied’s
representative network Requirements for National Cooperative Contract has over 130 office locations throughout
North America with over 2,650 sales and support staff. Daikin Applied manufacturer representatives offers both
Daikin Applied and complimentary products as part of their offering to owners, engineers, and contractors. Daikin
Applied has eighty factory owned and service alliance partner locations throughout North America which include
over 450 sales and support staff. These service offices offer a wide variety of service solutions including quoted
repairs, maintenance contracts, and installation and turnkey contracting. Daikin Applied also has eighty-two parts
distributors and six Daikin Applied owned company parts stores for customer to access their aftermarket needs.
Through its expansive representative and service networks, Daikin Applied will offer all products and services in
the scope of this RFP to all 50 U.S. states, including U.S. territories and outlying areas. Daikin Applied maintains a
current distributor/dealer/reseller/subsidiary/partner list and will notify Region 4 and OMNIA Partners with any
update and request for authorization. Daikin Applied monitors and evaluates all existing and potential relationships
to confirm financial health, debarment status, and overall general capacity of authorized affiliates. Please see
attached document Daikin Applied – Equipment Sales Representative and Authorized Service Provider List for the
full list of distributor/dealer/reseller/subsidiary/partner.
4 Describe the experience and qualifications of key employees.
6
Yu Nishiwaki - COO brings an MBA and 24 years of experience at Daikin having served as VP of Strategic
Planning GM of Daikin's Italian office in Rome. John Moon - SVP Customer and Business Solutions brings an
engineering degree from Georgia Tech and 19 years with Daikin servicing as GM and VP East Division. James
Moe - SVP Sales and Service brings 23 years of HVAC experience, 8 with Daikin, and has served as RGM West
Division and DVP West Division before his current assignment. Keela Bakken - VP of National Accounts brings 25
years of building automation and HVAC experience serving Daikin as National Account Manager, Vertical Market
Manager, and Director of National Accounts before her current position. Daikin has a dedicated government team
responsible for the pomotion, management and compliance of our cooperative programs.
4 Describe Offeror's experience working with the government sector.
7
A large portion of Daikin Applied business has been in the government sector, primarily in the education market
with the first unit ventilator conditioning K-12 classrooms. In 2009, Daikin entered the government cooperative
market by obtaining the GSA federal supply schedule contract, which allowed Daikin to sell its products and
services directly to federal customers and later to state and local customers through GSA's COOP program. Daikin
invested in a government team to focus on state, local, and federal government sales and to maintain contract
compliance throughout the procurement process. Daikin Applied's GSA yearly contract sales grew to $15m+. In
2015, Daikin responded to Region 4 ESC's RFP 15-05 for HVAC Equipment, Installation, Service and Related
Products and was successfully awarded a national contract to support the state, local, and education markets.
Daikin Applied has continually surpassed its state Region 4 sales goals reaching now over $142m.
Page 10 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
4 Describe past litigation, bankruptcy, reorganization, state investigations of entity or current officers
8 and directors.
As Daikin Applied and its parent Daikin Industries are multi-billion-dollar entities, they are occasionally involved in
litigation. There are no known legal matters that would adversely affect Daikin Applied’s ability to perform under
this Agreement. Daikin Applied has not been involved in a bankruptcy or reorganization.
4 Provide Offeror's expertise in working with public sector and understanding of the unique technical
9 regulatory requirements.
We are anchored by our experienced program manager and contract compliance managers. They have worked 8
years extensively with GSA and OMNIA and in contracts and contract compliance for 10 years. The program
manager oversees processes and procedures, certification of proposals, contract modifications, and reporting.
The contract compliance manager makes sure we are up to date and within compliance on contracts and
modifications under his purview. The sales manager brings a sales, business and HVAC manufacturing
background leading the training and education of our sales and service teams. The National Account Managers
round out our team . We also have 2 dedicated business development managers promoting OMNIA and providing
expertise and guidance to their respective regions.
5 Indicate if Offeror is licensed to do business in all 50 states.
0
Yes
No
5 Value Add - Provide any additional information related to products and services Offeror proposes to
1 enhance and add value to the Contract.
Headquartered near San Diego, Alliance Air Products, the newest member of The Daikin group, is a Heating,
Ventilation, Air Conditioning and Refrigeration (HVACR) manufacturer, serving the OEM, Design-Build as well as
Plan and Spec marketplaces. Each piece of equipment that we manufacture is engineered to meet specific project
requirements, as well as to satisfy the owner/user’s needs and expectations. Our sales and engineering staff are
distinguished by their functional and technical expertise combined with their hands-on experience, to ensure that
our clients receive the most effective and professional service. As experts in custom HVACR manufacturing,
Alliance Air Products is involved in every stage of the process offering functional and technical support. Our
engineering and manufacturing skills encompass all aspects of implementation and operation. Whether you need
is for a standard air handler, complex package system or specialized construction that modular units can’t handle,
Alliance Air Products adds value by solving problems and giving you a solution that meets your needs. Alliance Air,
a subsidiary of Daikin Applied, a leading global commercial and industrial HVAC manufacturer, today broke ground
for the construction of a new energy-efficient manufacturing facility in Tijuana, Mexico to support sustainable data
center growth across North America. The new $121 million USD, 460,000 square-foot facility is expected to
support over 1,000 production jobs and over 1,150 total new permanent jobs in the northwest region of Mexico.
This investment will expand on the established presence of Alliance Air and Daikin Applied in Tijuana as the
company looks to support significant data center market growth in Mexico and North America. Construction of the
facility is expected to be complete by Spring 2025 with production ramping up in June 2025. This expanded facility
allows the company to better serve customers in North America with a single supplier for end-to-end HVAC
solutions. The expansion builds on the legacy of Alliance Air in Tijuana, which is also celebrating 20 years in the
community and now partnered with the 100-year legacy of industry leader Daikin Industries. “We started
manufacturing in Tijuana 20 years ago with 30 employees. We were just a start-up. I’m proud to see this force of
1,000 team members who have become exceptionally talented in the design and production of energy-efficient,
custom cooling solutions,” said Luis Plascencia, President and General Manager of Alliance Air Products. “We look
forward to expanding our role in the community and bolstering our partnership with the Baja California government
and local Tijuana leaders to make this new facility a reality.” The facility is being built to manufacture energy-
efficient HVAC cooling solutions specifically for data centers. It is designed for maximum efficiency to meet the
company’s and customers’ sustainability goals. “This is a critical moment for the HVAC industry to meet the
demand for data center cooling which is increasing exponentially with trends and economic forces like artificial
intelligence and insourcing manufacturing,” said Yu Nishiwaki, Chief Operating Officer for Daikin Applied Americas.
“Increasing our current capacity allows us to expedite delivery to help customers meet this demand. The combined
talent and technology of Alliance Air and Daikin Applied creates a new level of energy efficiency to help customers
meet aggressive sustainability goals.” See attached document in Value Add section for additional information.
Page 11 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
5 Include a per diem rate.
2
Daikin Applied Per Diem rates are included in the attached Products and Pricing attachment. Daikin Applied’s
complete list of equipment manufacturers, equipment types, and discount off published list prices please see
Daikin Applied’s attachment Daikin Applied - Products and Pricing - Bid Invitation 24-09
5 For Non-Normal Working Hours, indicate if there is a minimum charge of hours and what the number of
3 hours is.
Daikin Applied’s Non-Normal Working Hours (Overtime) is priced at 1.5x the approved Normal Working Hours
(Standard) hourly rate. Daikin Applied’s complete list of equipment manufacturers, equipment types, and discount
off published list prices please see Daikin Applied’s attachment Daikin Applied - Products and Pricing - Bid
Invitation 24-09
5 Is pricing available for all products and services?
4
Daikin Applied provides hourly rates for 50 HVAC and HVAC related labor services in the attached Products and
Pricing attachment. Daikin Applied offers customers a variety of state-of-the-art and highly customizable
equipment to meet the customer’s specific HVAC related needs. Daikin Applied’s availability to meet specific needs
results in thousands of protentional equipment configurations and product pricings. To simplify Daikin Applied
response the equipment discounts have been provided for each HVAC and HVAC related product family which can
be found in the Products and Pricing attachment. Daikin Applied’s complete list of equipment manufacturers,
equipment types, and discount off published list prices please see Daikin Applied’s attachment Daikin Applied -
Products and Pricing - Bid Invitation 24-09
5 Describe any shipping charges (where applicable).
5
FOB Factory. Freight Allowed.
5 Provide pricing for warranties on all products and services.
6
Daikin Applied provides a standard limited 12-month warranty on equipment, parts, and labor services with options
for additional extended parts and labor services with pricing varying due to equipment category, size, and quantity.
For a full review of Daikin Applied limited warranty please review attached document.
5 Describe any return or restocking fees.
7
All returns will be subject to a restocking /administration charge of 30% and a Daikin collection charge, which will
be applied to the final credit.
5 Describe any additional discounts or rebates available. Additional discounts or rebates may be offered
8 for large quantity orders, single ship to location, growth, annual spend, guaranteed quantity, etc.
Not Applicable
5 Describe how customers verify they are receiving Contract pricing.
9
Daikin Applied adheres to a strict compliance program with all its government cooperative contracts. This process
is managed by Daikin’s Government National Accounts team which works directly with Daikin’s sales and service
partners when a cooperative contract is utilized for procurement. In the case with Daikin’s Region 4 contract,
Daikin’s government team reviews all project estimates to ensure the awarded contract pricing has not been
exceeded. Once compliance is verified, Daikin’s government team registers all projects with a Certified Proposal
Number (CPN) unique to each project. All properly approved Participating Agency proposals will be stamped with
the OMNIA Partners Logo which contains a CPN and language that states the Proposal is in accordance with
Daikin Applied’s Region 4 ESC contract available via OMNIA Partners. An Agency can further verify pricing by
contacting either OMNIA Partners or Daikin directly and request a Price Verification Document for a specified CPN.
Page 12 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
6 Propose the frequency of updates to the Offeror’s pricing structure. Describe any proposed indices to
0 guide price adjustments. If offering a catalog contract with discounts by category, while changes in
individual pricing may change, the category
discounts should not change over the term of the Contract.
Labor rates are updated on annual basis. Equipment/Material pricing is typically updated on bi-annual basis.
6 Describe how future product introductions will be priced and align with Contract pricing proposed.
1
Daikin has a very active new product introduction roadmap so as new products are introduced to the market, we
will modify contract to add these products with pricing.
6 Describe any diversity programs or partners supplier does business with and how Participating
2 Agencies may use diverse partners through the Master Agreement.
Indicate how, if at all, pricing changes when using the diversity program. If there are any diversity programs, provide
a list of diversity alliances and a copy of their certifications.
At Daikin Applied, Diversity is about embracing our differences, while Inclusion is a culture of respect and
humanity. "DaikInclusion" is nurtured by Daikin’s People Centered Management (PCM), which encourages that we
take an interest in people, see their good qualities first, and “accept the nail that sticks out”. Regardless of our
differences, we strive to listen with empathy, seek to understand, admit when we don’t know, and challenge
respectfully. As outlined in our Daikin Applied Values, we are committed to creating an inclusive culture where
everyone can feel heard, valued and have a sense of belonging. We aim to create a diverse and inclusive
environment by doing the following: 1.Educate, listen, and have open dialogues. 2.Hire, retain and develop the
best talent while embracing diversity. 3.Build relationships through activities and community involvement.
6 Minority Women Business Enterprise Certification
3 If yes, list certifying agency.
No response
6 Small Business Enterprise (SBE) or Disadvantaged Business Enterprise (DBE) Certification
4 If yes, list certifying agency.
No response
6 Historically Underutilized Business (HUB) Certification
5 If yes, list certifying agency.
No response
6 Historically Underutilized Business Zone Enterprise (HUBZone) Certification
6 If yes, list certifying agency.
No response
6 Other recognized diversity certificate holder
7 If yes, list certifying agency
No response
Page 13 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
6 Describe how Supplier will transition any existing Public Agency customers’ accounts to the Master
8 Agreement available nationally through OMNIA Partners.
Include a list of current cooperative contracts (regional and national) Offeror holds and describe how the Master
Agreement will be positioned among the other cooperative agreements.
Daikin Applied will continue to promote the Master Agreement to its public customers as it does with its current
Region 4 ESC contract. Daikin Applied’s sales teams lead sales discussions with the value and benefits of
cooperative purchasing. In many cases, customers issue a purchase addendum stating all purchases between
Daikin Applied and the Public Agency must be based on Daikin Applied’s Region 4 ESC contract. Daikin Applied’s
current cooperative contracts are with the General Services Administration (GSA contracts), TIPS, CoStars, and
BuyBoard. Daikin Applied’s GSA contracts are utilized mostly with federal customers and it’s BuyBoard contract is
specific to the states of TX, NM, and AZ. GSA/BuyBoard contracts include only Daikin Applied products and labor,
which is a minimal offering to public agencies. TIPS is only utilized when an agency requests and has been used in
the South Central Region. Daikin Applied presents its Region 4 ESC Master Agreement as the lead contract
procurement vehicle; most often, GSA,TIPS or BuyBoard is provided only if the customer expresses a specific
preference for these programs. Daikin also has a number of healthcare cooperative programs.
6 Acknowledge Supplier agrees to provide its logo(s) to OMNIA Partners and agrees to provide
9 permission for reproduction of such logo in marketing communications and promotions.
Acknowledge that use of OMNIA Partners logo will require permission for reproduction, as well.
Yes
No
7 Confirm Supplier will be proactive in direct sales of Supplier’s goods and services to Public Agencies
0 nationwide and the timely follow up to leads established by OMNIA Partners.
All sales materials are to use the OMNIA Partners logo. At a minimum, the Offeror's sales initiatives should
communicate:
Master Agreement was competitively solicited and publicly awarded by a Principal Procurement Agency
Best government pricing
No cost to participate
Non-exclusive
Yes
No
7 Confirm Offeror will train its national sales force on the Master Agreement. At a minimum, sales training
1 should include:
Key features of Master Agreement
Working knowledge of the solicitation process
Awareness of the range of Public Agencies that can utilize the Master Agreement through OMNIA Partners
Knowledge of benefits of the use of cooperative contracts
Yes
No
Page 14 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
7 Provide the name, title, email and phone number for the person(s), who will be responsible for:
2
Executive Support
Marketing
Sales
Sales Support
Financial Reporting
Accounts Payable
Contracts
Executive Support: Keela Bakken, VP-National Accounts, keela.bakken@daikinapplied.com, 612-212-5500.
Marketing: Susan Kaufman, VP-Communications and Branding, susan.kaufman@daikinapplied.com, 763-203-
1679. Sales and Sales Support: Greg Coffman, National Government Cooperative Sales Manager,
greg.coffman@daikinapplied.com, 763-353-2252. Financial Reporting: Bryce Zaner, National Government
Cooperative Program Manager, bryce.zaner@daikinapplied.com, 763-203-1330. Accounts Payable: Angie
Blanchette, Director - Finance, angie.blanchette@daikinapplied.com, 763-553-5126. Contracts: Greg Coffman,
National Cooperative Sales Manager, greg.coffman@daikinapplied.com, 763-353-2252.
7 Describe in detail how Supplier’s national sales force is structured, including contact information for
3 the highest-level executive in charge of the sales team.
Daikin Applied has an executive and government team focused on growing Region 4 ESC contract sales. The key
members of the team are as follows: Name Title Team Email Yu Nishiwaki Chief Operating Officer Executive James
Moe Senior Vice President, Sales and Service Executive james.moe@daikinapplied.com John Moon Senior Vice
President, Customer Solutions/Marketing Executive David Godsil Divisional Vice President – North Division
Executive Bill Barkley Divisional Vice President – West Division Executive Sean O’Brien Divisional Vice President
- East Division Executive Keela Bakken Director of National Accounts Executive Greg Coffman National
Government Cooperative Sales Manager Government Robert Preston Contracts Compliance Manager
Government Bryce Zaner National Government Program Manager Government Shey Bauer Government
Regional Account Manager (North) Government Betsy Beach-Ross Government Regional Account Manager
(Southeast) Government Daikin Applied’s Region 4 ESC contract is and continues to be a key business focus for
Daikin Applied to significantly grow its revenue in the US market. All members of the sales team, executive and
otherwise, feel that the Region 4 ESC is a pivotal strategy for Daikin Applied to meet their growth objectives and
the majority of the team members have specific Region 4 goals built into their annual performance objectives. The
Divisional Vice Presidents are responsible for equipment, service, parts and aftermarket solutions in their
respective division. Daikin Applied goes to market through independent manufacturers reps to offer equipment
solutions, its own Daikin Applied owned service organization to offer service solutions, and parts distributors to
offer aftermarket solutions to their customers; see the attached Rep roster showing the size of Daikin Applied’s
sales force. These organizations report into the Divisional Vice Presidents as it pertains to sales and the field
service operations. They uniformly believe that Daikin Applied’s Region 4 ESC contract is a critical initiative in
growing all three (equipment, service, and aftermarket) market segments. Daikin Applied’s Government National
Accounts team is led by Greg Coffman who has been with Daikin over 2 years, and Bryce Zaner, who has been
with the government team for 8+ years. The government team follows a strict review process for all cooperative
contracting solutions to ensure contract compliance throughout the procurement process. The team continues to
market the Region 4 ESC contract, train the Daikin Applied sales teams, and educating public agencies on the
values and benefits of cooperative contracting. Daikin Applied has invested in 2 dedicated regional account
managers to focus on growing cooperative contract sales. This investment has paid dividends as seen by the
contract growth in the North Central and Southeast regions. Daikin Applied remains committed to investing in its
government team and its partnership with Region 4 ESC.
Page 15 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
7 Explain in detail how the sales teams will work with the OMNIA Partners team to implement, grow and
4 service the national program.
Daikin Applied holds strategy meetings with OMNIA Partners leadership and regional managers to identify key
states and target markets to leverage, implement, and grow national cooperative contract sales within each of
Daikin Applied’s sales divisions. Once key states and targets have been identified by region, a sales initiative
tailored to their unique area, legislative climate, and market will be developed. After development, training, and
rollout, programs will be held to educate and train Daikin Applied’s sales teams. Daikin Applied has implemented a
training and education strategy to identify low performers and opportunity rich regions to hold additional focused
training for its sales teams. We have developed a specific initiative for the West region based on leads from
Connect and education on agency familiarity and acceptance of coops. An OMNIA Partners business plan will be
created for each awarded year of the new contract which addresses training. Daikin Applied encourages its sales
teams to bring their local OMNIA Partners regional manager into customer discussions to assist in procurement
discussions. Daikin Applied notifies OMNIA Partners leadership when Daikin Applied encounters legislative issues
which prevent the use of cooperative purchasing so OMNIA Partners can work to resolve these issues. We have
worked with OMNIA and their Reps in Ohio, New York, Louisiana, California, and Oregon.
7 Explain in detail how Offeror will manage the overall national program throughout the term of the
5 Master Agreement, including ongoing coordination of marketing and sales efforts, timely new
Participating Public Agency account set-up, timely contract
administration, etc.
Daikin Applied’s government team follows a strict review process of all cooperative contracting solutions to ensure
contract compliance throughout the procurement process. The team continues to market the Region 4 ESC
Requirements for National Cooperative Contract, train the Daikin Applied sales teams, and educating public
agencies on the values and benefits of cooperative contracting. The government team, which is part of Daikin
Applied’s National Accounts, has developed a National Accounts Guide which includes a specific section on
Cooperative Contracting which clearly states the compliance requirements of Daikin Applied’s Region 4 ESC
Master Agreement. The government team also intends to meet with Daikin Applied and OMNIA’s business
development manager, contract compliance manager, and marketing teams monthly to coordinate efforts which will
target specific public agency and contract offerings throughout the year. The government team also has a contract
compliance manager who oversees all contract modifications working directly with OMNIA Partners. Daikin Applied
has continually updated its contract with Region 4 ESC and has not had any contract violations with the 2020
award. We have added additional resources to our government team for order faster processing, CPN and
proposal compliance, accounting, and improved accuracy and reporting to OMNIA.
7 State the amount of Supplier’s Public Agency sales for the previous fiscal year. Provide a list of
6 Supplier's top 10 Public Agency customers, the total purchases for each for the previous fiscal year
along with a key contact for each.
Daikin Applied’s estimated sales for Public Agencies in calendar year 2023 totaled $626,100,071.81. The ten (10)
largest Public Agency customers for Daikin Applied, including estimated sales totals, are Henry County
($9,349,940.11)-Shey Bauer, Houston Independent School District ($3,764,555,41)-Kimberly Shepherd, Fort
Bragg ($3,742,858.74)-Rick Pennington, Hillsborough County Schools ($3,188,371.32)-Ruben Colon, Gahanna
Jefferson HS ($2,980,275.64)-Mark Lockwood, Cuyahoga Falls Schools ($2,839,475.71)-Eric Swain, Corpus
Christi ISD ($2,696,000.20)-Thomas Bailey, University of Mary Washington ($2,545,753.73)-Stephen Colwell,
Chesterfield County Public Schools ($2,418,455.90)-Brandon Corr, and Broward County School Board
($2,403,825.00)-Ruben Colon
7 Year 1 - Provide the Contract Sales (as defined in Section 12 of OMNIA Partners Administration
7 Agreement) that Supplier will guarantee each year under the Master Agreement for the initial three
years of the Master Agreement ("Guaranteed Contract Sales").
To the extent Supplier guarantees minimum Contract Sales, the Administrative Fee shall be calculated based on the
greater of the actual Contract Sales and the Guaranteed Contract Sales.
$172000000.00
Page 16 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
7 Year 2 - Provide the Contract Sales (as defined in Section 12 of OMNIA Partners Administration
8 Agreement) that Supplier will guarantee each year under the Master Agreement for the initial three
years of the Master Agreement
To the extent Supplier guarantees minimum Contract Sales, the Administrative Fee shall be calculated based on the
greater of the actual Contract Sales and the Guaranteed Contract Sales.
$198000000.00
7 Year 3 - Provide the Contract Sales (as defined in Section 12 of OMNIA Partners Administration
9 Agreement) that Supplier will guarantee each year under the Master Agreement for the initial three
years of the Master Agreement
To the extent Supplier guarantees minimum Contract Sales, the Administrative Fee shall be calculated based on the
greater of the actual Contract Sales and the Guaranteed Contract Sales.
$228000000.00
8 Please download and thoroughly review the Scope of Work, located on the Attachments Tab. Indicate
0 your review and acceptance.
Yes
8 Oral Communications concerning this RFP shall not be binding and shall in no way excuse an Offeror of
1 the obligations set forth in this proposal.
Yes
8 Please download and thoroughly review the Terms and Conditions, located on the Attachments Tab.
2 Indicate your review and acceptance.
Yes
Page 17 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
8 Products/Pricing - Upload on Response Attachments Tab
3 i. Offerors shall provide pricing based on coefficient pricing completing Appendix D; or on a discount from a
manufacturer’s or other price list or catalog, or fixed price, or a combination of both with indefinite quantities. Prices
listed will be used to establish the extent of a manufacturer’s product lines, services, warranties, etc. that are
available from Offeror and the pricing per item. Multiple percentage discounts are acceptable if, where different
percentage discounts apply, the different percentages are specified. Additional pricing and/or discounts may be
included. Products and services proposed are to be priced separately with all ineligible items identified. Discounts
proposed shall remain the same throughout the term of the contract and at all renewal options. At a minimum the
Awarded Offeror must hold the proposed price list firm for the first 12 months after the contract award. Offerors may
elect to limit their proposals to any category or categories.
ꞏ Complete the applicable Pricing information
o Provide equipment manufacturer, equipment types and discount off published list price.
o Define any freight charges.
o Provide classifications of labor with billable rates for each respondent’s office(s), territories or district(s) along with
any sub-office pricing as required. Each of these labor classification rates shall be fully burdened, defined and will
be set for Normal Working Hours and Non-Normal Working Hours. Sub-contractor labor shall not be recognized.
Each respondent shall determine their sub-contractor’s labor rate as a prime labor classification. For example, an
electrician’s labor rate shall be calculated based on the respondent’s sub-contractor’s labor billable rate plus
respondent’s normal margins on sub-contractor labor. Labor classification shall be provided in the response.
o If using coefficient pricing, the Normal Working Hours and Non-Normal Working Hours for tasks identified in the
Scope of Work shall use a benchmark against an established data set (e.g.; RSMeans or others) to ensure that the
hours provided can be verified. Each of these hourly tasks shall have a coefficient of labor against an established
data set (e.g.; RSMeans or others) city cost index by each respondent’s office(s), territories or district(s) to
determine effectiveness of providing these tasks. Offerors using coefficient pricing will complete Appendix D.
Federal Funding Pricing: Due to products and services potentially being used in response to an emergency or
disaster recovery situation in which federal funding may be applied, provide alternative pricing that does not include
cost plus a percentage of cost or pricing based on time and materials; if time and materials is necessary, a ceiling
price that the contract exceeds at its own risk will be needed. Products and services provided in a situation where
an agency is eligible for federal funding, Offeror is subject to and must comply with all federal requirements
applicable to the funding including, but not limited to the FEMA Special Conditions section located in the Federal
Funds Certifications Exhibit F.
8 Not to Exceed Pricing
4 Region 4 ESC requests pricing be submitted as not to exceed pricing. Unlike fixed pricing, the Contractor can adjust
submitted pricing lower if needed but, cannot exceed original pricing submitted. Contractor must allow for lower
pricing to be available for similar product and service purchases. Cost plus pricing as a primary pricing structure is
not acceptable.
8 Provide the number, size and location of Supplier’s distribution facilities, warehouses and retail
5 network as applicable.
Daikin has factories across US and Mexico to support our customers totalling over 2.8M square feet. We have
parts warehouses in Dayton, OH and Las Vegas, Nevada.
Page 18 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
8 Provide a detailed ninety-day plan beginning from award date of the Master Agreement describing the
6 strategy to immediately implement the Master Agreement as supplier’s primary go to market strategy for
Public Agencies to supplier’s teams nationwide,
to include, but not limited to:
i. Executive leadership endorsement and sponsorship of the award as the public sector go-to-market strategy
within first 10 days
ii. Training and education of Supplier’s national sales force with participation from the Supplier’s executive
leadership, along with the OMNIA Partners team within first 90 days
Within ten days of award notice, Daikin Applied will announce the award via multiple media sources (i.e. LinkedIn,
Facebook, internal marketing news). Daikin Applied’s national sales and service force, including its independent
Reps and Service Alliance Partners, will be made aware, through internal marketing news, of the award which
would extend Daikin Applied’s current 5-year contract with Region 4 ESC. Daikin Applied is focused on training
and educating its Daikin Applied and independent representative sales force. All new service sales personnel are
provided the OMNIA overview webinar, power points, and our co-branded K-12 initiative brochure available on our
sales portal. We have also identified the need to train all new sales coordinators and have done so for more than
a year, which will continue. Daikin Applied will implemented a training strategy within 90 days, with the input of
OMNIA Partners, to identify key cooperative markets and regions to hold additional focused training for its sales
teams and regional leadership. We will also identify Rep and Service teams that have not grown or have minimal
cooperative sales and develop a sales strategy by engaging the OMNIA Reps, signing up Daikin sales personnel
on OMNIA Connect, and providing qualified leads from which to begin developing strategic partnerships. The
training will include monthly follow-up to measure and ensure progress. An OMNIA Partners business plan will be
created for each awarded year of the new contract as well as holding a Business Advancement Meeting with
OMNIA annually.
Page 19 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
8 Provide a detailed ninety-day plan beginning from award date of the Master Agreement describing the
7 strategy to market the Master Agreement to current Participating Public Agencies, existing Public
Agency customers of Supplier, as well as to prospective
Public Agencies nationwide immediately upon award, to include, but not limited to:
i. Creation and distribution of a co-branded press release to trade publications
ii. Announcement, Master Agreement details and contact information published on the Supplier’s website within first
90 days
iii. Design, publication and distribution of co-branded marketing materials within first 90 days
iv. Commitment to attendance and participation with OMNIA Partners at national (i.e. NIGP Annual Forum, NPI
Conference, etc.), regional (i.e. Regional NIGP Chapter Meetings, Regional Cooperative Summits, etc.) and
supplier-specific trade shows, conferences and meetings throughout the term of the Master Agreement
v. Commitment to attend, exhibit and participate at the NIGP Annual Forum in an area reserved by OMNIA Partners
for partner suppliers. Booth space will be purchased and staffed by Supplier. In addition, Supplier commits to
provide reasonable assistance to the overall promotion and marketing efforts for the NIGP Annual Forum, as
directed by OMNIA Partners.
vi. Design and publication of national and regional advertising in trade publications throughout the term of the
Master Agreement
vii. Ongoing marketing and promotion of the Master Agreement throughout its term (case studies, collateral pieces,
presentations, promotions, etc.)
viii. Dedicated OMNIA Partners internet web-based homepage on Supplier’s website with:
• OMNIA Partners standard logo;
• Copy of original Request for Proposal;
• Copy of Master Agreement and amendments between Principal Procurement Agency and Supplier;
• Summary of Products and pricing;
• Marketing Materials
• Electronic link to OMNIA Partners’ website including the online registration page;
• A dedicated toll-free number and email address for OMNIA Partners
i: An OMNIA Partners business plan will be created for each awarded year of the new contract. Marketing will
include cobranded press releases via multiple social media platforms along with trade publications which OMNIA
Partners assists Daikin Applied with advertisements. ii: Daikin Applied will update its current dedicated cooperative
website within DaikinApplied.com with newly awarded contract information within the first 90 days of award. iii:
Daikin Applied currently co-brands marketing materials with its Region 4 ESC contract available through OMNIA
Partners and intends to continue to co-brand materials under this contact similar to our K-12 brochure. iv: Daikin
Applied is committed to attend supplier-specific trade shows, conferences, and meetings as reasonably scheduled
and within Daikin Applied’s budget throughout the term of the Master Agreement. v: Daikin Applied is committed to
attend, exhibit and participate at the NIGP Annual Forum in the area reserved by OMNIA Partners as well as
participating in other reasonably requested events which are budgeted by Daikin Applied. vi: Daikin Applied
agrees to this requirement as approved by both companies. Daikin Applied in collaboration with OMNIA Partners
will advertise in national and regional trade publications to support national and regional activities, in addition to
leveraging the rep network to disseminate messages. Recently Daikin had co-branded banner ads as well as a
national article published in NCPP magazine highlighting our Garrett County project through OMNIA. vii: Daikin
agrees to this request. viii: Daikin Applied agrees to the requirements listed above. Upon successful award, Daikin
Applied will update its current OMNIA Partners, Public Sector internet web-based homepage on both Daikin
Applied and OMNIA websites.
8 GENERAL TERMS AND CONDITIONS
8 Respondent agrees to comply with the Contract and General Terms and Conditions provided as an attachment to
this online bid event. Any deviations to the Contract and General Terms and Conditions may be provided using the
procedures set forth in the attribute pertaining to deviations.
I certify compliance with this attribute.
Page 20 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
8 DEVIATIONS TO TERMS AND CONDITIONS
9 Any Deviation from the RFP documents, including the General Terms and Conditions, Notice to Offeror, or any other
document presented with terms for consideration by the proposer MUST be documented and presented on the
Deviation Form and attached to this electronic bid event via an electronic upload to the "Response Attachments"
tab. In addition to indicating the requested deviations on the form, additional pages may be provided to more
thoroughly explain each deviation listed on the Deviation Form.
I certify compliance with this attribute.
9 FELONY CONVICTION NOTIFICATION
0 State of Texas Legislative Senate Bill No. 1 Section 44.034, Notification of Criminal History, Subsection (a), states “a
person or business entity that enters into an agreement with a school district must give advance notice to the
district if the person or an owner or operator of the business entity has been convicted of a felony. The notice must
include a general description of the conduct resulting in the conviction of a felony”.
Subsection (b) states “a school district may terminate the agreement with a person or business entity if the district
determines that the person or business entity failed to give notice as required by Subsection (a), or misrepresented
the conduct resulting in the conviction. The district must compensate the person or business entity for services
performed before the termination of the contract”.
Subsection (c) states “this section does not apply to a publicly held corporation”.
Use the list of values associated with this item to identify your status as it relates to this legal requirement.
Non-Felon - person/owner IS NOT a convicted felon
9 NAME OF FELON AND NATURE OF FELONY, IF APPLICABLE
1 If response to previous attribute was "Felon - person/owner IS a convicted felon", vendor shall give the name of the
felon and details of conviction.
If you did not answer "Felon - person/owner IS a convicted felon" in the previous question, type "N/A" in the
respective field.
N/A - Not Applicable.
9 CRIMINAL HISTORY RECORDS REVIEW OF CERTAIN CONTRACT EMPLOYEES
2 Texas Education Code Chapter §22.0834 requires that criminal history records be obtained regarding covered
employees of entities that contract with a school entity in Texas to provide services for that school entity
(“Contractors”) and entities that contract with school entity contractors (“Subcontractors”). Covered employees with
disqualifying criminal histories are prohibited from serving at a school entity. Contractors/Subcontractors contracting
with a school entity shall (1) maintain compliance with the requirements of Texas Education Code Chapter 22 to the
school entity; and (2) require that each of their subcontractors complies with the requirements of Texas Education
Code Chapter 22. Contractors performing work at a school entity in Texas must comply with these statutes.
Compliance includes providing or causing employees and sub-contractor employees to provide
requested information and fingerprinting upon request.
Covered employees: Employees of a Contractor/Subcontractor who have or will have continuing duties related to
the service to be performed at a school entity and have or will have direct contact with students. The school entity
will be the final arbiter of what constitutes continuing duties and direct contact with students at their school.
I certify compliance with this attribute.
Page 21 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
9 HISTORICALLY UNDERUTILIZED BUSINESS (HUB) CERTIFICATION
3 Businesses that have been certified by the Texas Building and Procurement Commission (TBPC) or other qualified
agency as Historically Underutilized Business (HUB) entities are encouraged to indicate their HUB status when
responding to this proposal invitation. The electronic catalogs will indicate HUB certifications for vendors that
properly indicate and document their HUB certification on this form.
Select one of the available options:
OPTION A: My business has NOT been certified as HUB.
OPTION B: I certify that my business has been certified as a Historically Underutilized Business (HUB), and I
have/will upload the certification information into the "Response Attachments" Tab located in this online bidding
event.
OPTION A - Not HUB
9 DISCLOSURE OF INTERESTED PARTIES
4 Texas state law requires the Disclosure of Interested Parties be filed with a public entity, including regional service
centers and school districts, for any contract which:
(1) requires an action or vote by the governing body; or
(2) has a value of $1 million or more; or
(3) for any services provided that would require an individual to register as a lobbyist under TX Gov’t Code Chapter
305.
NOTE: This form is not required if the vendor is a publicly-traded business entity, including a wholly-owned
subsidiary of the business entity (a company in which ownership is dispersed among the general public via shares
of stock which are traded via at least one stock exchange or over-the-counter market).
If you are required by law to submit this form, it must be completed online at the Texas Ethics Commission website.
Obtain a numbered certificate and click the link below to access the instructions and to complete this required form.
Upon completion, vendors required to submit the form must attach it to the proposal via the "Response
Attachments" Tab.
Click here to complete the form on the Texas Ethic Commission's 1295 Form webpage.
Please note: The District must verify receipt of all required 1295 forms received within 30 days on the Texas Ethics
Commission website. This verification does not indicate a contract award. Contract awards will be issued via direct
communication from the AISD Purchasing Department. A contract requiring a Disclosure of Interested Parties form is
voidable at any time if:
(1) the governmental entity or state agency submits to the business entity written notice of the business entity's
failure to provide the required disclosure; and
(2) the business entity fails to submit to the governmental entity or state agency the required disclosure on or
before the 10th business day after the date the business entity receives the written notice.
IF UNDER LAW YOU ARE EXEMPT FROM SUBMITTING THIS 1295 FORM, PROPOSERS MUST SUBMIT A
DOCUMENT THAT SHOWS PROOF OR PROVIDES EXPLANATION OF THIS EXEMPTION.
THE FOLLOWING CONTRACTS ARE EXEMPT FROM THE REQUIREMENTS OF TEXAS DISCLOSURE OF
INTERESTED PARTIES LAWS:
• a sponsored research contract of an institution of higher education;
• an interagency contract of a state agency or an institution of higher education;
• a contract related to health and human services if:
• the value of the contract cannot be determined at the time the contract is executed; and
• any qualified vendor is eligible for the contract;
• a contract with a publicly traded business entity, including a wholly owned subsidiary of the business entity;
• a contract with an electric utility, as that term is defined by Section 31.002, Utilities Code; or
• a contract with a gas utility, as that term is defined by Section 121.001, Utilities Code.
I certify compliance with this attribute.
Page 22 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
9 CONFLICT OF INTEREST QUESTIONNAIRE
5 Region 4 Education Service Center (Region 4) is required to comply with Texas Local Government Code Chapter
176, Disclosure of Certain Relationships with Local Government Officers. House Bill 23 significantly changed
Chapter 176 as well as the required disclosures and the corresponding forms. As of September 1, 2015, any
vendor who does business with Region 4 or who seeks to do business with Region 4 must fill out the new Conflict of
Interest Questionnaire (CIQ) if a conflict of interest exists. A conflict of interest exists in the following situations:
1) If the vendor has an employment or other business relationship with a local government officer of Region 4 or a
family member of the officer, as described by section 176.003(a)(2)(A) of the Texas Local Government Code; or
2) If the vendor has given a local government officer of Region 4, or a family member of the officer, one or more
gifts with the aggregate value of $100, excluding any gift accepted by the officer or a family member of the officer if
the gift is: (a) a political contribution as defined by Title 15 of the Election Code; or (b) a gift of food accepted as a
guest; or
3) If the vendor has a family relationship with a local government officer of Region 4.
“Vendor” means a person who enters or seeks to enter into a contract with a local governmental entity. The term includes an agent of a vendor. The term
includes an officer or employee of a state agency when that individual is acting in a private capacity to enter into a contract. The term does not include a
state agency except for Texas Correctional Industries. Texas Local Government Code 176.001(7).
“Business relationship” means a connection between two or more parties based on commercial activity of one of the parties. The term does not include a
connection based on: (A) a transaction that is subject to rate or fee regulation by a federal, state, or local governmental entity or an agency of a federal,
state, or local governmental entity; (B) a transaction conducted at a price and subject to terms available to the public; or (C) a purchase or lease of goods or
services from a person that is chartered by a state or federal agency and that is subject to regular examination by, and reporting to, that agency. Texas Local
Government Code 176.001(3).
“Family relationship” means a relationship between a person and another person within the third degree by consanguinity or the second degree by affinity,
as those terms are defined by Subchapter B, Chapter 573, Government Code. Texas Local Government Code 176.001(2-a).
“Local government officer” means: (A) a member of the governing body of a local governmental entity; (B) a director, superintendent, administrator,
president, or other person designated as the executive officer of a local governmental entity; or (C) an agent of a local governmental entity who exercises
discretion in the planning, recommending, selecting, or contracting of a vendor. Texas Local Government Code 176.001(4).
Individuals serving as a Member of the Board of Directors, the Executive Director, Cabinet Members,
and other local government officers may be found at: https://www.esc4.net/about/about-region-4.
For additional information on Conflict of Interest Questionnaire, and the statutes that mandate it, please visit the
following links:
Texas Local Government Code, Section 176
Texas House Bill 23
A blank Conflict of Interest Questionnaire is available by clicking:
https://www.ethics.state.tx.us/data/forms/conflict/CIQ.pdf.
If your firm is required to return a completed Conflict of Interest Questionnaire with your proposal submission, use
the "Response Attachments" Tab to upload the completed document.
I certify compliance with this attribute.
Page 23 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
9 ENTITITES THAT BOYCOTT ISRAEL
6 Pursuant to Chapter 2271 of the Texas Government Code, the Respondent hereby certifies and verifies that neither
the Respondent , nor any affiliate, subsidiary, or parent company of the Respondent , if any (the “Respondent
Companies”), boycotts Israel, and the Respondent agrees that the Respondent and Respondent Companies will not
boycott Israel during the term of this Agreement. For purposes of this Agreement, the term “boycott” shall mean and
include refusing to deal with, terminating business activities with, or otherwise taking any action that is intended to
penalize, inflict economic harm on, or limit commercial relations with Israel, or with a person or entity doing business
in Israel or in an Israeli-controlled territory, but does not include an action made for ordinary business purposes.
EXCEPTIONS: Clause only applies to contracts and contractors that meet the following criteria: (i) Respondent is not a sole proprietorship; (ii) with 10 or
more full-time employees; and (iii) with a contract to be paid a value of $100,000 or more wholly or partially from public funds of the governmental entity.
I certify compliance with this attribute.
9 FOREIGN TERRORIST ORGANIZATIONS
7 Section 2252.152 of the Texas Government Code prohibits Region 4 ESC from awarding a contract to any person
who does business with Iran, Sudan, or a foreign terrorist organization as defined in Section 2252.151 of the Texas
Government Code. Respondent certifies that it not ineligible to receive the contract.
I certify compliance with this attribute.
9 FIREARMS ENTITIES AND TRADE ASSOCIATIONS DISCRIMINATION
8 Respondent verifies that: (1) it does not, and will not for the duration of the contract, have a practice, policy,
guidance, or directive that discriminates against a firearm entity or firearm trade association or (2) the verification
required by Section 2274.002 of the Texas Government Code does not apply to the contract. If circumstances
relevant to this provision change during the course of the contract, Respondent shall promptly notify Region 4 ESC.
APPLICABILITY: This clause applies only to a contract that: (1) is between a governmental entity and a company with at least 10 full-time employees; and
(2) has a value of at least $100,000 that is paid wholly or partly from public funds of the governmental entity.
EXCEPTIONS: This clause is not required when a state Agency: (1) contracts with a sole-source provider; or (2) does not receive any bids from a company
that is able to provide the written verification required by Section 2274.002(b) of the Texas Government Code.
I certify compliance with this attribute.
9 ENERGY COMPANY BOYCOTT PROHIBITED
9 Respondent represents and warrants that: (1) it does not, and will not for the duration of the contract, boycott
energy companies or (2) the verification required by Section 2274.002 of the Texas Government Code does not
apply to the contract. If circumstances relevant to this provision change during the course of the contract,
Respondent shall promptly notify Region 4 ESC.
EXCEPTIONS: Clause only applies to contracts and contractors that meet the following criteria: (i) a “company” within the definitions of Section
2274.001(2) of the Tex. Gov’t Code; (ii) with 10 or more full-time employees; and (iii) with a contract to be paid a value of $100,000 or more wholly or
partially from public funds of the governmental entity.
I certify compliance with this attribute.
1 CRITICAL INFRASTRUCTURE AFFIRMATION
0 Pursuant to Government Code Section 2274.0102, Respondent certifies that neither it nor its parent company, nor
0
any affiliate of Respondent or its parent company, is: (1) majority owned or controlled by citizens or governmental
entities of China, Iran, North Korea, Russia, or any other country designated by the Governor under Government
Code Section 2274.0103, or (2) headquartered in any of those countries.
EXCEPTION: Clause only applies to solicitations and contracts in which the contractor would be granted direct or remote access to or control of critical
infrastructure, as defined by Section 2274.0101 of the Texas Government Code, in this state, other than access specifically allowed for product warranty
and support purposes.
The Governor of the State of Texas may designate countries as a threat to critical infrastructure under Section 2274.0103 of the Texas Government Code.
Agencies should promptly add any country that is designated by the Governor to this clause.”
I certify compliance with this attribute.
Page 24 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 OPEN RECORDS POLICY
0 All proposals, information and documents submitted are subject to the Public Information Act requirements
1
governed by the State of Texas once a Contract(s) is executed. If an Offeror believes its response, or parts of its
response, may be exempted from disclosure, the Offeror must specify page-by-page and line-by-line the parts of
the response, which it believes, are exempt and include detailed reasons to substantiate the exemption. Price is not
confidential and will not be withheld. Any unmarked information will be considered public information and released, if
requested under the Public Information Act.
The determination of whether information is confidential and not subject to disclosure is the duty of the Office of
Attorney General (OAG). Region 4 ESC must provide the OAG sufficient information to render an opinion and
therefore, vague and general claims to confidentiality by the Offeror are not acceptable. Region 4 ESC must comply
with the opinions of the OAG. Region 4 ESC assumes no responsibility for asserting legal arguments on behalf of
any Offeror. Offeror is advised to consult with their legal counsel concerning disclosure issues resulting from this
procurement process and to take precautions to safeguard trade secrets and other proprietary information.
Check one of the following responses to the Acknowledgment and Acceptance of Region 4 ESC’s Open Records
Policy below:
OPTION A: We acknowledge Region 4 ESC’s Open Records Policy and declare that no information submitted with
this proposal, or any part of our proposal, is exempt from disclosure under the Public Information Act.
OPTION B: We declare the following information to be a trade secret or proprietary and exempt from disclosure
under the Public Information Act and these requested exemptions are uploaded into the "Response Attachments"
Tab located in this online bidding event.
(Note: Offeror must specify page-by-page and line-by-line the parts of the response, which it believes, are exempt.
In addition, Offeror must include detailed reasons to substantiate the exemption(s). Price is not confidential and will
not be withheld. All information believed to be a trade secret or proprietary must be listed. It is further understood
that failure to identify such information, in strict accordance with the instructions, will result in that information being
considered public information and released, if requested under the Public Information Act.)
OPTION B - Proprietary information marked
1 CONSENT TO RELEASE PROPOSAL TABULATION
0 Notwithstanding anything explicitly and properly declared as Confidential or Proprietary Information to the contrary,
2
by submitting a Proposal, Vendor consents and agrees that, upon Contract award, the District may publicly release,
including posting on the public Region 4 ESC and/or OMNIA Partners website(s), a copy of the proposal tabulation
for the Contract including Vendor name; proposed catalog/pricelist name(s); proposed percentage discount(s), unit
price(s), hourly labor rate(s), or other specified pricing; and Vendor award notice information.
I certify compliance with this attribute.
Page 25 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 CONTRACTING INFORMATION
0 If Vendor is not a governmental body and
3
(a) this Agreement has a stated expenditure of at least $1 million in public funds for the purchase of goods or
services by REGION 4 ESC; or
(b) this Agreement results in the expenditure of at least $1 million in public funds for the purchase of goods or
services by REGION 4 ESC in a fiscal year of REGION 4 ESC, the following certification shall apply;
otherwise, this certification is not required.
As required by Tex. Gov’t Code § 552.374(b), the following statement is included in the RFP and the Agreement
(unless the Agreement is
(1) related to the purchase or underwriting of a public security;
(2) is or may be used as collateral on a loan; or
(3) proceeds from which are used to pay debt service of a public security of loan):
“The requirements of Subchapter J, Chapter 552, Government Code, may apply to this RFP and Agreement and
the contractor or vendor agrees that the contract can be terminated if the contractor or vendor knowingly or
intentionally fails to comply with a requirement of that subchapter.”
Pursuant to Subchapter J, Chapter 552, Texas Government Code, the Vendor hereby certifies and agrees to
(1) preserve all contracting information related to this Agreement as provided by the records retention
requirements applicable to REGION 4 ESC for the duration of the Agreement;
(2) promptly provide to REGION 4 ESC any contracting information related to the Agreement that is in the
custody or possession of the Vendor on request of REGION 4 ESC; and
(3) on completion of the Agreement, either
(a) provide at no cost to AISD all contracting information related to the Agreement that is in the custody
or possession of Vendor, or
(b) preserve the contracting information related to the Agreement as provided by the records retention
requirements applicable to REGION 4 ESC.
I certify compliance with this attribute.
1 ANTI-TRUST CERTIFICATION STATEMENT
0 Vendor affirms under penalty of perjury of the laws of the State of Texas that:
4
(1) I am duly authorized to execute this contract on my own behalf or on behalf of the company, corporation,
firm, partnership or individual (Company) listed below;
(2) In connection with this bid, neither I nor any representative of the Company have violated any provision of
the Texas Free Enterprise and Antitrust Act, Tex. Bus. & Comm. Code Chapter 15;
(3) In connection with this bid, neither I nor any representative of the Company have violated any federal
antitrust law; and
(4) Neither I nor any representative of the Company have directly or indirectly communicated any of the
contents of this bid to a competitor of the Company or any other company, corporation, firm, partnership or
individual engaged in the same line of business as the Company.
I certify compliance with this attribute.
1 FEDERAL RULE (A) - CONTRACT TERM VIOLATIONS
0 (A) Contracts for more than the simplified acquisition threshold currently set at $250,000 (2 CFR §200.320), which
5
is the inflation adjusted amount determined by the Civilian Agency Acquisition Council and the Defense Acquisition
Regulations Council (Councils) as authorized by 41 U.S.C. 1908, must address administrative, contractual, or legal
remedies in instances where contractors violate or breach contract terms, and provide for such sanctions and
penalties as appropriate.
Pursuant to Federal Rule (A) above, when federal funds are expended by Region 4 ESC, Region 4 ESC reserves
all rights and privileges under the applicable laws and regulations with respect to this procurement in the event of
breach of contract by either party.
I certify compliance with this attribute.
Page 26 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 FEDERAL RULE (B) - TERMINATION CONDITIONS
0 (B) Termination for cause and for convenience by the grantee or subgrantee including the manner by which it will
6
be effected and the basis for settlement. (All contracts in excess of $10,000)
Pursuant to Federal Rule (B) above, when federal funds are expended by REGION 4 ESC, REGION 4
ESC reserves the right to immediately terminate any agreement in excess of $10,000 resulting from this
procurement process in the event of a breach or default of the agreement by Vendor, in the event vendor fails to:
(1) meet schedules, deadlines, and/or delivery dates within the time specified in the procurement solicitation,
contract, and/or a purchase order; (2) make any payments owed; or (3) otherwise perform in accordance with the
contract and/or the procurement solicitation; (4) to the greatest extent authorized by law, if an award no longer
effectuates the program goals or priorities of the Federal awarding agency or REGION 4 ESC. REGION 4 ESC also
reserves the right to terminate the contract immediately, with written notice to vendor, for convenience, if REGION 4
ESC believes, in its sole discretion that it is in the best interest of REGION 4 ESC to do so. The vendor will be
compensated for work performed and accepted and goods accepted by REGION 4 ESC as of the termination date
if the contract is terminated for convenience of REGION 4 ESC. Any award under this procurement process is not
exclusive and REGION 4 ESC reserves the right to purchase goods and services from other vendors when it is in
the best interest of REGION 4 ESC.
I certify compliance with this attribute.
1 FEDERAL RULE (C) - EQUAL EMPLOYMENT OPPORTUNITY
0 (C) Except as otherwise provided under 41 CFR Part 60, all contracts that meet the definition of “federally assisted
7
construction contract” in 41 CFR Part 60-1.3 must include the equal opportunity clause provided under 41 CFR 60-
1.4(b), in accordance with Executive Order 11246, “Equal Employment Opportunity” (30 FR 12319, 12935, 3 CFR
Part, 1964-1965 Comp., p. 339), as amended by Executive Order 11375, “Amending Executive Order 11246
Relating to Equal Employment Opportunity,” and implementing regulations at 41 CFR part 60, “Office of Federal
Contract Compliance Programs, Equal Employment Opportunity, Department of Labor.”
It is the policy of REGION 4 ESC not to discriminate on the basis of race, color, national origin, gender, limited
English proficiency or disabling conditions in its programs. Vendor agrees not to discriminate against any employee
or applicant for employment to be employed in the performance of this Contract, with respect to hire, tenure, terms,
conditions and privileges of employment, or a matter directly or indirectly related to employment, because of age
(except where based on a bona fide occupational qualification), sex (except where based on a bona fide
occupational qualification) or race, color, religion, national origin, or ancestry. Vendor further agrees that every
subcontract entered into for the performance of this Contract shall contain a provision requiring non-discrimination
in employment herein specified binding upon each subcontractor. Breach of this covenant may be regarded as a
material breach of the Contract.
Pursuant to Federal Rule (C) and the requirements stated above, when federal funds are expended by REGION 4
ESC on any federally assisted construction contract, the equal opportunity clause is incorporated by reference
herein.
I certify compliance with this attribute.
Page 27 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 FEDERAL RULE (D) - DAVIS BACON ACT/COPELAND ACT
0 (D) Davis-Bacon Act, as amended (40 U.S.C. 3141-3148). When required by Federal program legislation, all prime
8
construction contracts in excess of $2,000 awarded by non-Federal entities must include a provision for compliance
with the Davis-Bacon Act (40 U.S.C. 3141-3144, and 3146- 3148) as supplemented by Department of Labor
regulations (29 CFR Part 5, “Labor Standards Provisions Applicable to Contracts Covering Federally Financed and
Assisted Construction”). In accordance with the statute, contractors must be required to pay wages to laborers and
mechanics at a rate not less than the prevailing wages specified in a wage determination made by the Secretary of
Labor. In addition, contractors must be required to pay wages not less than once a week. The non-Federal entity
must place a copy of the current prevailing wage determination issued by the Department of Labor in each
solicitation. The decision to award a contract or subcontract must be conditioned upon the acceptance of the wage
determination. The non-Federal entity must report all suspected or reported violations to the Federal awarding
agency. The contracts must also include a provision for compliance with the Copeland “Anti-Kickback” Act (40
U.S.C. 3145), as supplemented by Department of Labor regulations (29 CFR Part 3, “Contractors and
Subcontractors on Public Building or Public Work Financed in Whole or in Part by Loans or Grants from the United
States”). The Act provides that each contractor or subrecipient must be prohibited from inducing, by any means,
any person employed in the construction, completion, or repair of public work, to give up any part of the
compensation to which he or she is otherwise entitled. The non-Federal entity must report all suspected or reported
violations to the Federal awarding agency.
Pursuant to Federal Rule (D) above, when federal funds are expended by REGION4 ESC, during the term of an
award for all contracts and subgrants for construction or repair, the vendor will be in compliance with all applicable
Davis-Bacon Act provisions.
I certify compliance with this attribute.
1 FEDERAL RULE (E) - CONTRACT WORK HOURS AND SAFETY STANDARDS ACT
0 (E) (40 U.S.C. 3701-3708). Where applicable, all contracts awarded by the non-Federal entity in excess of
9
$100,000 that involve the employment of mechanics or laborers must include a provision for compliance with 40
U.S.C. 3702 and 3704, as supplemented by Department of Labor regulations (29 CFR Part 5). Under 40 U.S.C.
3702 of the Act, each contractor must be required to compute the wages of every mechanic and laborer on the
basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that
the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked
in excess of 40 hours in the work week. The requirements of 40 U.S.C. 3704 are applicable to construction work
and provide that no laborer or mechanic must be required to work in surroundings or under working conditions
which are unsanitary, hazardous or dangerous. These requirements do not apply to the purchases of supplies or
materials or articles ordinarily available on the open market, or contracts for transportation or transmission of
intelligence.
Pursuant to Federal Rule (E) above, when federal funds are expended by REGION 4 ESC, the vendor certifies that
during the term of an award for all contracts by REGION 4 ESC resulting from this procurement process, the vendor
will be in compliance with all applicable provisions of the Contract Work Hours and Safety Standards Act.
I certify compliance with this attribute.
1 FEDERAL RULE (F) - RIGHTS TO INVENTIONS MADE UNDER A CONTRACT OR AGREEMENT
1 (F)If the Federal award meets the definition of “funding agreement” under 37 CFR §401.2 (a) and the recipient or
0
subrecipient wishes to enter into a contract with a small business firm or nonprofit organization regarding the
substitution of parties, assignment or performance of experimental, developmental, or research work under that
“funding agreement,” the recipient or subrecipient must comply with the requirements of 37 CFR Part 401, “Rights
to Inventions Made by Nonprofit Organizations and Small Business Firms Under Government Grants, Contracts and
Cooperative Agreements,” and any implementing regulations issued by the awarding agency.
Pursuant to Federal Rule (F) above, when federal funds are expended by REGION 4 ESC, the vendor certifies that
during the term of an award for all contracts by REGION 4 ESC resulting from this procurement process, the vendor
agrees to comply with all applicable requirements as referenced in Federal Rule (F) above.
I certify compliance with this attribute.
Page 28 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 FEDERAL RULE (G) - CLEAN AIR ACT/FEDERAL WATER POLLUTION CONTROL ACT
1 (G) The Clean Air Act (42 U.S.C. 7401-7671q.) and the Federal Water Pollution Control Act (33 U.S.C. 1251-
1
1387), as amended—Contracts and subgrants of amounts in excess of $150,000 must contain a provision that
requires the non-Federal award to agree to comply with all applicable standards, orders or regulations issued
pursuant to the Clean Air Act (42 U.S.C. 7401-7671q) and the Federal Water Pollution Control Act as amended (33
U.S.C. 1251- 1387). Violations must be reported to the Federal awarding agency and the Regional Office of the
Environmental Protection Agency (EPA).
When federal funds are expended by REGION 4 ESC for any contract resulting from this procurement process, the
vendor certifies that the vendor will be in compliance with mandatory standards and policies relating to energy
efficiency which are contained in the state energy conservation plan issued in compliance with the Energy Policy
and Conservation Act (Pub. L. 94-163, 89 Stat. 871).
When federal funds are expended by REGION 4 ESC for any contract resulting from this procurement process in
excess of $100,000, the vendor certifies that the vendor is in compliance with all applicable standards, orders,
regulations, and/or requirements issued pursuant to the Clean Air Act of 1970, as amended (42 U.S.C. 1857(h)),
Section 508 of the Clean Water Act, as amended (33 U.S.C. 1368), Executive Order 117389 and Environmental
Protection Agency Regulation, 40 CFR Part 15.
Pursuant to Federal Rule (G) above, when federal funds are expended by REGION 4 ESC, the vendor certifies that
during the term of an award for all contracts by REGION 4 ESC resulting from this procurement process, the vendor
agrees to comply with all applicable requirements as referenced in Federal Rule (G) above.
I certify compliance with this attribute.
1 FEDERAL RULE (H) - DEBARMENT AND SUSPENSION
1 (H) (Executive Orders 12549 and 12689)—A contract award (see 2 CFR 180.220) must not be made to parties
2
listed on the governmentwide exclusions in the System for Award Management (SAM), in accordance with the OMB
guidelines at 2 CFR 180 that implement Executive Orders 12549 (3 CFR part 1986 Comp., p. 189) and 12689 (3
CFR part 1989 Comp., p. 235), “Debarment and Suspension.” SAM Exclusions contains the names of parties
debarred, suspended, or otherwise excluded by agencies, as well as parties declared ineligible under statutory or
regulatory authority other than Executive Order 12549.
Pursuant to Federal Rule (H) above, when federal funds are expended by REGION 4 ESC, the vendor certifies that
during the term of an award for all contracts by REGION 4 ESC resulting from this procurement process, the vendor
certifies that neither it nor its principals is presently debarred, suspended, proposed for debarment, declared
ineligible, or voluntarily excluded from participation by any federal department or agency or by the State of Texas.
Vendor shall immediately provide written notice to REGION 4 ESC if at any time the vendor learns that this
certification was erroneous when submitted or has become erroneous by reason of changed circumstances.
REGION 4 ESC may rely upon a certification of a vendor that the vendor is not debarred, suspended, ineligible, or
voluntarily excluded from the covered contract, unless REGION 4 ESC knows the certification is erroneous.
I certify compliance with this attribute.
Page 29 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 FEDERAL RULE (I) - BYRD ANTI-LOBBYING AMENDMENT
1 (I) (31 U.S.C. 1352)—Contractors that apply or bid for an award exceeding $100,000 must file the required
3
certification. Each tier certifies to the tier above that it will not and has not used Federal appropriated funds to pay
any person or organization for influencing or attempting to influence an officer or employee of any agency, a
member of Congress, officer or employee of Congress, or an employee of a member of Congress in connection with
obtaining any Federal contract, grant or any other award covered by 31 U.S.C. 1352. Each tier must also disclose
any lobbying with non-Federal funds that takes place in connection with obtaining any Federal award. Such
disclosures are forwarded from tier to tier up to the non-Federal award.
Pursuant to Federal Rule (I) above, when federal funds are expended by REGION 4 ESC, the vendor certifies that
during the term and after the awarded term of an award for all contracts by REGION 4 ESC resulting from this
procurement process, the vendor certifies that it is in compliance with all applicable provisions of the Byrd Anti-
Lobbying Amendment (31 U.S.C. 1352). The undersigned further certifies that:
(1) No Federal appropriated funds have been paid or will be paid by or on behalf of the undersigned, to any person
for influencing or attempting to influence an officer or employee of any agency, a Member of Congress, an officer or
employee of Congress, or an employee of a Member of Congress in connection with the awarding of a Federal
contract, the making of a Federal grant, the making of a Federal loan, the entering into a cooperative agreement,
and the extension, continuation, renewal, amendment, or modification of a Federal contract, grant, loan, or
cooperative agreement.
(2) If any funds other than Federal appropriated funds have been paid or will be paid to any person for influencing
or attempting to influence an officer or employee of any agency, a Member of Congress, an officer or employee of
Congress, or an employee of a Member of Congress in connection with this Federal contract, grant, loan, or
cooperative agreement, the undersigned shall complete and submit Standard Form-LLL, “Disclosure Form to
Report Lobbying”, in accordance with its instructions.
(3) The undersigned shall require that the language of this certification be included in the award documents for all
subawards at all tiers (including subcontracts, subgrants, and contracts under grants, loans, and cooperative
agreements) and that all subrecipients shall certify and disclose accordingly.
This certification is a material representation of fact upon which reliance was placed when this transaction was
made or entered into. Submission of this certificate is a prerequisite for making or entering into this transaction
imposed by Section 1352, title 31, U.S. Code. Any person who fails to file the required certification shall be subject
to a civil penalty of not less than $10,000 and not more than $100,000 for each such failure.
I certify compliance with this attribute.
1 FEDERAL RULE (J) - PROCUREMENT OF RECOVERED MATERIALS
1 (J) When federal funds are expended by REGION 4 ESC, REGION 4 ESC and its contractors must comply with
4
section 6002 of the Solid Waste Disposal Act, as amended by the Resource Conservation and Recovery Act. The
requirements of Section 6002 include: (1) procuring only items designated in guidelines of the Environmental
Protection Agency (EPA) at 40 CFR part 247 that contain the highest percentage of recovered materials
practicable, consistent with maintaining a satisfactory level of competition, where the purchase price of the item
exceeds $10,000 or the value of the quantity acquired during the preceding fiscal year exceeded $10,000; (2)
procuring solid waste management services in a manner that maximizes energy and resource recovery; and (3)
establishing an affirmative procurement program for procurement of recovered materials identified in the EPA
guidelines.
Pursuant to Federal Rule (J) above, when federal funds are expended REGION 4 ESC, as required by the
Resource Conservation and Recovery Act of 1976 (42 U.S.C. § 6962(c)(3)(A)(i)), the vendor certifies, by signing
this document, that the percentage of recovered materials content for EPA-designated items to be delivered or used
in the performance of the contract will be at least the amount required by the applicable contract specifications or
other contractual requirements.
I certify compliance with this attribute.
Page 30 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 FEDERAL RULE (K) - PROHIBITION ON CERTAIN TELECOM AND SURVEILLANCE SERVICE AND
1 EQUIPMENT
5
(K) Region 4 ESC, as a non-federal entity, is prohibited from obligating or expending Federal financial assistance,
to include loan or grant funds, to: (1) procure or obtain,
(2) extend or renew a contract to procure or obtain, or
(3) enter into a contract (or extend or renew a contract) to procure or obtain, equipment, services, or systems that
uses covered telecommunications equipment or services as a substantial or essential component of any system, or
as a critical technology as part of any system. Covered telecommunications equipment is telecommunications
equipment produced Huawei Technologies Company or ZTE Corporation (or any subsidiary or affiliate of such
entities) and physical security surveillance of critical infrastructure and other national security purposes, and video
surveillance and telecommunications equipment produced by Hytera Communications Corporation, Hangzhou
Hikvision Digital Technology Company, or Dahua Technology Company (or any subsidiary or affiliate of such
entities) for the purpose of public safety, security of government facilities, physical security surveillance of critical
infrastructure, and other national security purposes detailed in 2 CFR § 200.216.
The Respondent certifies that it will not purchase equipment, services, or systems that use covered
telecommunications, as defined herein, as a substantial or essential component of any system, or as critical
technology as part of any system.
I certify compliance with this attribute.
1 FEDERAL RULE (L) - BUY AMERICAN PROVISIONS
1 (L) As appropriate and to the extent consistent with law, REGION 4 ESC has a preference for the purchase,
6
acquisition, or use of goods, products, or materials produced in the United States, including but not limited to iron,
aluminum, steel, cement, and other manufactured products, when spending federal funds. Vendor agrees that the
requirements of this section will be included in all subawards including all contracts and purchase orders for work or
products under this award, to the greatest extent practicable under a Federal award. Purchases that are made with
non-federal funds or grants are excluded from the Buy American Act.
Vendor certifies that it is in compliance with all applicable provisions of the Buy American Act. Purchases made in
accordance with the Buy American Act must still follow the applicable procurement rules calling for free and open
competition.
“Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stage through the application
of coatings, occurred in the United States. “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous
metals such as aluminum; plastics and polymer-based products such as polyvinyl chloride pipe; aggregates such as concrete; glass, including optical fiber;
and lumber.
I certify compliance with this attribute.
1 FEDERAL RULE - REQUIRED AFFIRMATIVE STEPES FOR SMALL, MINORITY, AND WOMEN-OWNED
1 FIRMS FOR CONTRACTS PAID FOR WITH FEDERAL FUNDS
7
When federal funds are expended by REGION 4 ESC, Vendor is required to take all affirmative steps set forth in 2
CFR 200.321 to solicit and reach out to small, minority and women owned firms for any subcontracting opportunities
on the project, including:
1) Placing qualified small and minority businesses and women's business enterprises on solicitation lists;
2) Assuring that small and minority businesses, and women's business enterprises are solicited whenever
they are potential sources;
3) Dividing total requirements, when economically feasible, into smaller tasks or quantities to permit maximum
participation by small and minority businesses, and women's business enterprises;
4) Establishing delivery schedules, where the requirement permits, which encourage participation by small
and minority businesses, and women's business enterprises; and
5) Using the services and assistance, as appropriate, of such organizations as the Small Business
Administration and the Minority Business Development Agency of the Department of Commerce.
I certify compliance with this attribute.
Page 31 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 FEDERAL RULE - FEDERAL RECORD RETENTION
1 When federal funds are expended by REGION 4 ESC for any contract resulting from this procurement process, the
8
vendor certifies that it will comply with the record retention requirements detailed in 2 CFR §200.334. The vendor
further certifies that vendor will retain all records as required by 2 CFR §200.334 for a period of five (5) years after
grantees or subgrantees submit final expenditure reports or quarterly or annual financial reports, as applicable, and
all other pending matters are closed.
Vendor agrees that REGION 4 ESC, Inspector General, Department of Homeland Security, FEMA, the Comptroller
General of the United States, or any of their duly authorized representatives shall have access to any books,
documents, papers and records of Vendor, and its successors, transferees, assignees, and subcontractors that are
directly pertinent to the Contract for the purpose of making audits, examinations, excerpts, and transcriptions. The
right also includes timely and reasonable access to Vendor’s personnel for the purpose of interview and discussion
relating to such documents. Vendor agrees to permit any of the foregoing parties to reproduce by any means
whatsoever or to copy excerpts and transcriptions as reasonably needed. Vendor agrees to provide the FEMA
Administrator or his authorized representative access to construction or other work sites pertaining to the work
being completed under the Contract.
I certify compliance with this attribute.
1 FEDERAL RULE - PROFIT NEGOTIATION
1 For purchases using Federal funds in excess of $250,000, REGION 4 ESC may be required to negotiate profit as a
9
separate element of the price. (See 2 CFR 200.324(b)).
When required by REGION 4 ESC, Vendor agrees to provide information relating to profitability of the given
transaction and itemize the profit margin as a separate element of the price.
I certify compliance with this attribute.
1 FEDERAL RULE - SOLID WASTE DISPOSAL ACT
2 A non-Federal entity that is a state agency or agency of a political subdivision of a state and its contractors must
0
comply with section 6002 of the Sold Waste Disposal Act, as amended by the Resource Conservation and Recovery
Act. The requirements of Section 6002 include procuring only items designated in guidelines of the Environmental
Protection Agency (EPA) at 40 CFR Part 247 that contain the highest percentage of recovered materials
practicable, consistent with maintaining a satisfactory level of competition, where the purchase price of the item
exceeds $10,000 or the value of the quantity acquired during the preceding fiscal year exceed $10,000; procuring
sold waste management services in a manner that maximizes energy and resource recovery; and establishing an
affirmative procurement program for procurement of recovered materials identified in the EPA guidelines. (78 FR
78608, Dec. 26, 2013, as amended at 79 FR 75885, Dec. 19, 2014.)
Pursuant to this federal rule, when federal funds are expended by REGION 4 ESC, the vendor certifies that during
the term of all contracts resulting from this procurement process, the vendor agrees to comply with all applicable
requirements as referenced in this paragraph.
I certify compliance with this attribute.
1 APPLICABLITY TO SUBCONTRACTORS
2 Vendor agrees that all contracts it awards pursuant to this procurement action shall be bound by the terms and
1
conditions of this procurement action.
I certify compliance with this attribute.
1 COMPLIANCE WITH THE ENERGY POLICY AND CONSERVATION ACT
2 When REGION 4 ESC expends federal funds for any contract resulting from this procurement process, Vendor
2
certifies that it will comply with the mandatory standards and policies relating to energy efficiency which are
contained in the state energy conservation plan issued in compliance with the Energy Policy and Conservation Act
(42 U.S.C. 6321 et seq.; 49 C.F.R. Part 18).
I certify compliance with this attribute.
Page 32 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 INDEMNIFICATION
2 Acts or Omissions
3
Vendor shall indemnify and hold harmless Region 4, AND/OR THEIR OFFICERS, AGENTS, EMPLOYEES,
REPRESENTATIVES, CONTRACTORS, ASSIGNEES, AND/OR DESIGNEES FROM ANY AND ALL LIABILITY,
ACTIONS, CLAIMS, DEMANDS, OR SUITS, AND ALL RELATED COSTS, ATTORNEY FEES, AND EXPENSES arising
out of, or resulting from any acts or omissions of the Vendor or its agents, employees, subcontractors, Order
Fulfillers, or suppliers of subcontractors in the execution or performance of the Contract and any Purchase Orders
issued under the Contract.
Infringements
a) Vendor shall indemnify and hold harmless Region 4 and Customers, AND/OR THEIR EMPLOYEES, AGENTS,
REPRESENTATIVES, CONTRACTORS, ASSIGNEES, AND/OR DESIGNEES from any and all third party claims
involving infringement of United States patents, copyrights, trade and service marks, and any other intellectual or
intangible property rights in connection with the PERFORMANCES OR ACTIONS OF VENDOR PURSUANT TO THIS
CONTRACT. VENDOR AND THE CUSTOMER AGREE TO FURNISH TIMELY WRITTEN NOTICE TO EACH OTHER
OF ANY SUCH CLAIM. VENDOR SHALL BE LIABLE TO PAY ALL COSTS OF DEFENSE INCLUDING ATTORNEYS’
FEES.
b) Vendor shall have no liability under this section if the alleged infringement is caused in whole or in part by: (i) use
of the product or service for a purpose or in a manner for which the product or service was not designed, (ii) any
modification made to the product without Vendor’s written approval, (iii) any modifications made to the product by
the Vendor pursuant to Customer’s specific instructions, (iv) any intellectual property right owned by or licensed to
Customer, or (v) any use of the product or service by Customer that is not in conformity with the terms of any
applicable license agreement.
c) If Vendor becomes aware of an actual or potential claim, or Customer provides Vendor with notice of an actual or
potential claim, Vendor may (or in the case of an injunction against Customer, shall), at Vendor’s sole option and
expense; (i) procure for the Customer the right to continue to use the affected portion of the product or service, or
(ii) modify or replace the affected portion of the product or service with functionally equivalent or superior product or
service so that Customer’s use is non-infringing.
Taxes/Workers’ Compensation/Unemployment Insurance – Including Indemnity
a) VENDOR AGREES AND ACKNOWLEDGES THAT DURING THE EXISTENCE OF THIS CONTRACT, VENDOR
SHALL BE ENTIRELY RESPONSIBLE FOR THE LIABILITY AND PAYMENT OF VENDOR’S AND VENDOR’S
EMPLOYEES’ TAXES OF WHATEVER KIND, ARISING OUT OF THE PERFORMANCES IN THIS CONTRACT.
VENDOR AGREES TO COMPLY WITH ALL STATE AND FEDERAL LAWS APPLICABLE TO ANY SUCH PERSONS,
INCLUDING LAWS REGARDING WAGES, TAXES, INSURANCE, AND WORKERS’ COMPENSATION. THE
CUSTOMER AND/OR REGION 4 SHALL NOT BE LIABLE TO THE VENDOR, ITS EMPLOYEES, AGENTS, OR
OTHERS FOR THE PAYMENT OF TAXES OR THE PROVISION OF UNEMPLOYMENT INSURANCE AND/OR
WORKERS’ COMPENSATION OR ANY BENEFIT AVAILABLE TO A STATE EMPLOYEE OR EMPLOYEE OF
ANOTHER GOVERNMENTAL ENTITY CUSTOMER.
b) VENDOR AGREES TO INDEMNIFY AND HOLD HARMLESS CUSTOMERS, REGION 4 AND/OR THEIR
EMPLOYEES, AGENTS, REPRESENTATIVES, CONTRACTORS, AND/OR ASSIGNEES FROM ANY AND ALL
LIABILITY, ACTIONS, CLAIMS, DEMANDS, OR SUITS, AND ALL RELATED COSTS, ATTORNEYS’ FEES, AND
EXPENSES, RELATING TO TAX LIABILITY, UNEMPLOYMENT INSURANCE AND/OR WORKERS’ COMPENSATION IN
ITS PERFORMANCE UNDER THIS CONTRACT, VENDOR SHALL BE LIABLE TO PAY ALL COSTS OF DEFENSE
INCLUDING ATTORNEYS’ FEES.
I certify compliance with this attribute.
1 EXCESS OBLIGATIONS PROHIBITED
2 Proposer understands that all obligations of Region 4 ESC under the contract are subject to the availability of state
4
funds. If such funds are not appropriated or become unavailable, the contract may be terminated by Region 4 ESC.
I certify compliance with this attribute.
1 SUSPENSION AND DEBARMENT
2 Respondent certifies that neither it nor its principals are debarred, suspended, proposed for debarment, declared
5
ineligible, or otherwise excluded from participation in the contract by any state or federal agency.
I certify compliance with this attribute.
Page 33 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
1 CHANGE IN LAW AND COMPLIANCE WITH LAWS
2 Proposer shall comply with all laws, regulations, requirements and guidelines applicable to a vendor providing
6
services and products required by the contract to the Region 4 ESC, as these laws, regulations, requirements and
guidelines currently exist and as amended throughout the term of the contract. Region 4 ESC reserves the right, in
its sole discretion, to unilaterally amend the contract prior to award and throughout the term of the contract to
incorporate any modifications necessary for compliance with all applicable state and federal laws, regulations,
requirements and guidelines.
I certify compliance with this attribute.
1 For the following categories, the Offeror shall provide the following information to include;
2 o HVAC Refrigeration
7
ꞏ Type (e.g., Rotary, Centrifugal, Scroll, Reciprocating., Absorption)
ꞏ Cooling medium (e.g., air, water)
ꞏ Brand Name(s)
ꞏ Capacity Range (tons)
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Range of Efficiencies (KW/Ton)
ꞏ Estimated Market Share (North America)
ꞏ Provide example data on each type of product provided
ꞏ Detail Features & Benefits
o Indoor Air Quality Products and Devices
ꞏ Type (Active polarization, non-ionizing, electronic air cleaning systems intended to replace passive filtration, any
other.)
ꞏ Brand Name(s)
ꞏ Capacity Range
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Range of Efficiencies
ꞏ Estimated Market Share (North America)
ꞏ Provide example data on each type of product provided
ꞏ Detail Features & Benefits
o Unitary
ꞏ Type (e.g., rooftops, split systems, VRFs, Heat Pumps, PTACs, water source, mini-splits)
ꞏ Brand Name(s)
ꞏ Capacity Range
ꞏ Heating Medium (Electric, Gas, Steam, Hot Water)
ꞏ Cooling Medium (DX, Chilled Water)
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Range of Efficiencies (EER, SEER, COP)
ꞏ Estimated Market Share (North America)
ꞏ Provide example data on each type of product provided
ꞏ Detail Features & Benefits
o Air handling
ꞏ Type (e.g. central station-manufactured or custom makeup air, fan,
ꞏ filter, coil sections)
ꞏ Brand Name(s)
ꞏ Fan Types (e.g. Backward incline, Forward curve, airfoil)
ꞏ Capacity Range (CFM)
ꞏ Heating Medium (Electric, Gas, Steam, Hot Water)
ꞏ Cooling Medium (DX, Chilled Water)
ꞏ Standard Warranty (Parts & Labor)
Page 34 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Estimated Market Share (North America)
ꞏ Provide example data on each type of product provided
ꞏ Detail Features & Benefits
o Air Terminal Devices and Heating Products
ꞏ Type (e.g. VAV, Fan Coils, Unit Ventilators, Unit Heaters, Fin Tube Radiation/Convectors)
ꞏ Brand Name(s)
ꞏ Capacity Range (CFM)
ꞏ Heating Medium (Electric, Gas, Steam, Hot Water)
ꞏ Cooling Medium (DX, Chilled Water)
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Estimated Market Share (North America)
ꞏ Provide example data on each type of product provided
ꞏ Detail Features & Benefits
o DDC Controls
ꞏ Type (core components, end devices, lighting, panels) Brand Name(s)
ꞏ System Protocol (BACnet, LonWorks, Proprietary or Combo)
ꞏ LAN Communication Structure (Peer-to-peer, Polling)
ꞏ Human Machine Interface (HMI) types (PC, Notebooks, Handheld terminals)
ꞏ Third party interface (Drivers and Gateways)
ꞏ Remote alarm and message capabilities
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Estimated Market Share (North America)
ꞏ Detail Features & Benefits
o Cooling Towers
ꞏ Type (e.g., open, closed, evaporative, other)
ꞏ Brand Name(s)
ꞏ Capacity Range (tons)
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Range of Efficiencies
ꞏ Estimated Market Share (North America)
ꞏ Provide example data on each type of product provided
ꞏ Detail Features & Benefits
o Pumps
ꞏ Type (e.g., single stage, split case, end suction, inline, circulator, turbines)
ꞏ Brand Name(s)
ꞏ Capacity Range (GPM)
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Range of Efficiencies
ꞏ Estimated Market Share (North America)
ꞏ Provide example data on each type of product provided
ꞏ Detail Features & Benefits
o Invertors
ꞏ Brand Name(s)
ꞏ Capacity Range (HP)
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
Page 35 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Estimated Market Share (North America)
ꞏ Provide example data on each type of product provided
ꞏ Detail Features & Benefits
o Boilers & Water Heaters
ꞏ Type (e.g., modulating, condensing, cast iron, water tube, packaged, other)
ꞏ Brand Name(s)
ꞏ Heating Medium (Electric, Gas, Steam, Hot Water)
ꞏ Capacity Range (MBH)
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Range of Efficiencies
ꞏ Estimated Market Share (North America)
ꞏ Provide example data on each type of product provided
ꞏ Detail Features & Benefits
o HVAC Specialty Products
ꞏ Type (e.g., modular, outside/inside, S&T Heat Recovery, Humidity
ꞏ Control, Heat Wheel, Heat Pipe, Heat Exchangers)
ꞏ Brand Name(s)
ꞏ Heating Medium (Electric, Gas, Steam, Hot Water)
ꞏ Cooling Medium (DX, Chilled Water)
ꞏ Capacity Range (CFM and/or MBH)
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Location of Manufacturing (City, State or Country)
ꞏ Range of Efficiencies
ꞏ Estimated Market Share (North America)
ꞏ Provide example data on each type of product provided
ꞏ Detail Features & Benefits
ꞏ Refrigeration Products
ꞏ Display Cases
ꞏ Refrigeration Systems
ꞏ Glass Doors & Lids
ꞏ Walk-in Products
ꞏ Others
o LED Lighting Products
ꞏ LED Area Lights
ꞏ Flexible LED Strips
ꞏ Ceiling Lighting
ꞏ Bulbs, Fixture Products
ꞏ Others
o Equipment Parts and Supplies
ꞏ Type (e.g., manufactured parts, emergency parts service, miscellaneous material and supplies and other)
ꞏ Brand Name(s) stocked
ꞏ Location of stocking parts
ꞏ Standard Warranty (Parts & Labor)
ꞏ Optional Warranty (components covered & Labor)
ꞏ Estimated Lead/Delivery Time
ꞏ Percentage of locally stocked parts to delivered parts
Detail Features & Benefits
1 Offerors are requested to provide service forms with detailed description of your service offerings.
2 Provide service forms with detailed descriptions; at a minimum, Offerors are to include the following
8 information as it is applicable to their product,
service, and solutions offering:
o Startup & Commissioning Services
Page 36 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
ꞏ Define process for validation of system or equipment operation to design
ꞏ Type (e.g., equipment startups, system checkouts, control verification, retro commissioning, M & V verifications,
rebate auditing, other)
ꞏ List key personnel (factory, sub-contract, other)
ꞏ References (public sector only)
ꞏ Case studies describing benefits of services
o Service & Maintenance
ꞏ Type (e.g., preventative and full maintenance contracts, man-at attendance, remote monitoring, annuals,
emergency services, regulatory compliance, cleaning (e.g., duct, coils and filters), scheduled maintenance (e.g., oil,
chemical and vibration analysis) and other)
ꞏ Define processes for each type of service and/or maintenance of the system or the equipment
ꞏ List key personnel (factory, sub-contract, other)
ꞏ References (public sector only)
ꞏ Case studies describing benefits of services
o Installation and Turnkey Contracting
ꞏ Type (e.g., retrofit, new construction, energy retrofit, controls new- and upgrade and other)
ꞏ Define processes for each type install of the system or the equipment
ꞏ Bonding and licensing capabilities
ꞏ List key personnel (factory, sub-contract, other)
ꞏ References (public sector only)
ꞏ Case studies describing benefits of services
o Warranty Services
ꞏ Type (e.g., Extended parts & labor (define maximum number of years available), delayed start-up and other)
ꞏ Define processes for each type of warranty
ꞏ List key personnel (factory, sub-contract, other)
ꞏ References (public sector only)
ꞏ Case studies describing benefits of services
o Energy Services
ꞏ Type (e.g., (Energy Tracking, Energy Analysis, Evaluation of potential upgrades, demand response, rebates and
others)
ꞏ Define processes for each type of energy services
ꞏ Certifications of personnel
ꞏ List key personnel (factory, sub-contract, other)
ꞏ References (public sector only)
ꞏ Case studies describing benefits of services
o Equipment Rentals
ꞏ Type (e.g., chillers, pumps, transformers, terminal units, generators, cooling towers, packaged unitary and other)
ꞏ Brands available
ꞏ Locations of rental fleet
ꞏ Process of accessing rental fleet during disaster event
ꞏ List key personnel (factory, sub-contract, other)
ꞏ References (public sector only)
ꞏ Case studies describing benefits of services
o Financial Services
ꞏ Type (e.g., leasing, prompt and pre-payment discounts, guaranteed
ꞏ savings and other)
ꞏ Describe type of each funding and availability
ꞏ Funding Sources (internal and/or external)
ꞏ List key personnel (internal and/or external)
ꞏ References (public sector only)
ꞏ Case studies describing benefits of services
o Professional Services
ꞏ Describe type of each professional service and availability
ꞏ Licensing and certification capabilities
ꞏ List key personnel (internal and/or external)
ꞏ References (public sector only)
ꞏ Case studies describing benefits of services
o Site Surveys
ꞏ Type (e.g., Equipment, system analysis, operational, architectural and other)
ꞏ Describe type of survey
ꞏ Licensing and certification capabilities
Page 37 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
ꞏ Advanced technology uses for each type of survey
ꞏ List key personnel (internal and/or external)
ꞏ References (public sector only)
ꞏ Case studies describing benefits of services
Page 38 of 38 pages Vendor: Daikin Applied Americas, Inc 24-09 Addendum 3
DAIKIN APPLIED AMERICAS INC
Products and Pricing A achment
Page 2 – Daikin Applied Labor Rates
Page 7 – Daikin Applied HVAC Equipment Categories Product Discounts
Page 15 – Daikin Applied Product Line Card
Page 21 – Daikin Applied Rental Solu#ons
Page 28 – Daikin Applied Solu#ons Offering
Page 70 – Daikin Applied Protec#ve Maintenance Plans
Page 73 – Daikin Applied Service Solu#ons Programs
Page 74 – Daikin Applied Energy Analyser Building Assessments
Page 78 – Daikin Applied Service Programs
Page 106 – Daikin Applied Con#ngency Planning
Page 108 – Daikin Applied Con#ngency Planning for Schools
Page 110 – Daikin Applied Safety Report
Page 111 – Daikin Applied Divisional Sales Territories
Page 112 – Daikin Applied Equipment Representa#ves
Page 244 – Daikin Applied Service Respresenta#ves
Page 277 – Daikin Applied Limited Product Warranty
Page 278 – Daikin Applied Case Study Ohio Based Public University
Page 280 – Daikin Applied Case Study New Jersey Public School District
Page 282 – Daikin Applied Case Study Overby Sheppard Elementary School
Product
Line Card
Daikin Applied
HVAC System Solutions
Advanced technology and solutions from
the world’s leading HVAC innovator.
Innovative HVAC technology
CHILLER SYSTEMS
| WATER COOLED | AIR COOLED
Magnitude® Magnetic Bearing Centrifugal Chiller, Pathfinder® Trailblazer®
Centrifugal Chiller Single Compressor Screw Chiller w/Free Cooling Scroll Chiller
86 to 1,600 tons 300 to 1,350 tons 100 to 565 tons 10 to 240 tons
| CONDENSING UNITS
Centrifugal Chiller, Dual Centrifugal Chiller, Dual Single Circuit Dual Circuit
Compressor – Single Circuit Compressor – Dual Circuit Scroll Condenser Scroll Condenser
600 to 2,500 tons 1,200 to 2,700 tons 6 to 20 tons 15 to 140 tons
RENTAL CHILLERS
Navigator™ Screw Chiller Scroll Chiller
120 to 300 tons 30 to 200 tons
Air Cooled
Pathfinder® & Trailblazer®
TEMPLIFIER® WATER HEATERS PACKAGED ENGINEERED SYSTEMS
Scroll Centrifugal Modular Central Plant Packaged Mechanical System
500 to 3,100 MBh 3,000 to 18,000 MBh Up to 10,000 tons Cooling & Up to 10,000 tons Cooling &
100,000 MBh Heating 100,000 MBh Heating
AIR HANDLERS – CUSTOM, SEMI-CUSTOM AND COMMERCIAL
| COMMERCIAL | CUSTOM
ECM PreciseLine™ Lg. Capacity Rebel® Commercial
Fan Array Indoor Air Handler Outdoor Air Handler Custom Air Handler
600 to 5,000 cfm 600 to 5,000 cfm 500 to 11,500 cfm 900 − 129,000 cfm
| SEMI-CUSTOM SITELINE™ BUILDING CONTROLS
Vision® Semi-Custom Skyline® Semi-Custom RoofPak® Semi-Custom SiteLine™ for SiteLine™ for
Indoor Air Handler Outdoor Air Handler Rooftop Air Handler Dedicated Equipment Pre-programmed BAS
900 to 100,000 cfm 900 to 65,000 cfm 4,000 to 50,000 cfm SiteLine™ for
Wireless BAS
PACKAGED ROOFTOP SYSTEMS
| LT. COMMERCIAL | COMMERCIAL | APPLIED
Maverick® I Rebel® Cooling and Heat Maverick® II Rebel Applied™ Heating & RoofPak® Heating & Cooling
Cooling & Heat Pump Pump w/Inv. Compressor Heating & Cooling Cooling w/Inv. Compressor w/Inv. Compressor
3 to 25 tons 3 to 28 tons 26 to 75 tons 20 to 52 tons 45 to 150 tons
PACKAGED VERTICAL SELF-CONTAINED SYSTEMS
Indoor Cooling & Heating Water-cooled Condenser − Unitary Indoor Cooling & Heating Water-cooled Condenser − Retrofit
20 to 130 tons 20 to 40 tons
Solutions for new & existing installations
WATER SOURCE HEAT PUMPS
SmartSource® Dedicated SmartSource® High SmartSource® Compact Enfinity® Enfinity®
Outside Air System Efficiency Horiz. / Vert. Horizontal / Vertical Console In-Room Horizontal / Vertical
600 to 4000 cfm ½ to 6 tons ½ to 6 tons ½ to 1½ tons ½ to 6 tons / ¾ to 6 tons
VAV BOXES AIR PURIFIER
Large Capacity Vertical Single Duct & Air
Horizontal / Vertical Stacked Series / Parallel PIUs Purifier
6 to 25 tons ¾ to 3 tons 80 to 8000 cfm 500 & 1000 cfm
FAN COILS/BLOWER COILS UNIT VENTILATORS
Horizontal ThinLine Horizontal, Vertical, & Ceiling & Self-Contained, Heat Pump
Economy Vertical & Horizontal Cabinet Unit Heaters Floor Units & WSHP Floor Units
200 to 1,200 cfm 200 to 1,200 cfm 200 to 12,350 cfm 750 to 2,000 cfm 24 to 54 MBh
COILS
Large PreciseLine™ OptiLine™
Capacity Small Capacity Blower Coil Vertical Stacked Chilled Water, Hot Water, Steam, & DX Coils
600 to 3,000 cfm 600 to 5,000 cfm 300 to 1,200 cfm 1 to 12 rows
We believe your air can be doing more.
Daikin Industries, Ltd. is a Forbes 1000 global
company with 2022 revenues of over $27billion and
more than 88,000 employees worldwide, making
it the largest HVAC manufacturer in the world.
Daikin Applied designs and manufactures advanced
commercial and industrial HVAC systems for
customers around the world. Our technology and
services play a vital role in creating comfortable,
efficient and sustainable spaces to work and live
— and in delivering quality air to workers, tenants
and building owners. Daikin Applied solutions are
sold through a global network of dedicated sales,
service and parts offices.
THE INDUSTRY LEADER IN ENVIRONMENTAL SOLUTIONS
We are strongly committed to protecting the health and safety of people while
finding sustainable solutions to lead the industry. As an HVAC leader, we recognize
the unique opportunity to make a difference in environmental initiatives while
educating the next generation to further improve efficiencies and create a
more sustainable world for all. Climate change is a pressing issue today and we
challenge ourselves to solve it. Our investments in innovation, technology, and
sustainability earned Frost & Sullivan’s Manufacturing Leadership Award. Our
products save energy, reduce environmental impact, and help facilities earn points
toward LEED® certification with EPD verification.
Comprehensive HVAC solutions customized to
the needs of your business.
COMMERCIAL HVAC SERVICES
Daikin Applied offers comprehensive building solutions including service and parts for all HVAC components, systems
and brands. Our veteran building advisors and factory-trained technicians partner with our clients offering a suite of
services that allow for customized solutions to specifically meet your needs. We offer start-up services, maintenance
agreements, 24-hour emergency repair, HVAC replacement and upgrades, chiller rentals, building and energy analysis,
asset management, and more.
PARTS
Our complete line of quality parts and supplies keep your
systems operating reliably at peak efficiency with a centrally-
located, award-winning national parts warehouse that gets
the right parts to you, fast.
RENTAL SOLUTIONS
Daikin Applied rental equipment and temporary heating or
cooling capabilities are at your service 24/7 throughout the
United States and Canada. We offer complete support that
includes everything you need – from rental chillers and
dehumidifiers to heat and power.
For more information about our complete line of product offerings, contact your local Daikin Applied sales office
or visit DaikinApplied.com to find an office near you.
ASP 31-312 (4/23) ©2023 Daikin Applied | (800) 432-1342 | www.DaikinApplied.com
DAIKIN RENTAL
SOLUTIONS
Keeping You Up and Running
WEATHER THE UNEXPECTED
RELIABLE RENTAL SOLUTIONS WHEN YOU NEED THEM MOST.
CHILLERS & COOLING AIR CONDITIONERS
HEATING & BOILERS POWER DEHUMIDIFIERS
LEARN MORE AT DAIKINAPPLIED.COM
© 2023 DAIKIN APPLIED
TEMPORARY HVAC SOLUTIONS
CUSTOMIZED TO MEET THE NEEDS
OF YOUR BUSINESS.
WEATHER THE UNEXPECTED
Whether you have long or short-term cooling needs, Daikin delivers reliable rental solutions, applications expertise, and
responsive support. As a building owner, facilities engineer or manager, you are always planning for “what ifs.” Not to mention
grappling with actual building emergencies. Daikin Applied rental equipment and temporary heating/cooling capabilities are
at your service 24/7 throughout the United States and Canada. We offer complete support that includes everything you need
– from chillers and dehumidifiers to heat and power.
EMERGENCY RENTALS
When your equipment fails, limiting downtime is mission critical.
Daikin Applied provides quick delivery and installation of reliable
rental products to help you weather the outage. We’re here to help
get you back up and running, and can provide a turnkey solution.
> Industry-leading efficiency and proven technology
> 24-hour turnaround on available inventory
> 8-hour average set up with on-site experts
> Comprehensive package, including pumps, flexible water
piping connections, and electrical hookups
EQUIPMENT FOR PLANNED SITUATIONS
Forming a contingency plan in the event of an outage can
help you quickly get operations back to normal, limit financial
loss, and help you breathe easier when the unexpected
happens. Selecting the right-sized equipment is just one
part of the process. The best contingency plans start by
assessing and understanding your financial risk, and then
using this information to drive the rest of your plan. Our
Rental Solutions experts can specify the supplemental cooling
system required to support any situation you’re experiencing.
> System maintenance
> Building expansion
RENTALSOLUTIONS@DAIKINAPPLIED.COM
> Server room heat generation
> Seasonal/staff heat load swings
> Contingency plans
© 2023 DAIKIN APPLIED | (800) 553-0445 | WWW.DAIKINAPPLIED.COM | ASP 31-545
CHILLERS AND COOLING TOWERS
FOR DOWNTIME OR SUPPLEMENTAL
CAPACITY.
TEMPORARY CHILLER AND COOLING TOWER RENTALS
When faced with equipment failure or an unexpected outage during the cooling season, it’s important to know where to turn
to during a building emergency. That’s why Daikin Applied Rental Solutions offers a range of air-cooled and water-cooled chiller
units, applications expertise, and responsive support to meet your long or short-term cooling needs. For planned situations to
mission-critical emergencies, we’re here to help you weather the unexpected.
Air-cooled Water-cooled Cooling Towers
> 20 to 527 tons > Up to 1,000 tons > Up to 1,000 tons
> Skid mounted (Up to 267 tons) and Trailer mounted (300+ tons) > Containerized > Open & closed loop tower
> Integral pumps > Single-point power connection > Skid & trailer mounted
> Single-point power connection > Stainless steel basins
FOR MISSION CRITICAL OPERATIONS
When your equipment fails, downtime can be costly to your
business, especially for mission critical operations. Whether you’re
looking to mitigate the heat generated by your server room, or
secure patient health in your healthcare facility, we’ve got you
covered. Our factory-trained rentals solutions teams provide quick
delivery and installation to help get you back up and running.
REMOTE MONITORING FEATURES
Secure the ultimate peace of mind with remote access to your
rental chiller. Daikin offers a range of rental chiller models
available with remote monitoring capabilities, perfect for times
when presence on site is inconvenient or impractical.
© 2023 DAIKIN APPLIED | (800) 553-0445 | WWW.DAIKINAPPLIED.COM | ASP 31-545
AIR CONDITIONERS AND SPOT
COOLERS FOR TEMPORARY COOLING
APPLICATIONS.
RENTAL AIR CONDITIONING SOLUTIONS
Whether you require a significant amount of cooling to circulate around a larger space or need cooler temperatures in a
specified hot spot, Daikin offers a range of range of air- and water-cooled air conditioners, spot coolers and accessories that
are easy to use and simple to maintain. Available for a variety of applications that require efficient cooling in a portable capacity,
our portable cooling solutions are easily accessible with a fast, easy start-up and installation.
Air-cooled Water-cooled Spot coolers
> 5 to 100 tons > 1 to 5 tons > 1 to 7 tons
> Up to 240,000 Btu > Up to 60,000 Btu > Up to 92,000 Btu
> Skid & trailer mounted > Portable Units > Automatic restart function
UNIT TESTING APPLICATIONS
Selecting a permanent cooling solution for your facility can be a
complex process. Finding a unit that meets your unique project
requirements is key to your project’s success. Daikin Rental
Solutions provides a range of temporary cooling tower rentals for
cooling system testing applications – helping avoid costly long-
term errors, ensuring efficient and reliable operation before a
permanent solution is available.
ACCOMMODATE SEASONAL LOAD SWINGS
When outside ambient temperatures or staff changes result in
high temperatures that exceed your expected load demands,
Daikin Rental Solutions offers supplemental air conditioners,
spot coolers, and outdoor portable cooling units. By eliminating
purchasing additional equipment that might be only used part
of the year, you save on capital expenditures.
© 2023 DAIKIN APPLIED | (800) 553-0445 | WWW.DAIKINAPPLIED.COM | ASP 31-545
SECURE HEALTHIER INDOOR AIR
WITH RENTAL DEHUMIDIFICATION
AND VENTILATION SOLUTIONS.
RENTAL VENTILATION AND DEHUMIDIFIERS
A sudden change in your facility’s indoor air environment can pose more than just a risk to your occupant’s health and
comfort. It can also adversely effect product quality, posing financial risk to your business outcomes. Secure a healthy Indoor
Environmental Quality (IEQ) with Daikin Rental Solutions. We offer a range of rental dehumidifiers and air scrubbers, designed
to accommodate a diverse range of applications, from manufacturing environments to healthcare facilities.
Dessicant Circulation Fans LGR Air Movers Air Scrubbers Air Handlers
> 20 to 527 tons > 1,000 to 13,000 cfm > Automatic > 1,350 cfm > 500 to 2,000 cfm > 5,500 to 20,000 cfm
> Safety certified humidistat control > 3 operating speeds
> Skid mounted (Up to > Up to 3 machines in > Compact & industrial
267 tons) and trailer > Space saving > Up to 400 cfm > Portable a circuit sized options
mounted (300+ tons) > Self-monitoring > HEPA filtration
> Integral pumps
> Single-point power
connection
IEQ FOR MANUFACTURING FACILITIES
In today’s manufacturing environment, quality control is essential to
your product quality. So when your manufacturing space is met with
an unexpected rise in humidity levels, it can leave your products
and machinery vulnerable to potential mold, corrosion, or steam
exposure. Partner with Daikin Rental Solutions for an industrial
dehumidifier rental designed to maintain low humidity levels and
achieve a steady indoor micro-climate.
MITIGATE WATER DAMAGES
Harsh weather conditions and unexpected flooding can often lead
to water damages to your inventory and property such as wood
rot, mold and bacteria growth, metal rust and corrosion, and
possible damage to laminated materials and surfaces. Daikin offers
rental desiccant and Low Grain Refrigeration (LGR) dehumidifiers
designed to accommodate water damage restoration and for
applications that require the driest conditions possible.
© 2023 DAIKIN APPLIED | (800) 553-0445 | WWW.DAIKINAPPLIED.COM | ASP 31-545
HEATING EQUIPMENT FOR
SUPPLEMENTAL AND IAQ
APPLICATIONS.
RENTAL HEATING AND BOILER SOLUTIONS
When faced with equipment failure or an unexpected outage during the heating season, it’s important to know where to turn
to during a building emergency. Daikin offers reliable supplemental heating solutions, applications expertise, and responsive
support to help maintain a comfortable and healthy indoor air environment. From indirect and direct heaters, to concealed
flame and portable commercial heaters, our temporary heating capabilities are at your service 24/7.
Direct Fired Concealed Flame Indirect Fired Portable Electric Steam/Hot Water
> 500,000 to 3 million > 45,000 to 4.5 million > 100% clean air > 9kW to 150kW > Use existing steam
Btu Btu > 500,000 to 2 million Btu or hot water loop
> Ideal when natural
> Thermostat control > Clean air for IAQ and gas & propane is > Help minimize
> Backward inclined blowers for large cfm output unavailable
> Up to 7,700 cfm occupied spaces & static pressure project fuel cost
> Supplemental reheat > IAQ ready for
for existing building occupied spaces
systems > Effective for small
spaces
ELECTRIC HEATING SOLUTIONS
Optimal for smaller, temperature-sensitive environments, Daikin offers
temporary electric heating equipment as a flexible, portable, and effective
supplemental heating solution. Commercial portable heating solutions
are ideal for temperature-sensitive environments, such as a laboratory
or electronics room, and serve as an effective, IAQ-ready solution to
maintain consistent temperatures and humidity levels.
HEATING FOR TIGHT BUDGET PROJECTS
When project budget margins are tight, Daikin offers a range of
steam and hot water heaters that are lightweight and easy to
install. This equipment serves as an effective, temporary solution
to help minimize project fuel costs by using an existing steam or
hot water loop to help heat your project and supply clean dry air.
© 2023 DAIKIN APPLIED | (800) 553-0445 | WWW.DAIKINAPPLIED.COM | ASP 31-545
RESTORE AND MAINTAIN POWER
WITH PORTABLE POWER SOLUTIONS
AND ACCESSORIES.
RENTAL POWER SOLUTIONS AND ACCESSORIES
A loss of facility power can be more than just a minor inconvenience. For many facilities, can put occupant safety at risk
and can put an entire halt to business operations. Daikin’s rental power solutions and accessories are designed to help
you avoid costly electrical grid brownouts and blackouts. We offer a full line of professionally maintained, leading-edge
power equipment and accessories to help you restore power where and when you need it most.
Portable Generators Transformers Load Banks Power Distribution Fuel Tanks Accessories
> 20kW to 1mW > NEMA 3R > 1,000kW to 5,000kW > Spider boxes > 500 to 2,000 gallons > Cables
> Diesel fuel weatherproof > Portable > Transfer switches > Stationary and
> Trailer mounted > 15kW to 400kW > Weatherproof transportable
> 200 to 1,200 amp
> Step up/down I-Line Panels > Double-walled
capable
VALIDATE ELECTRICAL SYSTEM INTEGRITY
When you’re faced with an equipment failure, downtime can leave a
costly impact on your business, especially when it comes to mission
critical operations. Daikin offers a range of portable and fixed-place
load bank rentals for large utility testing applications. Our rental
units are easy-to-use and serve as effective solution when verifying
electrical system integrity in data centers, health care facilities,
backup generator systems and more.
GENERATOR UNITS FOR ANY APPLICATION
Whether your facing an emergency outage, supplemental power requirements, or planned maintenance, finding a temporary
power solution that fits your exact application demands can be difficult. Daikin provides a wide range of portable generator
rentals to accommodate even the most demanding job sites. With models ranging up to 1 megawatt capacity and units durable
enough to withstand extreme conditions, we provide power solutions to meet your specific needs and budget.
FOR MORE INFORMATION ABOUT OUR COMPLETE LINE OF RENTAL
PRODUCTS, EMAIL RENTALSOLUTIONS@DAIKINAPPLIED.COM
OR VISIT DAIKINAPPLIED.COM TO FIND AN OFFICE NEAR YOU.
SOLUTIONS
OFFERING
Daikin Applied HVAC Systems
LEARN MORE AT DAIKINAPPLIED.COM
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM
THE WORLD’S
LEADING INNOVATOR IN HVAC
LEADING THE WAY FOR OVER 95 YEARS
WHO WE ARE
Daikin Industries, Ltd. is a Forbes 1000 global company with
revenues of $27 billion and more than 88,000 employees
worldwide, making it the world’s number one air-conditioning
company. Daikin is engaged primarily in the development,
manufacture, sales and aftermarket support of heating,
ventilation, air conditioning and refrigeration (HVACR)
equipment, refrigerants and other chemicals, as well as oil
hydraulic products.
THE INDUSTRY LEADER
IN ENVIRONMENTAL SOLUTIONS
We are strongly committed to protecting the health and safety of
people while finding sustainable solutions to lead the industry. As an
HVAC leader, we recognize the unique opportunity to make a difference
in environmental initiatives while educating the next generation to
further improve efficiencies and create a more sustainable world for
all. Our investments in innovation, technology, and sustainability earned
Frost & Sullivan’s Manufacturing Leadership Award. Our products
save energy, reduce environmental impact, and help facilities earn
points toward LEED® certification with Environmental Product
Declaration (EPD®) verification.
As our HVAC technologies advance global standards for
sustainability, It is equally important to ensure our processes
do too. Our organization is home to a total of eight ISO 14001
certified sites, demonstrating the use of strong and
verifiable environmental management systems (EMS) and
further supporting our already strong commitment to
environmental stewardship.
2 © 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM
PRODUCT INDEX
DAIKINAPPLIED.COM
Self Contained . . . . . . . . . . . . . . . . . . . . . . . . . 8
Daikin Applied’s official website serves
Rooftops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 as a library of resources, including our
product information, catalogs, manuals,
Coils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 brochures and more.
Condensing Units . . . . . . . . . . . . . . . . . . . . . . 16
Air Handlers . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Water-cooled Chillers . . . . . . . . . . . . . . . . . . 22
Air-cooled Chillers . . . . . . . . . . . . . . . . . . . . . 26
Modular Central Plants . . . . . . . . . . . . . . . . . 28
SiteLine Building Controls . . . . . . . . . . . . . . 29
Unit Heaters/Fan Coils . . . . . . . . . . . . . . . . . 30 Product IM/OM Brochures
Catalogs Manuals
Air Purifier . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Water Source Heat Pumps . . . . . . . . . . . . . . 34
Case Controls Revit
Variable Air Volume . . . . . . . . . . . . . . . . . . . . 39 Studies Integration Files
Unit Ventilators . . . . . . . . . . . . . . . . . . . . . . . 40
Photo Video Design
Library Library Software Tools
Archived Application
Resources Software
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 3
OUR SERVICES & OFFERINGS
DAIKIN SERVICE SOLUTIONS:
WE MAKE BUILDINGS BETTER
Make no mistake about it, your building can be your second-best
employee. It’s an essential investment to grow your company for
the future, so it’s critical to help it perform to your employees’
and your customers’ standards. Daikin Service can help you
build convenience by keeping current systems up and running;
build confidence by implementing upgrades to existing systems;
and build excellence to make your system and facilities best-in-
class. daikinapplied.com/services
DELIVERING BUILDING CONVENIENCE,
CONFIDENCE AND EXCELLENCE
Maximize the Life Upgrade and Achieve Best-in-Class
of Your System Modernize Facilities
REPLACEMENT PARTS:
YOU DON’T HAVE TIME FOR DOWNTIME
When you need OEM or generic parts to repair your HVAC
system, you need them quickly. Daikin Service has an expansive
inventory and a centralized distribution center in Dayton, Ohio,
to get the right parts to you faster than ever before. To mitigate
downtime, we have 80 locations (and counting) across North
America. daikinapplied.com/parts
4
RENTAL SERVICES:
WEATHER THE UNEXPECTED
Planning for “what ifs” can be a real game changer
for building owners, facility engineers and facility
managers, not to mention grappling with actual heating
and cooling emergencies. Contingency planning can
solve both long- and short-term needs.
Daikin Service delivers chillers, dehumidifiers, heat and
power solutions, as well as applications expertise and
responsive support. Our rental chillers and temporary
cooling capabilities are at your service 24/7 throughout
the United States and Canada.
We offer a complete package with your rental chiller, including pumps, flexible water piping connections,
and electrical hookups. daikinapplied.com/rentals
SOLUTIONS PLAZA:
EXPERIENCE INTERACTIVE INNOVATION
Occupying the 21st floor of the Exchange Place Centre in New Jersey,
our Solutions Plaza allows visitors to explore Daikin’s new technologies
firsthand with our high-tech showroom containing our newest HVAC
products. Solutions Plaza gives engineers, owners, contractors, architects
and customers the knowledge they need to have confidence in their
buying decisions. With customized customer visits, remote witness
tests, continuing education seminars, industry meetings and much more,
© 2022 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM
Solutions Plaza is the perfect way to make an impact.
daikinapplied.com/industry-solutions/solutions-plaza
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 5
INDUSTRY-LEADING INNOVATION WITH DAIKIN TECHNOLOGY
APPLIED DEVELOPMENT CENTER:
TESTING FACILITY FOR GLOBAL APPLIED R&D
The Daikin Applied Development Center is the world’s most advanced
facility for HVAC research and development. The location serves as a
center of innovation to develop and test advanced chiller, compressor
and other HVAC technologies that will reduce energy consumption and
ultimately lower the carbon footprint of buildings.
© 2022 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM
DAIKIN LEARNING:
LEARN FROM THE INDUSTRY PROFESSIONALS
Daikin Learning drives business value by providing excellence in
learning to our external and internal customers. Daikin Learning is
transforming learning into modern, technology-enabled and scalable
experiences driving business value and creating excellence in HVAC
training.
Our goal is to provide the product-specific education necessary to
establish a high level of proficiency in operating and servicing Daikin
products. daikinapplied.com/training
CREATING EXCELLENCE IN HVAC TRAINING
6
DAIKIN APPLIED NATIONAL ACCOUNTS:
As a Daikin Applied National Account, you get the services of an HVAC
expert who understands your systems, business and priorities. Your Daikin
Applied representative will make your life easier by finding the perfect
solutions to your HVAC challenges, saving you both time and money. You
will also have the support of an extended team — a team you can leverage
to gain insights, quickly resolve issues and maximize performance-from a
single building to an entire enterprise.
We provide specialized expertise in market segments such as healthcare,
K-12 and higher education, retail/grocery, data centers, logistics,
manufacturing, hospitality, office, and local, state and federal government.
COOPERATIVE PURCHASING:
POWER IN PARTNERSHIP
Cooperative purchasing networks ensure full compliance to
their respective sector by ensuring jobs are competitively
bid on a regular basis. Vendors must meet all national
mandates and provide competitive quotes. Purchasing
organizations enjoy increased purchasing power and a
simpler buying process. Participants have access to Daikin
Applied’s full scope of advanced technology solutions,
including commercial HVAC systems, comprehensive HVAC
services and turnkey solutions.
DAIKIN APPLIED BUILDING SERVICES
As a Daikin Applied National Account, you have
priority access to our Building Services portfolio
of offerings, which includes:
Preventive Maintenance Agreements and Plans
Building Optimization
Energy Savings Evaluations
Equipment Replacement Analysis
Indoor Air Quality (IAQ) Analysis
On-Site Training
Systems Evaluation
Rental Solutions
Turnkey Equipment Replacement
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 7
SELF-CONTAINED
ADVANCED TECHNOLOGIES. UNPARALLELED PERFORMANCE
Self-contained systems provide a unique solution to meet project demands. These units can be
built and shipped as a complete system, or alternatively, they can be built and shipped in
module sections to easily fit into freight elevators and through narrow hallways/doors.
APPLICATIONS
HEALTHCARE
OFFICE BUILDINGS
SCHOOLS
MANUFACTURING
HOSPITALITY
NAME/MODEL:
SELF-CONTAINED 20-40 ton
SWT
Demanding Retrofit
SELF-CONTAINED 20-130 ton
SWP
New Construction/Retrofit
Tons 0 25 50 75 100 125 150
8
MODEL SWT
PERFORMANCE
DEMANDING RETROFIT 240-576 Mbh
SELF-CONTAINED 20-40 tons
018-040 sizes
4,500-16,000 cfm
The modular self-contained SWT
system offering is easily disassembled R-407C
and assembled into three compact
FEATURES
sections; (1) main cooling and heating,
(2) filter and waterside economizer,
Modular, 34-inch
and (3) plenum fan assembly to meet maximum sections
application and performance needs
MERV 8, 11, 13 or 14
for demanding retrofit appications. filtration
Variable and constant
air volume configurations
Free cooling economizer
MODEL SWP
PERFORMANCE
240-1701 Mbh NEW CONSTRUCTION/RETROFIT
20-130 tons
023-130 sizes
SELF-CONTAINED
For new construction or easy retrofit projects, self-contained
3,440-42,780 cfm SWP systems offer design flexibility, durable construction,
R-410A quiet operation, low installation costs and improved operating
efficiencies. These
FEATURES systems are ideal for
applications where
Quiet SWSI airfoil energy efficiency,
plenum fan
reliability, better
Factory-installed indoor air quality
variable frequency drives
and acoustics are
Controls flexibility for top priorities.
easy BAS integration
MERV 8, 11, 13 or
14 filtration
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 9
ROOFTOPS
ADVANCED TECHNOLOGIES. UNPARALLELED PERFORMANCE
Daikin Applied rooftop systems offer flexible ways to provide treated air for one to eight-story
buildings. Our 3-25 ton light commmercial, 3-75 ton commercial and 45-140 ton applied rooftop systems
offer scaleable solutions for engineers, contractors and building owners across North America.
NAME/MODEL:
APPLICATIONS
MAVERICK® I
MPS 3-25 ton HEALTHCARE
Light Commercial
OFFICE BUILDINGS
SCHOOLS
REBEL® MANUFACTURING
DPS 3-28 ton
Commercial
HOSPITALITY
REBEL APPLIED™
DPSA 20-52 ton
Packaged
MAVERICK® II
MPS 26-75 ton
Commercial
ROOFPAK® 45-150 ton
RPS
Applied
10 30 50 70 90 110 130 150
Tons 0 20 40 60 80 100 120 140
10
MODEL MPS PERFORMANCE
COOLING & HEAT PUMP Cooling and heat pump
MAVERICK® I 3-25 tons
1,000-10,000 cfm
Maverick I rooftops are dependable and cost-effective due to efficient R-410A
scroll compressors, integrated blower control, and easy-to-access
mechanical components that reduce service costs. 15 IEER
FEATURES
Modular, 34.5
maximum sections
MERV 7, 8, 11, 13 or 14
filtration
Variable and constant
air volume configurations
Free cooling economizer
PERFORMANCE
MODEL DPS
Cooling and heat pump
COOLING & HEAT PUMP
3-28 tons
Up to 10,500 cfm
REBEL®
Rebel provides building owners with energy savings up to 43% above
R-410A
ASHRAE’s 90.1 2016 standard, enabling complete system payback
20.6 IEER in under two years.
FEATURES
Variable speed Daikin
inverter compressor
100% dedicated outdoor
air system (DOAS)
Direct-drive, variable
speed ECM or VFD
fan motors
Variable speed
heat pump
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 11
MODELS DPSA/DFSA
PERFORMANCE
Heating and cooling HEATING & COOLING
20-52 tons
REBEL APPLIED™
5,000-21,000 cfm
R-410A Rebel Appled is an all-encompassing packaged rooftop solution
that rises above its class with industry-leading high-performance
Up to 20.0 IEER design, maximum energy efficiency, lowest lifecycle cost and
unlimited configurability.
FEATURES
R-13, double-wall foam,
integral thermal break
Low casing up to 5” of
static pressure
37% shorter, 30% lighter
than legacy rooftops
Modular construction
simplifies retrofits
Inverter Scroll Compressors Sorbent Ventilation Technology Unmatched Retrofit Capabilities
12
MODEL MPS PERFORMANCE
HEATING & COOLING Heating and cooling
MAVERICK® II 26-75 tons
6,000-28,000 cfm
Maverick II rooftops arrive as a complete packaged solution, R-410A
maximizing design and installed cost savings with a wide-range of
factory-installed options. 10.0+ IEER
FEATURES
Variable or constant
air volume operation
Energy recovery reduces
energy costs
Double-wall construction
with access doors
Gas heat with staged or
modulating control
MODELS RPS/RFS/RDT/RCS
PERFORMANCE
Heating and cooling HEATING & COOLING
45-150 tons
ROOFPAK®
5,000-50,000 cfm
RoofPak combines the lower installation costs and interior
R-410A space savings of a roof-mounted system with the operating and
Seismic certified maintenance efficiencies of central heating and cooling systems.
FEATURES
Modular construction,
walk-in access
Energy recovery
reduces energy costs
Factory-integrated
options & flexibility
Easy BAS integration
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 13
COILS
Daikin coils offer the widest variety of materials, physical sizes, fin spacings, row depths and
circuiting. Hi-F (high-efficiency) fins maximize heat transfer with fewer fins to lower your initial
cost. E-F (energy-efficient) fins save energy by reducing air pressure drop as much as 33%, while
also lowering fan brake horsepower requirements.
NAME/MODEL:
CHILLED
WATER
5WQ/5MH/5MS/5WH/5WS/
5WM/5WD
5WQ 5WH 5WL 5WS 5WM 5WD
EVAPORATOR
5EN/5EF/5ER/5EJ/5EK
5EN 5ER 5EF 5EJ/5EK
HOT WATER
5MQ/5MH/5MS/5WB/5WQ/5WH/
5WL/5WS/5WM/5WD
5WQ 5WH 5WH 5WS 5MQ/5MH/5MS
BOOSTER
5BB/5BS/5BD
5BS 5BB 5BD
STEAM
5SA/5HA/5JA/5GA/
8JA/8GA/8RA/8TA
5SA/5HA 5JA/5GA/8JA/8GA 8RA/8TA Directional orifice
14
FINS HI-F5/E-F5 PERFORMANCE
WATER COOLING/ 300°F maximum
EVAPORATIVE
2-12 rows
Up to 200 psig
Cooling coils are designed for use with chilled or well water in 5/8” copper tubing
comfort cooling, process, dehumidifying and special applications. Up to 14 fins per inch
Evaporative coils deliver the maximum heat transfer under all
operating conditions and are excellent for comfort cooling, process FEATURES
integration and dehumidification.
AHRI Standard 410
certified
Staggered design for
increased cooling
Factory leak tested
at 315 psig
Vents and drains
on all water coils
FINS HI-F5/HI-F8/E-F5
PERFORMANCE
400°F maximum
WATER HEATING/
BOOSTER/STEAM
1-12 rows
Up to 250 psig
5/8” and 1” copper tubing Heating coils produce high capacities with limited water quantities,
Up to 14 fins per inch while booster coils are designed for use in reheat applications in
constrained spaces. Our interchangeable steam coils with optimal fin
FEATURES design serve both general and special-purpose applications with
high-performing heat transfer capabilities.
AHRI Standard 410
certified
Staggered design for
increased heating
Factory leak tested
at 315 psig
Vents and drains
on all water coils
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 15
CONDENSING UNITS
SOLUTIONS TO MATCH YOUR PRIORITY
Daikin Applied offers a wide range of air-cooled, split system condensing units with abundant
options to meet efficiency, performance or serviceability requirements. Our condensing units
meet ASHRAE 90.1 efficiencies, run quietly and provide low-ambient operation range down to 0°F.
APPLICATIONS
HEALTHCARE
OFFICE BUILDINGS
SCHOOLS
MANUFACTURING
RETAIL
NAME/MODEL:
COMMERCIAL
SPLIT SYSTEM 6-20 ton
RCS
R-410A Air-cooled
APPLIED
SPLIT SYSTEM 25-135 ton
RCS
R-22/R-407C Air-cooled
APPLIED
SPLIT SYSTEM 15-140 ton
RCS
R-410A Air-cooled
10 30 50 70 90 110 130
Tons 0 20 40 60 80 100 120 140
16
MODEL RCS PERFORMANCE
R-410A COMMERCIAL Operates down to 0°F
SPLIT SYSTEM
6-20 tons
2-stages (10+ tons)
Commercial split sytems are dependable and cost-effective due 1 refrig. circuit
to efficient scroll compressors and easy-to-access mechanical Meets min. efficiencies
components that reduce service costs.
FEATURES
Salt spray
resistant exterior
Small footprint
Pairs with PreciseLine
air handlers
Low cost, economical
commercial solution
MODEL RCS
PERFORMANCE
Operates down to 0°F
R-410A & R-22/R-407C
APPLIED SPLIT SYSTEM
15-140 tons
Head pressure control
2 refrig. circuits Designed for quiet and energy efficient operation that meets
Up to 15.4 EER ASHRAE 90.1 efficiency requirements, RCS split sytems can be
combined with Daikin air handlers and coils to match exact job
FEATURES application requirements.
Micro-channel coils -
(R-410A units)
Redundant dual
refrigerant circuits
Quiet, vertical
condenser fans
Mulitple stages of
capacity control
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 17
AIR HANDLERS
COMPLETE, ULTIMATE FLEXIBILITY
Daikin Applied indoor and outdoor air handlers are used to condition and circulate large volumes of air
throughout a space via ductwork and are part of a system using either a chiller with cooled water or a
condensing unit in a direct expansion (DX) system.
NAME/MODEL:
APPLICATIONS
PRECISELINE® HEALTHCARE
BCH/BCA/BCV
Indoor
600-10,000 cfm
OFFICE BUILDINGS
SCHOOLS
REBEL® 500-11,500 cfm
DAH
Outdoor Chilled Water MUSEUMS
GOVERNMENT
ROOFPAK®
RAH/RDS 4,000-50,000 cfm
Outdoor
SKYLINE®
OAC/OAH 900-51,000 cfm
Outdoor
VISION®
CAC/CAH 900-84,500 cfm
Indoor
Custom 900-84,500 cfm
CAC/CAH/OAC/OAH
Indoor/Outdoor
10k 30k 50k 70k 90k 110k 130k
CFM 0 20k 40k 60k 80k 100k 120k
18
MODELS BCV/BCA/BCH PERFORMANCE
INDOOR R-6.5
PRECISELINE®
006-050 sizes
600-10,000 cfm
PreciseLine’s compact vertical and horizontal configurations give .5-133 kW elect. heat
system designers and contractors unmatched design capability when MERV 8 or 13 filtration
faced with tight space restrictions.
FEATURES
DOAS/VRV integration
Factory-installed valve
and piping packages
Double wall, 1” foam
thermal panels
Economizer mixing
box option
MODEL DAH
PERFORMANCE
R-13
OUTDOOR
CHILLED WATER
003-021 sizes
500-11,500 cfm
6-140 kW elect. heat
REBEL®
30% more efficiency
When combined with Daikin Applied air-cooled chillers, Rebel offers
FEATURES engineers and building owners a chilled water solution featuring
technologies that provide for a complete single-sourced system..
Variable speed ECM
or direct-drive fans
Optional factory-
installed valves
Quiet, double-wall
foam cabinet
2” and 4” slide-out
filter racks
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 19
MODEL RAH/RDS
PERFORMANCE
R-6.5
OUTDOOR
ROOFPAK®
006-050 sizes
4,000-50,000 cfm
Blow/draw-through coils RoofPak is a preferred HVAC solution for building projects that want
to capitalize on decades of innovation, design flexibility and durable
MERV 8 and 13 filtration construction expertise that yields low capital and operating costs.
FEATURES
Modular construction,
walk-in access
100% DOAS, VAV or
CAV operation
Independant IBC seismic
certification
Easy BAS integration
MODELS OAC/OAH
PERFORMANCE
OUTDOOR R-13
SKYLINE®
003-090 sizes
900-51,000 cfm
Skyline’s modular platform construction featuring 2-inch Blow/draw-through coils
incremental dimensioning gives engineers unlimited design MERV 8-17 filtration
capabilities to incorporate valuable features and options to
specifically match application requirements. FEATURES
Sorbent Ventilation
Technology (SVT)
Space-saving
ECM fan array
Modular design
flexibility
Fixed plate or energy
recovery wheel
20
MODELS CAC/CAH PERFORMANCE
INDOOR R-13
VISION®
003-169 sizes
900-84,500 cfm
Vision meets demands for improved indoor air quality, low sound, Blow/draw-through coils
high operating efficiency and smaller mechanical rooms with
MERV 8-17 filtration
patented construction that provides unequaled thermal efficiencies
and low leakage rates. FEATURES
Sorbent Ventilation
Technology (SVT)
Space-saving
ECM fan array
Modular design
flexiblity
Fixed plate or energy
recovery wheel
MODELS CAC/CAH/OAC/OAH
PERFORMANCE
R-13
INDOOR/OUTDOOR
CUSTOM
003-169 sizes
900-84,500 cfm
Blow/draw-through coils With the ability to attain a maximum of Class 6 leakage, Daikin
+/-8” static pressure custom air handlers provide the ultimate in design flexibility and
turn-key solutions for increased filtration in healthcare facilities,
FEATURES clean rooms or labs.
Sorbent Ventilation
Technology (SVT)
Space-saving
ECM fan array
Factory options for
customized flexibility
HEPA, PCO, gas phase &
low pressure filtration
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 21
WATER-COOLED CHILLERS
ENERGY SAVINGS BUILDING OWNERS DEMAND
Chillers make cold water or water/glycol fluid mixture to cool buildings or processes. A water-cooled
chiller rejects the absorbed heat to an additional fluid loop that can then reject the heat through
a secondary device such as a cooling tower or dry cooler.
NAME/MODEL:
APPLICATIONS
WATER-COOLED 30-200 tons
WGZ
Scroll compressor HEALTHCARE
OFFICE BUILDINGS
NAVIGATOR® 120-300 tons SCHOOLS
WWV
Screw compressor
MANUFACTURING
DATA CENTERS
TEMPLIFIER® 15-1,200 tons
TGZ/TSC
Heat recovery water heaters
MAGNITUDE® 86-1,600 tons
WMC,/WME
Magnetic bearing compressor
CENTRIFUGAL
WSC 300-1,350 tons
Single compressor
CENTRIFUGAL 600-2,700 tons
WDC/WCC
Dual compressor
50 250 750 1250 1750 2250 2750
Tons 0 100 500 1000 1500 2000 2500 3000
22
MODEL WGZ
PERFORMANCE
SCROLL COMPRESSOR R-410A
WATER-COOLED
30-200 tons
72 dBA
Shipped complete, these units are among the quietest and most 56-352 gpm
reliable chillers available today. Their efficient and quiet operation
Up to 21.3 IPLV
is ideal for sound-sensitive, water-cooled, remote air-cooled or
evaporative condenser applications. FEATURES
Vibration isolators for
quiet operation
Controls flexibility with
easy BAS integration
Fits through standard
door openings
Advanced DDC controls
MODEL WWV
PERFORMANCE
R-134a
SCREW COMPRESSOR
NAVIGATOR®
120-300 tons
422-1,055 kW
0.36 kW/ton IPLV Navigator integrates variable volume ratio (VVR®) compressor
35 second restart technology to give you the advantage of a system that is quiet, while
adapting to real-time building demands for the most efficient and
FEATURES cost-saving operation possible.
RapidRestore® and
Fast Loading
Variable volume ratio
(VVR) technology
Integrated variable
frequency drive (VFD)
Easily integrates into
BAS of choice
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 23
MODEL TGZ/TSC
PERFORMANCE
R-134a
HEAT RECOVERY
TEMPLIFIER®
15-1,200 tons
52-4,220 kW
Up to 160°F water Templifier recovers large amounts of heat that would
typically be rejected from the building and then use that heat for
600-18,000 MBh
processes, building heat, or domestic hot water. They offer
FEATURES significant environmental advantages over boilers or electric heat
for greener building solutions.
Economical hot
water heating
Off-loads boilers &
cooling towers
No ozone depleting
refrigerant
Reduced chemical
treatment costs
MODELS WMC/WME
PERFORMANCE
MAGNETIC BEARING R-134a or R-513A
MAGNITUDE®
86-1,600 tons
302-5,627 kW
Magnitude is up to 40% more efficient than standard centrifugal 40% more efficient
chillers and can save up to $4 million over the life of the chiller. 17 sec. power restore
Quiet operation and proven reliability across the world’s largest
installed base of chillers make Magnitude the preferred choice for FEATURES
all types of building applications.
Rapid Restore® and Ride-
Through® technology
Oil-free, magnetic bearing
technology
Efficient variable
frequency drives (VFDs)
2” incremental
dimensioning design
24
MODEL WSC
PERFORMANCE
SINGLE COMPRESSOR R-134a or R-513A
CENTRIFUGAL
300-1,350 tons
1,050-4,750 kW
These chillers easily integrate with building automation systems, are Lowest part-load kW
seismic compliant, quiet and have a wide operating range to allow
operation at varying lift conditions. Knockdown allows entry into tight
areas for both new and replacement applications. FEATURES
Smallest footprint per
ton optimizes space
Easy disassembles and
reassembles at site
Non-ozone depleting
refrigerant
Seismic certified
MODELS WDC/WCC
PERFORMANCE
R-134a or R-513A
DUAL COMPRESSOR
CENTRIFUGAL
600-2,700 tons
2,110-9,500 kW
Lowest part-load kW Dual compressor chillers offer excellent full and part-load
performance for increased energy savings and system redundancy,
similar to two separate chillers, with a lower total-installed cost.
FEATURES
35% cost savings over
multiple chillers
Built in redundancy
reduces downtime
Non-ozone depleting
refrigerant
Seismic certified
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 25
AIR-COOLED CHILLERS
COMPLETE, ULTIMATE FLEXIBILITY
Chillers make cold water or water/glycol fluid mixture to cool buildings or processes. An air cooled
chiller rejects the heat absorbed from the building or process directly to the outdoor air using
refrigerant to air coils and fans that blow outdoor air directly over those coils.
APPLICATIONS
HEALTHCARE
OFFICE BUILDINGS
HIGHER EDUCATION
HOSPITALITY
DATA CENTERS
NAME/MODEL:
TRAILBLAZER® 10-40 tons
AMZ/EWYQ (25 ton)
Scroll compressor
TRAILBLAZER® 30-240 tons
AGZ
Scroll compressor
PATHFINDER® 100-565 tons
AWV
Screw compressor
50 150 250 350 450 550 650
Tons 0 100 200 300 400 500 600
26
MODELS AGZ/AMZ/EWYQ
PERFORMANCE
SCROLL COMPRESSOR R-410A
TRAILBLAZER®
10-240 tons
35-800 kW
Trailblazer® provides 10% more efficiency than leading competitors at 45% heat recovery
design and off-design conditions. With a broad tonnage range, it gives
Up to 16.7 IPLV
you the scale to fit your cooling needs and offers the best overall
value in air-cooled packaged chillers available. FEATURES
Quiet operation as low
as 61 dBa
RapidRestore® full
power in <4 minutes
Easy inegration with
BAS of choice
Compact unit footprint
MODEL EWYQ
FEATURES
HEAT PUMP!
MODEL AWV
PERFORMANCE
R-134a or R-513A
SCREW COMPRESSOR
PATHFINDER®
100-565 tons
350-1,985 kW
Up to 60% more efficient The 100% configurable, free-cooling Pathfinder is the most efficient
+22 IPLV machine on the market today – the first air-cooled screw chiller
with IPLVs exceeding 22 EER. It includes an array of features that
FEATURES optimize sound, and deliver the lowest turndown in flow and highest
leaving chilled water capabilities.
Variable volume ratio
(VVR) technology
Integrated free cooling
economizer
RapidRestore® and Fast
Loading technology
100% fully configurable
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 27
MODULAR CENTRAL PLANT (MCP)
SCALABLE SOLUTIONS TO ACCOMODATE EXPANSION
When building for today with an eye toward tomorrow, pick a scalable solution that can accommo-
date expansion in the years ahead. A Daikin MCP is a complete central plant including all components:
chillers, boilers, domestic hot water, pumps, piping, electrical, controls and cooling towers.
MODEL MCP
BENEFITS
MODULAR 100% turnkey
SOLUTIONS
Fits specific footprint
Meets fast-track jobs
Each modular central plant (MCP) is custom designed and fabricated Lowest cost per ton
in our production facility by a certified team for your specific project. Custom engineered
Before shipping to the installation site, each MCP is fully assembled
and tested in the factory. SOLUTIONS
Modular construction,
easy walk-in access
Complete management
through delivery
Simplified single-source
responsibility
Scalable for ongoing
building expansions
28
SITELINE™ BUILDING CONTROLS
MAKING AUTOMATION SIMPLE
Whether you’re overseeing a complex HVAC ecosystem of equipment and buildings or monitoring
standalone units, SiteLine Building Controls and Service Solutions will help you create comfortable
and sustainable environments where tenants work and live.
MODELS SDE/SWL/SPP
BENEFITS
Increases efficiency
EQUIPMENT & BAS
CONNECTIVITY
Improves operations
Optimizes IAQ
Measures carbon goals SiteLine’s scalable, cloud-based equipment and building automation
Keeps tenants cool systems (BAS) instantly and easily optimize the performance of
Daikin HVAC units and any HVAC ecosystem - including other makes
SOLUTIONS and existing building systems. You’ll get real-time analytics that
provide effortless insight and optimization for energy, indoor air
Preventive alerts to quality and sustainability.
reduce downtime
Scalable for equipment
and buildings
Remote monitoring from
any device, anywhere
• Dedicated
Advanced security to Equipment
protect data • Wireless BAS
• Pre-programmed
BAS
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 29
UNIT HEATERS/FAN COILS
PERFORMANCE YOU DEMAND. QUALITY YOU EXPECT.
For over 80 years, building owners, facility managers, and specifying engineers have turned to
Daikin unit heaters and fan coils to meet and surpass their most desired requirements, with
options and sizing to meet room application and conditions.
APPLICATIONS
NAME/MODEL:
HOSPITALITY
CABINET
UNIT HEATERS 18-610 Mbh GOVERNMENT
UHH/UDH
HEALTHCARE
SCHOOLS
Mbh 0 200 400 600
OFFICES
NAME/MODEL:
THINLINE
FCH*/FCV*/FHV*/FHW*/FHH*
Flat/Slope Top, Concealed,
Recessed, Exposed
200-1,200 cfm
OPTILINE™ 300-1,200 cfm
FSG
Vertical Stacked
CFM 0 250 500 750 1000 1250 1500
30
MODELS UHH/UDH
PERFORMANCE
CABINET 18-610 Mbh heating
UNIT HEATERS
018-610 sizes
1/2-6 tons
Daikin horizontal and vertical cabinet unit heaters provide 310-12,350 cfm
specifying engineers and facility managers with simple heating
Sound class I-VII
solutions for industrial and commercial applications to meet specific
heat-throw and heat-spread requirements. FEATURES
1/2” copper coils,
aluminum fins
150 psig steam or
220 psig hot water
Intermittent or
continuous fan
Standard 115/60/1
PSC motors
MODELS FCH*/FCV*/FHV*/FHW*/FHH*
PERFORMANCE
20.9-144.1 Mbh heating
HORIZONTAL/VERTICAL
THINLINE
002-012 sizes
0.5-10.0 kW elect. heat
200-1,200 cfm ThinLine horizontal units offer space savings for single-zone
80% higher efficiencies applications in new or retrofit buildings, with extensive design
and color choices allow them to blend into all types of building
FEATURES environments and decor.
100+ factory valve and
piping packages
2, 3 and 4-row
primary coils
Energy-saving EC
fan motors
ASHRAE 62.1-2010
compliant
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 31
MODEL FSG
PERFORMANCE
R-6.5
VERTICAL STACKED
OPTILINE®
003-012 sizes
9-38.2 Mbh
300-1,200 cfm With the smallest footprint in the industry, OptiLine is the ideal
retrofit or new construction solution when livable and working
NC less than 30
space is at a premium.
FEATURES
Smallest footprint
in the industry
3 or 4-row primary
heating coil
Energy-saving EC
fan motor
Primary or auxiliary
electric heat
32
AIR PURIFIER
HEPA AND MERV 13 FILTRATION
Designed to improve indoor air quality (IAQ) and help reduce the risk of airborne contaminants
within indoor spaces, the Air Purifier’s simple design blends nicely with just about any décor
scheme.
MODEL DAP
PERFORMANCE
99.97% contaminant free
PREMIUM & ECONOMY
AIR PURIFIER
250 and 750W output
500 and 1,000 cfm
5.5 and 14.75A draw Premium air purifier models feature a HEPA post filter and economy
.33 and 1HP EC motor models feature a MERV 13 post filter that meets ASHRAE minimum
In-Room Air Cleaning Guidance recommendations. Each unit arrives
FEATURES fully assembled from the factory for immediate installation.
MERV 8, MERV 13 and
HEPA filtration
Factory assembled and
tested
3-speed dial with
customizable settings
High-efficiency EC motor
ECONOMY PREMIUM
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 33
WATER SOURCE HEAT PUMPS
UNMATCHED PERFORMANCE AND OCCUPANT COMFORT
Daikin water source heat pump systems (WSHPs) are some of the most efficient, environmentally-friendly
systems available for heating and cooling buildings. These high-efficiency, self-contained units are
available in a variety of sizes/configurations and can be placed in virtually any location within a building.
NAME/MODEL:
APPLICATIONS
SMARTSOURCE® 600-4,000 cfm
DOAS
WGOV CONDOMINIUMS
GOVERNMENT
ENFINITY ®
1/2-1-1/2 ton
MHC/MHW SCHOOLS
Console
DATA CENTERS
VERTICAL STACK 3/4-3 ton OFFICE BUILDINGS
VHF/VHC/VHW
Vertical Stack
ENFINITY® 1/2-6 ton
CCH/CCW/VFC/VFW
Horizontal & Vertical
SMARTSOURCE®
COMPACT 1/2-6 ton
GCV/GCH/GDH
Horizontal & Vertical
SMARTSOURCE® 1/2ton
1/2-6 — 6 ton
GSH/GTH/GSV/GTV
Horizontal & Vertical
ENFINITY® 6-25 ton
CCH/CCW/LVC/LVW
Lg. Capacity, Horizontal & Vertical
Tons 0 5 10 15 20 25
34
MODEL WGOV
PERFORMANCE
DOAS DAT control to ±1°
SMARTSOURCE®
008-024 sizes
600-4,000 cfm
Dedicated outside air systems (DOAS) bring the outside in by 30-100% capacity control
drawing 100% outside air through the unit and into a building’s
5.1 ISCOP
HVAC system to improve indoor air quality.
FEATURES
Constant or variable
air volume
Field programmable
airflow levels
Reheat dehumidification/
SmartBoost heating
Advanced DDC controls
MODELS MHC/MHW
PERFORMANCE
9000-19,000 nom. cooling
CONSOLE
ENFINITY®
1/2-11/2 tons
007-018 sizes
Up to 4.97 COP Enfinity combines slope top or flat top cabinet design, high-sill or
Up to 31.3 EER low-sill configuration, and a variety of color selections and options
that allow greater flexibility to design, install, operate, and maintain
FEATURES an optimum WSHP system for any new or replacement project.
Standard or geothermal
flexibility
Quiet GentleFlo® fan
operation
LonWorks® or BACnet®
communication
Flat top or slope top
confguration
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 35
MODELS VHF/VHC/VHW
PERFORMANCE
R-6.5
VERTICAL
STACK
009-036 sizes
3/4-3 tons
300-1,200 cfm Vertical stack units are readily
available in full-cabinet design
16.8 EER for use in new installations, or
as a stand-alone chassis design
FEATURES
for quick changeouts needed in
Hydronic heat and replacement applications.
geothermal options
Efficient and quiet
EC fan motors
MERV 8 or 13
filtration
Motorized outdoor air
damper
MODELS CCH/CCW/VFC/VFW
PERFORMANCE
HORIZONTAL & VERTICAL 30°-110°F entering water
ENFINITY®
007-070 sizes
1/2-6 tons
Designed for high efficiency, individually-zoned comfort 250-2,600 cfm
control, small-footprint Enfinity units free up valuable space Up to 19.6 EER
and incorporate a bevy of cost-saving, low maintenance
features in flexible cabinet configurations. FEATURES
Standard or geothermal
configurations
Highly optioned to
match applications
Superior IAQ and
quiet operation
LonWorks® or BACnet®
communication
36
MODELS GCV/GCH/GDH
PERFORMANCE
COMPACT 6,200-71,000 Btu cooling
SMARTSOURCE®
007-070 sizes
1/2-6 tons
Compact vertical and horizontal configurations give system designers 250-2,160 cfm
and contractors unmatched design capability when faced with tight
Up to 19.0 EER
space restrictions.
FEATURES
Small-scale, serviceable
design
EC fan motors with
adjustable air flow
Energy-saving
waterside economizer
MERV-8 and MERV-13
filtration
MODELS GSH/GTH/GSV/GTV
PERFORMANCE
8,000-73,400 Btu cooling
HORIZONTAL & VERTICAL
SMARTSOURCE®
007-072 sizes
1/2-6 tons
250-2,160 cfm SmartSource horizontal and vertical units combine industry-leading
Up to 28.9 EER efficiences with low-noise operation, high indoor air quality and
consistent air temperatures for unmatched WSHP performance.
FEATURES
Single or dual-stage
operation
Quiet operation, low
energy consumption
Smart Dehumidification,
precise humidity control
Fiber-free indoor
air quality
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 37
MODELS CCH/LVC
PERFORMANCE
R-6.5
LARGE CAPACITY
ENFINITY®
6-25 tons
072 to 290 sizes
1,800-11,500 cfm Large capacity units are easily adaptable to fit in small equipment
rooms or floor-by-floor installations. They can be applied to all building
Up to 17.1 EER types where it is advantageous to extend the water source heat pump
concept to larger or core areas.
FEATURES
Standard or geothermal
configurations
Highly optioned to
match applications
Superior IAQ and
quiet operation
LonWorks® or BACnet®
communication
38
VARIABLE AIR VOLUME (VAV)
SETTING THE STANDARD FOR QUALITY AND PERFORMANCE
Daikin’s single-duct VAV boxes provide high performance and set the standard in the industry for
construction, performance, and quality. Daikin fan-powered terminal units, available as parallel
and series, provide operating cost savings through reduced central fan horsepower and through
waste heat recovery.
MODELS MQTHI5/MQFCI6/MQFVI5
PERFORMANCE
Hot water/elect. heat
SINGLE-DUCT & FAN
TERMINAL UNITS
10 unit sizes
80-8,000 cfm
Up to 3” w.g. static press. Single-duct terminal units regulate conditioned air flow into an occupied
AHRI certified zone in response to a control signal, while fan-powered terminal units are
typically used for heating and cooling perimeter zones.
FEATURES
Reliable and efficient
scroll compressors
LonTalk® or BACnet®
communications
Economizer with
low-leak dampers
Easy access to
components
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 39
UNIT VENTILATORS
REDUCING COST WHILE MATCHING COMFORT
Unit ventilators minimize energy usage by utilizing a two-stage compressor and multi-speed fan to
better match changing room loads. They leverage “free” cooling opportunities to reduce operating
costs. During unoccupied periods and at night, units operate sparingly to conserve energy.
APPLICATIONS
SCHOOLS
OFFICE BUILDINGS
HEALTHCARE
RETAIL
HOSPITALITY
NAME/MODEL:
HEAT PUMP 650-1,500 cfm
AEQ, ARQ, GRQ
Air & Water
CLASSROOM 1,000-1,500 cfm
AZQ, AZR, AZU
Vertical
CEILING/FLOOR
AHF, AHB, AHV, AHR, 525-2,000 cfm
AVS, AVB, AVV, AVR
Horizontal & Vertical
150 450 750 1050 1350 1650 1950
Tons 0 300 600 900 1200 1500 1800 2100
40
MODELS AEQ/ARQ/GRQ
PERFORMANCE
AIR & WATER 16,500-51,200 Btuh
HEAT PUMP
024-048 sizes
650-1,500 cfm
Heat pump unit ventilators utilize the natural properties of the Draw-through coils
earth to provide heating and cooling to a building. Heat addition and
Up to 20.9 EER
rejection occurs below the ground, inside hundreds of feet of ground
loop where fluid is circulated through the loop and then back to the FEATURES
ventilator unit.
Dampers for superior
temp./humidity control
GentleFlo® air moving
for quiet operation
Easy integration of unit
controllers by others
Free cooling economizer
operation
MODELS AZQ/AZR/AZU
PERFORMANCE
21,000-52,300 Btuh
VERTICAL
CLASSROOM
024-054 sizes
1,000-1,500 cfm
Draw-through coils Classroom unit ventilators feature precise temperature and
Up to 12.7 EER dehumidification control to help keep students and teachers
comfortable while making maximum use of free outdoor-air cooling
FEATURES to reduce operating costs.
Dampers for superior
temp./humidity control
GentleFlo® air moving
for quiet operation
Easy integration of unit
controllers by others
Heat transfer coil
provides extra capacity
© 2023 DAIKIN APPLIED | (800) 432.1342 | WWW.DAIKINAPPLIED.COM 41
MODELS AH*/AV*
PERFORMANCE
15,700-57,600 Btuh
HORIZONTAL/VERTICAL
CEILING/FLOOR
007-015 sizes
525-2,000 cfm
Draw-through coils Ceiling and floor units are perfect for new construction and for
retrofit applications. Older buildings with baseboard radiant heat
2-5 cooling rows or other hydronic heating systems can be easily adapted to work
efficiently with these units.
FEATURES
Bypass damper for
temp./humidity control
VRV integrated option
Easy integration of unit
controllers by others
Free cooling with
economizer
42
PROTECTIVE
MAINTENANCE PLANS
Ensure peak performance and protect your building’s most
valuable asset - your HVAC system, with a customized
maintenance plan from Daikin. Whether installing new
equipment or optimizing an existing system, our factory-
trained technicians can deliver regular, preventative care to
maximize efficiency, extend equipment life, and identify issues
early, saving you time and money. With seasonal startups
and shutdowns, comprehensive system checks, and detailed
reporting, trust Daikin specialists for complete peace of mind
ensuring that your HVAC investment is protected.
CUSTOMER BENEFITS INCUDE
EXTEND EQUIPMENT LIFE MINIMIZE CATASTROPHIC EVENTS
Our factory trained technicians perform all vital Predictive maintenance services anticipate potential
maintenance on a planned schedule to ensure peak equipment failures to mitigate the risk of catastrophic
efficiency, extending the life of your HVAC equipment. events.
ENSURE PROACTIVE EQUIPMENT MAINTENANCE 24/7 EMERGENCY SERVICE AND SUPPORT
Daikin’s proven experts provide trusted support and When breakdowns happen, time is of the essence.
ensure you get the help you need to prepare for We can provide emergency support whenever,
upcoming equipment maintenance. wherever, and however you need us.
LEARN MORE AT DAIKINAPPLIED.COM OR CONTACT YOUR LOCAL SERVICE REPRESENTATIVE
© 2024 DAIKIN APPLIED | (800) 432.1342 | ASP 31-564
PROTECTIVE PLANS FOR YOUR HVAC INVESTMENT
FIRST-YEAR MAINTENANCE PLAN INSPECTION MAINTENANCE PLAN
Take the work and worry out of equipment Extend the lifespan of your HVAC system through
maintenance during the critical warranty period. Get consistent, scheduled upkeep. Our inspection
vital preventative service from our expert technicians & maintenance plan ensures your equipment
to ensure warranty protection and optimize your HVAC undergoes regular maintenance and inspections by
factory-trained technicians, who can collaborate
investment from day one. With maintenance matched
seamlessly with your on-site staff. Also, you can
to your schedule, Daikin cares for your new equipment
benefit from an affordable payment plan, making it
or HVAC system so you can be confident it’s operating
easier to manage your maintenance budget.
at peak efficiency.
LABOR MAINTENANCE PLAN COMPREHENSIVE MAINTENANCE PLAN
Labor maintenance plans are a tailor-made, adaptable This all-inclusive service plan offers unparalleled
approach designed to safeguard your HVAC equipment. support for your most valuable building asset. It
This plan encompasses all labor costs for repairs within the covers all necessary labor, parts, materials, and
covered services, ensuring your system always performs at its refrigerants for the selected services, ensuring no
best through regularly scheduled maintenance. Your staff will unexpected expenses. Enjoy 24-hour priority service,
routine maintenance, and inspection services, all
also benefit from on-site operational guidance provided by
under one plan designed to prevent budgetary
Daikin’s technicians.
surprises.
PLAN MATRIX
FIRST-YEAR INSPECTION & LABOR COMPREHENSIVE
PLANS MAINTENANCE MAINTENANCE MAINTENANCE MAINTENANCE
REGULAR SCHEDULED
SERVICE
SEASONAL STARTUP &
SHUTDOWN
ON-SITE SYSTEM
EVALUATION
OPERATIONAL
INSTRUCTION
TECHNICAL
SUPPORT
PREFFERED
SERVICE
24-HOUR SERVICE
AVAILABILITY OPTIONAL OPTIONAL
ANNUAL CONDENSER
CLEANING OPTIONAL OPTIONAL
REPAIR LABOR
COSTS INCLUDED
PARTS, MATERIALS &
REFRIGERANTS INCLUDED
REMOTE MONITORING
& INSPECTIONS OPTIONAL OPTIONAL OPTIONAL OPTIONAL
OUR BRAND PROMISE
At Daikin, our goal is to make the time you
spend indoors as productive and pleasant as
possible, with superior comfort and quality air. We deliver extraordinary results for remarkable value. This means
Let us help you build convenience, confidence being ready for you whenever, wherever and however you need
and excellence into your buildings, and free us. Your Daikin Service team is on standby with well-outfitted
up your people to work toward your mission. local resources that are backed by the world’s number one air
Whether you need immediate service, routine conditioning company. Whether you’re looking to extend the
maintenance or an expert consultant, Daikin life of your equipment or to drive efficiency into every aspect of
is here to help. Daikin Service will make your business, our team will identify the solutions to meet you
your building the second best performing where you are today and take you where you want to go.
employee that props up everyone else.
REPLACEMENTS
BUILDING
MODERNIZE ASSESSMENTS
OPTIMIZE RENTALS
DAIKIN360 INTEGRATED SERVICE SOLUTIONS
We understand that your building is one of your company’s most significant investments, and a cornerstone of growth
and success. Our expertise in HVAC systems, delivered through Daikin360 Integrated Service Solutions, can help make
MAINTAIN
your building &
your second-best PARTS
employee by creating an ideal environment and quality air that propels & people and
your
REPAIR Plus, our advanced energy-saving solutions and protective maintenance plansSUPPLIES
customers forward. can help you control
your maintenance and operational costs. You can countANALYSIS
on Daikin Applied for advanced technology, agility and reliability.
Whenever, Wherever, However You Need Us.
REPLACEMENTS
BUILDING
MODERNIZE ASSESSMENTS
OPTIMIZE RENTALS
MAINTAIN & PARTS &
REPAIR SUPPLIES
Whenever,
LEARN MOREWherever, However
ABOUT DAIKIN360 You
SERVICE Need Us.
OFFERINGS
AT DAIKINAPPLIED.COM/360-SERVICE-SOLUTIONS
SERVICE SOLUTIONS PROGRAMS
PROGRAM CARD
KEY BENEFITS NEW ADDED PARTS TARGET UNIT AGE
- Upgraded to the latest C Vintage
GEN 1 Technology (Major Rebuild) - Compressor All vintage A units
UPGRADE -
MAJOR COMPONENTS
2 Year P&L Warranty - VFD Power Box (2010-2016)
WME
- New Serial Number & nameplate - Control Platform
- Boosted Reliability for uninterrupted
COMPRESSOR - Compressor Carbon
operation 5 YR Intervals
GROUNDING -
MAJOR COMPONENTS
Protection for compressor components Grounding uRod
ROD - Extended Operation Longevity
- Enhance operational efficiency and Soft Start Module; Capacitors & - 8-17 YO units
MAJOR COMPONENTS
prolong equipment lifespan. Buss Bar Assy; IGV Drive Assy,
IGBT Snubber; Soft Start Cooling - Or 50,000 run
CAP
(CHILLER ASSURANCE -
(Compressor Rebuild)
2 Year P&L Warranty KEY BENEFITS
Fan Assy; High & Low-Pressure hours
PROGRAM) - New Serial Number & nameplate Transducers; Solenoid Plunger
Assy; Cavity Temperature Sensor;
Front & Rear Bearing: Sensor
Cable Harness, Bearing Sensor
WMC
Feed Throughs, Feed Throughs.
CHILLER - Larger HMI display - HMI Kit
CONTROLS - Improved Data Layout
MAJOR COMPONENTS - PCO5 Controllers 2004-2020
UPGRADE - Improved Control Technology (Unit & Compressors)
- User friendly
- 2014-2017: Compressor, Parts
- Low GWP Kit (gaskets & valve) , R-513A
R-513A
- MAJOR
Reduction COMPONENTS
in Carbon Footprint Refrigerant)
REFRIGERANT - Confidence in Compliance - 2018-2020: Parts Kit (gaskets
2014-2023
RETROFIT - Operator and Facility Safety and valve), R-513A Refrigerant)
- 2021-2023: Parts (gaskets and
valve), 513A Refrigerant)
- Enhance operational efficiency and - Dependent on Open
prolong equipment lifespan. Compressor Inspection - 8-17 YO units
CAP Findings.
(CHILLER ASSURANCE (Compressor Rebuild) - Or 50,000 run
- 2 YearMAJOR
P&L Warranty - Main Parts(Impeller seal, shaft
PROGRAM)
COMPONENTS seal, surge capacitor, gaskets, hours
- New Serial Number & Nameplate
WSC/WDC
etc.), Bearings, Lube Parts
KEY BENEFITS
- Larger HMI display
CHILLER - HMI Kit
- Improved Data Layout
CONTROLS - MAJOR
Improved COMPONENTS
Control Technology - PCO5 Controllers 2004-2020
UPGRADE - User friendly (Unit & Compressors)
- Boosted reliability and compressor
protection.
VFD UPGRADE - Up to MAJOR
30% more COMPONENTS
energy efficiency - VFD Power Box Assembly 2001-2020
with a fixed-starter upgrade.
- 1 Year Parts Warranty.
- Enhance operational efficiency and - Inspections: Gate Rotor &
prolong equipment lifespan. Starter - 7-15 YO units
- Mitigate risk & potential for
AWS
CAP - 70-100 Parts: Oil filter, Oil - Or 35,000 run
catastrophic failures. change, Sensors &
2 YearMAJOR COMPONENTS hours
(CHILLER ASSURANCE
- P&L Warranty (If compressors Transducers, Fan Contactors,
PROGRAM) are replaced) Solenoid Valves, Flow Switch,
- New Serial Number & Nameplate & Relief Valves
- Increased unit performance visibility
Awv
EXTERNAL - Improved operator safety
- HMI Kit: Display, Window Kit, All AWV Units
HMI UPGRADE - Streamlined diagnostics
Window Film, HMI Cable
- Direct unit insight without reliance on
MAJOR COMPONENTS
BMS viewing
The term ‘New Added Parts' refers to components that are either being replaced or upgraded as part of the program offering .
2S Support Team Email:2SServiceSolutions@daikinapplied.com
Tim Bernard | Director of Service & System Solutions Vanessa Rivera | Program Manager Darren Goodwin | Technical Developer
Mobile: 612-615-3893 Mobile: 973-941-3471 Office: 770-334-3937
Email: Timothy.Bernard@daikinapplied.com Email: Vanessa.Rivera@daikinapplied.com Email: Darren.Goodwin@daikinapplied.com
7.6.24
ANALYZE YOUR BUILDING’S
ENERGY CONSUMPTION
WITH DAIKIN’S NEXT GENERATION OF ENERGY
MODELING SOFTWARE
When embarking on a ground-up project, planning a remodel, or considering a system
upgrade, every watt counts. Early access to actionable energy data is pivotal for unraveling
energy usage trends, selecting optimal HVAC equipment, and uncovering avenues for
cost reduction and potential rebates. This is why Daikin Applied has developed the next
generation of energy analysis and modeling software, EA Pro™ — which is backed by the
power of the Department of Energy’s EnergyPlus™ Simulation Engine.
By analyzing the synergistic effects of the building’s envelope, internal loads, and HVAC
characteristics, EA Pro™ can provide a customized model reflecting your project’s needs.
These models empower building owners and engineers with the insights they need to
transform energy consumption strategies and aid in equipment selection, leading to energy
and energy cost savings, as well as a reduction in the building’s carbon footprint.
NEXT-GENERATION APPROACH AND ENERGY ANALYSIS
THOROUGH EQUIPMENT AND BUILDING ANALYSIS
Models include the ability to analyze HVAC systems,
building envelope, lighting, controls, and process loads
EASY-TO-USE, CLOUD-BASED PLATFORM
Daikin’s EA Pro™ software boasts a user-friendly interface with
modern, intuitive output reports
LIFECYCLE COST ANALYSIS TOOL
Models feature the option to include initial costs, maintenance costs,
rebates, inflation rates, and escalation rates for lifecycle analysis
COMPREHENSIVE SUPPORT AND TRAINING
Daikin Applied will provide software training and maintenance
TAP INTO THE LEADING BUILDING ENERGY SIMULATION ENGINE
Models utilize the Department of Energy’s powerful
EnergyPlus™ simulation engine
LEARN MORE AT DAIKINAPPLIED.COM
© 2023 DAIKIN APPLIED | (800) 432.1342 | ASP31-555
THE FUTURE OF ENERGY ANALYSIS
ENERGY MODELING
FOR DAIKIN APPLIED EQUIPMENT
> REBEL® AND REBEL APPLIED™
• Dedicated outside air systems (DOAS)
• Heat pumps
> CHILLERS
• AWV and AWV with integrated free cooling
• WME with low condenser water temperature
• Heat recovery
• Waterside economizing for all chillers
> WATER SOURCE HEAT PUMPS
> AIR HANDLING UNITS
> CONDENSING UNITS
ENERGY MODELING
FOR DAIKIN NORTH AMERICA’S VRV
> SERIES
• Emerion
• Aurora™
• Water-cooled T-series
• Single-phase VRV
> DUCTED, NON-DUCTED AND MIXED UNITS
TM
LEARN MORE AT DAIKINAPPLIED.COM
© 2023 DAIKIN APPLIED | (800) 432.1342 | ASP31-554
THE FUTURE
OUROF ENERGY
APPROACHANALYSIS
SOLUTIONS FOR SOLUTIONS FOR
ECONOMIC ANALYSIS MODELING ALTERNATIVES
> ENERGYPLUS™ CALCULATIONS ACCEPTED BY > BUILDING ENVELOPE
UTILITIES AND REGULATORY AGENCIES
> LIGHTING
> CUSTOM OUTPUT REPORTS
> CONTROLS
• Appropriate for rebate purposes
> CHANGES IN VENTILATION
• For use by building owners
> HVAC EQUIPMENT
• Optimize chiller selection
• Compare new to existing equipment
• Evaluate different equipment options
3D Visual Representations of HVAC Equipment
Zone Equipment VRV Equipment
> Fan coil units > Outdoor units
> WSHPs • Air & water cooled
> VAV terminal units • Heat pump & heat recovery
> VRV ducted & non-ducted units > Ducted & non-ducted units
Plant Equipment Central Air Equipment
> Chillers (air & water cooled) > AHUs
> Boilers > Rooftop systems
> Cooling towers
LEARN MORE AT DAIKINAPPLIED.COM
© 2023 DAIKIN APPLIED | (800) 432.1342 | ASP31-554
OUR BRAND PROMISE
At Daikin, our goal is to make the time you
spend indoors as productive and pleasant as
possible, with superior comfort and quality air. We deliver extraordinary results for remarkable value. This means
Let us help you build convenience, confidence being ready for you whenever, wherever and however you need
and excellence into your buildings, and free us. Your Daikin Service team is on standby with well-outfitted
up your people to work toward your mission. local resources that are backed by the world’s number one air
Whether you need immediate service, routine conditioning company. Whether you’re looking to extend the
maintenance or an expert consultant, Daikin life of your equipment or to drive efficiency into every aspect of
is here to help. Daikin Service will make your business, our team will identify the solutions to meet you
your building the second best performing where you are today and take you where you want to go.
employee that props up everyone else.
REPLACEMENTS
BUILDING
MODERNIZE ASSESSMENTS
OPTIMIZE RENTALS
DAIKIN360 INTEGRATED SERVICE SOLUTIONS
We understand that your building is one of your company’s most significant investments, and a cornerstone of growth
and success. Our expertise in HVAC systems, delivered through Daikin360 Integrated Service Solutions, can help make
MAINTAIN
your building &
your second-best PARTS
employee by creating an ideal environment and quality air that propels & people and
your
REPAIR Plus, our advanced energy-saving solutions and protective maintenance plansSUPPLIES
customers forward. can help you control
your maintenance and operational costs. You can countANALYSIS
on Daikin Applied for advanced technology, agility and reliability.
Whenever, Wherever, However You Need Us.
REPLACEMENTS
BUILDING
MODERNIZE ASSESSMENTS
OPTIMIZE RENTALS
MAINTAIN & PARTS &
REPAIR SUPPLIES
Whenever,
LEARN MOREWherever, However
ABOUT DAIKIN360 You
SERVICE Need Us.
OFFERINGS
AT DAIKINAPPLIED.COM/360-SERVICE-SOLUTIONS
Service Program 1 – Centrifugal Chillers
Daikin Applied will perform the following procedures:
Annual Inspection
1. Test for refrigerant leaks including relief valve piping outlets
2. Check main starter and control panel
3. Inspect and tighten electrical connections
4. Check relays, operating, and safety controls
5. Check flow switch operation
6. Lubricate inlet vane linkage, if applicable
7. Check vane control setting and operation
8. Take and record water side pressure drops across vessels
9. Perform MicroTech check, log, and last fault analysis, and analyze performance.
10. Perform operating log if not MicroTech and analyze
11. Meg compressor and oil pump motors
12. Clean oil cooler strainer, water cooled only
13. Check oil sump heater operation
14. Perform oil analysis for wear metals, moisture, and acid
15. Inspect vibration eliminators and inspect water piping for leaks
16. Blow down condenser water strainer(s)
17. Check head pressure control operation for tower fans or bypass valve
18. Check minimum condenser water temperature operation
19. Clean purge drum and oil separator where applicable
20. Check oil in purge pump and oil separator where applicable
21. Lubricate purge pump motor where applicable
22. Visually inspect water side of condenser
Semi-Annual Inspection
1. Review manufacturer’s recommendations for operation
2. Check auxiliary equipment operation
3. Check oil levels
4. Check oil sump heater, gear case heater, and purge pump oil heaters where applicable
5. Check relays, operating, and safety controls
6. Check chilled water pump(s)
7. Check condenser water pump(s) and cooling tower
8. Check water chiller
9. Check purge unit operation where applicable
10. Log all operating conditions
11. Review operating procedures with chiller operator
Operational Inspection
1. Review owner’s log for trends
2. Inspect chiller for leaks
3. Inspect starter contacts for burns and discoloration
4. Run chiller and log readings, analyze performance
5. Record unusual noises and vibrations
6. Record refrigerant level in sightglass
7. Record oil level in sightglass
8. Verify operation of the oil heater and cooler
9. Check purge operation. Check sight glass and drain non-condensibles from purge drum where
applicable
10. Review chiller operation with chiller operator
First Year Maintenance
1. One Operational Inspection during the cooling season plus one inspection as detailed in items 2-
24
2. Test for refrigerant leaks including relief valve piping outlets
3. Check main starter and control panel
4. Inspect and tighten electrical connections
5. Check relays, operating, and safety controls
6. Check flow switch operation
7. Lubricate inlet vane linkage, if applicable
8. Check vane control setting and operation
9. Take and record water side pressure drops across vessels
10. Perform MicroTech check, log, and last fault analysis, and analyze performance.
11. Perform operating log if not MicroTech and analyze
12. Meg compressor and oil pump motors
13. Clean oil cooler strainer, water cooled only
14. Check oil sump heater operation
15. Perform oil analysis for wear metals, moisture, and acid
16. Inspect vibration eliminators and inspect water piping for leaks
17. Check condenser water strainer(s)
18. Check head pressure control operation for tower fans or bypass valve
19. Check minimum condenser water temperature operation.
20. Clean purge drum and oil separator where applicable
21. Check oil in purge and oil separator where applicable
22. Lubricate purge pump motor where applicable
23. Visually inspect water side of condenser
Head(s) to be removed by: ☐ Daikin Applied ☐ Customer
Cleand Condensers by: ☐ Daikin Applied ☐ Customer
Exceptions and additions
This service does not include “slide back” service on low pressure equipment.
Service Program 2 – Absorption Chillers
Daikin Applied will perform the following procedures:
Annual Inspection
1. Check starter and control panel
2. Confirm settings of motor overcurrent relay.
3. Inspect and tighten electrical connections
4. Check relays, operating, and safety controls
5. Check chilled-water flow switch operation
6. Check condenser-water flow switch operation
7. Inspect vibration eliminators and water piping for leaks
8. Check condenser water strainer(s)
9. Check solution/refrigerant pumps for abnormal noise
10. Check for steam leaks, NC units
11. Check operation of condensate float, NC units
12. Take solution sample for laboratory analysis
13. Take refrigerant-water sample for laboratory analysis
14. Check purge operation
15. Change purge pump oil
16. Lubricate purge pump motor and check belt tension
17. Clean magnetic strainer on the solution motor cooling circuits, if applicable
Burner Assembly (if applicable)
Annual Inspection
1. Lubricate motors
2. Inspect combustion
3. Inspect all valves
4. Remove pilot assembly and inspect ignition electrodes
5. Inspect operation and limit controls
6. Check and tighten all electrical connections
7. Check tightness of linkage
8. Check flame motor for signal strength
9. Check all fuel pressures
10. Check O2, CO2, and smoke spot levels
Seasonal Startup
1. Review manufacturer’s recommendations for startup
2. Check auxiliary equipment operation
3. Check and test all operating and safety controls
4. Start chilled water pump(s)
5. Start condenser water pump(s) and cooling tower
6. Start absorber
7. Check solution-pump motor operation
8. Log operating conditions after unit stabilizes
9. Add octyl alcohol, if required
10. Trim solution concentration for maximum efficiency
11. Take solution sample for laboratory analysis
12. Check purge unit operation
13. Review operating procedures with chiller operator
Operational Inspection
1. Review owner’s log for trends
2. Log all operating conditions
3. Complete Periodic Inspection Data Sheet
4. Check function of chilled water flow switch
5. Check accuracy of high-temperature generator-pressure gauge
6. Check function of generator solution-level electrodes
7. Check solution/refrigerant pumps for abnormal noise
8. Check steam valve actuation on NC units
9. Confirm settings of motor overcurrent relays
10. Check and test all operating and safety controls
11. Check purge operation and belt
12. Review chiller operation with chiller operator
First Year Maintenance
1. One Operational Inspection during the cooling season plus one inspection as detailed in items 2-
23
2. Check starter and control panel
3. Confirm settings of motor overcurrent relays
4. Inspect and tighten electrical connections
5. Check relays, operating, and safety controls
6. Check chilled-water flow-switch operation
7. Check condenser water flow switch operation
8. Retorque rupture-disk flange
9. Inspect vibration eliminators and water piping for leaks
10. Check condenser water strainer(s)
11. Check solution/refrigerant pumps for abnormal noise
12. Check for steam leaks, NC units
13. Check operation of condensate float, NC units
14. Take solution sample for laboratory analysis
15. Take refrigerant-water sample for laboratory analysis
16. Take TRG reading, if applicable
17. Check purge operation
18. Change purge pump oil
19. Lubricate purge-pump motor and check belt tension
20. Clean magnetic strainer on solution-motor cooling circuits, if applicable
21. Complete Periodic Inspection Data Sheet
22. Manually clean absorber and condenser tubes
Head(s) to be removed by: ☐ Daikin Applied ☐ Customer
Exceptions/Clarifications
None
Service Program 3 – Reciprocating/Scroll Chillers
Daikin Applied will perform the following procedures:
Annual Inspection
1. Inspect for leaks
2. Check belts, sheaves, and coupling alignment where applicable, and adjust as required
3. Check compressor oil level, acid test oil and meg hermetic motor
4. Check compressor crankcase heater operation
5. Check vibration eliminators
6. Inspect electrical connections, contactors, relays, and operating/safety controls
Seasonal Startup
1. Review manufacturer’s recommendations for startu.
2. Check auxiliary equipment operation
3. Energize crankcase heater per manufacturer’s recommendation for crankcase warm-up
4. Check and test all operating and safety controls
5. Start chilled water pump, condenser water pump, and cooling tower
6. Start water chiller
7. Check refrigerant charge, oil level, and oil pressure
8. Log all operating conditions after unit stabilizes
9. Review operating procedures and owner’s log with chiller operator
Operational Inspection
1. Review owner’s log and log all operating conditions
2. Inspect chiller and make adjustments as required
3. Cycle operating controls and check unloaders
4. Review chiller operation with chiller operator
Exceptions/Clarifications
None
Service Program 4 – Condensing Units
Daikin Applied will perform the following procedures:
Air Cooled - Startup Inspection
1. Review manufacturer’s recommendations for startup
2. Energize crankcase heater per manufacturer’s recommendation
3. Remove all debris from within and around unit
4. Inspect for leaks
5. Check belts, pulleys, and mounts and adjust as required
6. Lubricate fan and motor bearings per manufacturer’s recommendation
7. Inspect electrical connections, contactors and relays
8. Check motor operating conditions
9. Check and clean fan blades as required
10. Check coil
11. Check vibration eliminators where applicable
12. Check compressor oil level, acid test oil and meg hermetic motor(s) 20 HP and above
13. Check and test all operating and safety controls
14. Check operating conditions and adjust as required
Operational Inspection
1. Inspect for leaks
2. Lubricate fan bearings per manufacturer’s recommendation
3. Lubricate motor bearings per manufacturer’s recommendation
4. Check belts and sheaves and adjust as required
5. Check operating conditions and adjust as required
Water Cooled - Startup Inspection
1. Review manufacturer’s recommendation for startup
2. Energize crankcase heater per manufacturer’s recommendation
3. Inspect for leaks
4. Vent condenser water system of trapped air
5. Inspect electrical connections, contactors, relays and operating/safety controls
6. Check vibration eliminators
7. Check compressor oil level, acid test oil, and meg hermetic motor(s) 20 HP and above
8. Check and test all operating and safety controls
9. Check operating conditions and adjust as required
Operational Inspection
1. Inspect for leaks
2. Check operating conditions and adjust as required
Exceptions/Clarifications
None
Service Program 5 – Fan and Central Fan Systems
Daikin Applied will perform the following procedures:
Fans - Inspection
1. Check and clean fan assembly
2. Lubricate fan bearings per manufacturer’s recommendations
3. Lubricate motor bearings per manufacturer’s recommendations
4. Check belts and sheaves
5. Tighten all nuts and bolts
6. Check motor mounts and vibration pads
7. Check motor operating conditions
8. Inspect electrical connections and contactors
9. Lubricate and adjust associated dampers and linkage
10. Check fan operation
Central Fan Systems - Inspection
1. Lubricate fan bearings per manufacturer’s recommendations
2. Lubricate motor bearings per manufacturer’s recommendations
3. Check belts and sheaves
4. Tighten all nuts and bolts
5. Check motor mounts and vibration pads
6. Check motor operating conditions
7. Inspect electrical connections and contactors
8. Lubricate and adjust associated dampers and linkage
9. Check fan operation
10. Check strainers, check steam traps, and hand valves
11. Check filter-advancing mechanism and lubricate and adjust as required
12. Inspect filters
13. Check heating and cooling coils
14. Inspect humidifier
Exceptions/Clarifications
None
Service Program 6 – Cooling Towers and Evaporative Condensers
Daikin Applied will perform the following procedures:
Annual Inspection
1. Remove all debris from within and around unit and flush as required
2. Check and blow down strainers, bleed, overflow, and drain
3. Lubricate fan and motor bearings per manufacturer’s recommendation
4. Check oil in gear reducer assembly as per manufacturer’s recommendation
5. Check belts, motor pulley, and motor mounts and adjust as required
6. Inspect electrical connections, contactors, relays, and operating/safety controls
7. Check motor operating conditions
8. Clean float valve assembly and check for proper operation
9. Structural components and fill are not included in agreement
Operational Inspection
1. Inspect fan, motor and belts
2. Check oil level in gear reducer and add oil as required
3. Check intake strainer, bleed, and overflow
4. Check operating conditions and adjust as required
Exceptions/Clarifications:
Mechanical moving parts coverage only
Service Program 7 – Pumps
Daikin Applied will perform the following procedures:
Inspection
1. Lubricate pump bearings per manufacturer’s recommendations
2. Lubricate motor bearings per manufacturer’s recommendations
3. Tighten all nuts and bolts; check motor mounts and vibration pads
4. Visually check-pump alignment and coupling
5. Check motor operating conditions
6. Inspect electrical connections and contactors
7. Check and blow down condenser-pump strainers and check hand valves
8. Inspect mechanical seals or inspect pump packing
9. Verify gauges for accuracy
Exceptions/Clarifications
Mechanical moving parts coverage only
Service Program 8 – Terminal Units
Daikin Applied will perform the following procedures:
Unit Ventilator Inspection
1. Brush and vacuum grills, coil, fan and unit 5. Check and clean strainers; check steam
interior traps and hand valves
2. Lubricate fan motor bearings per 6. Inspect filters
manufacturer’s recommendations 7. Check unit operating conditions.
3. Check belts and sheaves and adjust as 8. Lubricate and adjust dampers and linkage.
required
4. Check and clean drains and drain pan
Unit Heaters Inspection
1. Brush and vacuum coil, fan, and housing as 4. Check and clean strainers; check steam
require traps and hand valves
2. Lubricate fan and motor bearings per 5. Inspect electrical connections, contactors,
manufacturer’s recommendations relays and operating/safety controls
3. Check belt and sheaves and adjust as 6. Check unit operation and adjust as required
required
Fan Coils Inspection
1. Brush and vacuum coil, grills, fan, and unit 4. Check and clean drains and drain pans
interior 5. Check and clean strainers; check steam
2. Lubricate fan and motor bearings per traps and hand valves
manufacturer’s recommendation 6. Check unit operating conditions
3. Check belt and sheaves and adjust as
required
Radiation Inspection
1. Visually inspect fins/cast iron and clean as
required
2. Check and clean strainers; check steam
traps and hand valves
Induction Units Inspection
1. Visually inspect coil and clean as required
2. Check and clean drains and drain pans
3. Clean discharge grill
4. Check and clean strainers; check steam
traps and hand valves
Reheat Coils Inspection
1. Visually inspect coil and clean as required
2. Check and clean strainers. Check steam
traps and hand valves
3. Inspect electrical connections, relays,
contactors, and operating and safety
controls (electric coils only).
Boxes - Dual Duct and Variable Air Volume
Inspection
1. Inspect box for duct work connection
2. Lubricate and adjust dampers and linkage
Exceptions/Clarification: None
Service Program 9 – Automatic Temperature Controls
Daikin Applied will perform the following procedures:
Air Compressor
1. Drain tank and check traps 6. Check high-pressure safety valve
2. Change oil and check oil pressures 7. Check motor operating conditions and lubricate
3. Check belts and sheave. 8. Check PE switch, starter and alternator
4. Check suction filter 9. Record compressor run time
5. Check unloader and check valve
Refrigerated Air Dryer
1. Check refrigerant pressure (33#). 4. Check drain tap and bypass valves
2. Check refrigerant temperature (35°)
3. Check condenser and cover grills
Filter and Pressure Reducing Station
1. Check particle filters 3. Check pressure-reducing valve settings
2. Check oil filter 4. Check low-pressure safety switch
Time Clocks
1. Check operation and settings
2. Check solenoid-air valve and clock-bypass
switch
Boiler, Chiller, Convertor, Pumps, and Zone Control
1. Calibrate all controllers 4. Check all control valves
2. Calibrate all transmitter and receiver 5. Check all pilot positioners
gauges 6. Check all auxiliary control devices
3. Check all PE switches
Fan Systems and HVAC Unit Controls
1. Check all dampers and lubricate 5. Calibrate all transmitters and receiver gauges
2. Check all pilot positioners 6. Check all solenoid air valves, PE switches, and
3. Check all control valves air valves
4. Calibrate all controllers 7. Check all auxiliary control devices
8. Clean/wipe down panel face
Annual Inspection - Heating Only, Cooling Only or Heating and Cooling Room/Terminal Unit Controls
1. Check all room stats
2. Check all control valves
3. Check operation of unit-coil steam traps
Exceptions/Clarifications:
None
Service Program 10 – Miscellaneous HVAC Equipment
Daikin Applied will perform the following procedures:
Heat Exchanger Inspection
1. Check for leaks and tighten connections
2. Verify pressure gauge and thermometer accuracy
3. Check and clean strainers; check steam traps and hand valves
4. Check operating safety devices
Humidifiers Inspection
1. Check and clean strainers; check steam trap and hand valves
2. Clean and check float assembly.
3. Check and clean drains and drain pan
4. Clean heating element
5. Inspect electrical connections, relays, contactors, and operating/safety controls
6. Clean plugged spray nozzles
7. Check unit operating conditions
Steam PRV Inspection
1. Verify accuracy of gauges
2. Check unit operation
Exceptions/Clarifications
None
Service Program 11 – Unitary Heating Equipment Only
Daikin Applied will perform the following procedures:
Annual Inspection
1. Lubricate fan bearings per manufacturer’s recommendation
2. Lubricate motor bearings per manufacturer’s recommendation
3. Check belts and sheaves and adjust as required
4. Lubricate and adjust dampers and linkage
5. Inspect filters
6. Check motor operating conditions
7. Inspect electrical connections, contactors, relays and operating safety controls
8. Check and clean strainers and humidifier; check hand valves and steam traps
9. Visually inspect coil and clean as required
10. Check and clean drains and drain pans
11. Inspect, clean, and lubricate the burner and combustion-control equipment (gas or oil burner only)
12. Check burner sequence of operation and combustion air equipment (gas and oil burner only)
Operational Inspection
1. Lubricate fan bearings per manufacturer’s recommendation
2. Lubricate motor bearings per manufacturer’s recommendation
3. Check belts and sheaves and adjust as required
4. Inspect filters
5. Check unit operation and make adjustments as required
Exceptions/Clarifications
None
Service Program 12 – Unitary Cooling Equipment Only
Daikin Applied will perform the following procedures:
Annual Inspection
1. Lubricate fan bearings per manufacturer’s recommendation
2. Lubricate motor bearings per manufacturer’s recommendation
3. Check belts and sheaves and adjust as required
4. Check coils
5. Check and clean drain pan and drains
6. Lubricate and adjust dampers and linkages
7. Inspect filters
8. Check motor operating conditions
9. Inspect electrical connections, contactors, relays, and operating/safety control.
10. Check compressor oil level, acid test oil, and meg motor(s) 20 HP and above; check crankcase
heater operation (DX only)
11. Start compressor, check operating conditions, and adjust as required (DX only)
Operational Inspection
1. Lubricate fan bearings per manufacturer’s recommendation
2. Lubricate motor bearings per manufacturer’s recommendation
3. Check belts and sheaves and adjust as required
4. Inspect filters
5. Check coils
6. Inspect for refrigerant leaks
7. Check operating conditions and adjust as required
Exceptions/Clarifications
None
Service Program 13 – Unitary Heating & Cooling Equipment
Daikin Applied will perform the following procedures:
Annual Inspection - Heating
1. Lubricate fan bearings per manufacturer’s 7. Inspect electrical connections, contactors,
recommendation relays, and operating safety controls
2. Lubricate motor bearings per 8. Check and clean strainers and humidifier;
manufacturer’s recommendation check hand valves and steam traps
3. Check belts and sheaves and adjust as 9. Check and clean drains and drain pans
required 10. Inspect, clean, and lubricate the burner and
4. Lubricate and adjust dampers and linkage combustion control equipment
5. Inspect filters 11. Check burner sequence of operation and
6. Check motor operating conditions combustion air equipment
Operational Inspection
1. Lubricate fan bearings per manufacturer’s 3. Check belts and sheaves and adjust as
recommendation required
2. Lubricate motor bearings per 4. Inspect filters
manufacturer’s recommendation 5. Check unit operation and make adjustments as
required
Annual Inspection - Cooling
1. Lubricate fan bearings per manufacturer’s 8. Check motor operating conditions
recommendation 9. Inspect electrical connections, contactors,
2. Lubricate motor bearings per relays, and operating/safety controls
manufacturer’s recommendation
10. Check compressor oil level, acid test oil, and
3. Check belts and sheaves and adjust as
required meg motor(s) 20 HP and above; check
4. Check coils crankcase heater operation (DX only)
5. Lubricate and adjust dampers and linkages 11. Start compressor, check operating conditions,
6. Check and clean drain pan and drains and adjust as required (DX only)
7. Inspect filters
Operational Inspection
1. Lubricate fan bearings per manufacturer’s 4. Inspect filters
recommendation 5. Check coils
2. Lubricate motor bearings per 6. Visually inspect for refrigerant leaks
manufacturer’s recommendation 7. Check operating conditions and adjust as
3. Check belt and sheaves and adjust as required
required
Exceptions/Clarifications:
None
Service Program 14 – Steam Boilers
Daikin Applied will perform the following procedures:
Annual Inspection
1. Inspect fireside of boiler and record condition
2. Brush and vacuum soot and dirt from flues and combustion chamber
3. Inspect firebrick and refractory for defects
4. Visually inspect boiler pressure vessel for possible leaks and record condition
5. Drain and flush water side of boiler to remove loose scales and sludge and record condition
6. Disassemble, inspect, and clean low-water cutoff
7. Check hand valves and automatic feed equipment and adjust as required
8. Inspect, clean, and lubricate the burner and combustion control equipment
9. Reassemble and fill boiler and fire burner to boil off oxygen
10. Check burner sequence of operation and combustion-air equipment
11. Check fuel piping for leaks and proper support
Seasonal Startup
1. Review manufacturer’s recommendations for boiler and burner startup
2. Check fuel supply
3. Check auxiliary equipment operation
4. Inspect burner, boiler and controls prior to startup
5. Start burner, check operating controls, test safety controls and pressure-relief valve
6. Perform combustion tests and adjust burner for maximum efficiency
7. Log all operating conditions
8. Review operating procedures and owner’s log with boiler operator
Operational Inspection
1. Review owner’s log and log all operating conditions
2. Inspect boiler and burner and make adjustments as required
3. Test low-water cut-off and pressure-relief valve
4. Check operating and safety controls
5. Review boiler operation with boiler operator
Seasonal Shut Down
1. Review owner’s log and log all operating conditions
2. Shut off burner and open electrical disconnect
3. Close fuel supply valves
4. Thoroughly blow down boiler
5. Review boiler operation with boiler operator
Exceptions/Clarifications
None
Service Program 15 – Hot Water Boilers
Daikin Applied will perform the following procedures:
Annual Inspection
1. Inspect fireside of boiler and record condition
2. Brush and vacuum soot and dirt from flues and combustion chamber
3. Inspect firebrick and refractory for defects
4. Visually inspect boiler pressure vessel for possible leaks and record condition
5. Disassemble, inspect, and clean low-water cutoff
6. Check hand valves and automatic feed equipment and adjust as required
7. Inspect, clean, and lubricate the burner and combustion control equipment
8. Reassemble boiler
9. Check burner sequence of operation and combustion air equipment
10. Check fuel piping for leaks and proper support
Seasonal Startup
1. Review manufacturer’s recommendations for boiler and burner startup
2. Check fuel supply
3. Check auxiliary equipment operation
4. Inspect burner, boiler, and controls prior to startup
5. Start burner, check operating controls, and test safety controls and pressure-relief valve
6. Perform combustion tests and adjust burner for maximum efficiency
7. Log all operating conditions
8. Review operating procedures and owner’s log with boiler operator
Operational Inspection
1. Review owner’s log and log all operating conditions
2. Inspect boiler and burner and make adjustments as required
3. Test low-water cut-off and pressure-relief valve
4. Check operating and safety controls
5. Review boiler operation with boiler operator
Seasonal Shut Down
1. Review owner’s log. Log all operating conditions
2. Shut off burner and open electrical disconnect
3. Close fuel supply valves
4. Review boiler operation with boiler operator
Exceptions/Clarifications
None
Service Program 16 – Predictive Maintenance
Daikin Applied will perform the following procedures:
Spectrochemical Oil Analysis: 0 Oil Analysis(es) will be performed annually
Parameters Tested Results
Metals Diagnosis
Moisture Trends
Acid Number Recommendations
Refrigerant Analysis: 0 Refrigerant Analysis(es) will be performed annually
Parameters Tested Results
High Boiling Residue Diagnosis
Acid Number Trends
Moisture Content Recommendations
Eddy Current Tube Analysis: 0 Eddy Current Analysis(es) will be performed annually
Or is available on a quoted basis
Parameters Tested Results
Corrosion Verbal Report
Support Water Written Report
Freeze Bulges Charts/Diagrams
Split Fins Recommendations
Leakers
Pitting
Vibration Analysis: 0 Vibration Analysis(es) will be performed annually
Parameters Tested Results
Measure Horizontal Deflections Report
Measure Vertical Deflections Trends
Measures Axial Deflections Recommendations
Establish Baseline
Lithium Bromide Analysis: 0 Lithium Bromide Analysis(es) will be performed annually
Parameters Tested Results
Metals Diagnosis
Lithium Bromide % Trends
Lithium Hydroxide Recommendations
Inhibitor Chemical Additions
Ammonia %
Alcohol Additive
Foaming Test
Foreign Contamination
Refrigerant Water Analysis: 0 Refrigerant Water Analysis(es) will be performed annually
Parameters Tested Results
Lithium Bromide Content Diagnosis
Alkalinity Trends
Inhibitor By-Product Recommendations
N Factor
Glycol Analysis: 0 Glycol Analysis(es) will be performed annually
Parameters Tested Results
Color Diagnosis
Glycol Content Trends
Freezing Point Recommendations
Suspended Solids
Reserve Alkalinity
Acid Number
Flue Gas Analysis: 0 Flue Gas Analysis(es) will be performed annually
Parameters Tested Results
CO2 Content Diagnosis
O2 Content Trends
Stack Temperature Recommendations
Exceptions
None
Service Program 17 – Vane Axial Fans
Daikin Applied will perform the following procedures:
Inspection
1. Inspect inlet bells and screens, discharge flanges, fan supports, and braces for defects
2. Remove, clean, and inspect all rotor blades for wear (blade removal not required on Joy fans)
3. Inspect thrust bearing on each blade
4. Remove spider or hub and clean
5. Reassemble fan rotor and torque properly
6. Check blade pitch
7. Inspect linkages for proper operation and defects
8. Check motor mounting bolts - torque per specification
9. Verify correct lubricants recommended by manufacturer
10. Install grease zerts where applicable
11. Clean grease inlet areas to prevent grease contamination
12. Lubricate motor bearings
13. Grease blade shaft bearings
14. Grease spider hub sliding joint; joy fans - open pressure relief ports
15. Lubricate blade links and inspect for binding
16. Lubricate pillow block bearing where applicable
17. Check starter contacts
18. Check all electrical connections for looseness and overheating
19. Check voltages on all phases of starter and record values
20. Check motor amps on each phase for balance and correctness at full pitch and record values
21. Meg motor windings and record values
22. Check for air leaks
23. Check control air and actuator air pressures
24. Calibrate pitch controller and verify there is no hunting
25. Check time delay on start-up
26. Perform electronic-vibration analysis of both axes (this does not include cost of extensive
balancing)
Exceptions/Clarifications
None
Service Program 19 – Inspection and Conversion
Daikin Applied will perform the following procedures:
Leak Testing/Repair
1. Test chiller and related equipment for refrigerant leakage
2. Identify and locate leaks
3. Recommend corrective procedures
4. Repair leaks if equipment covered under a comprehensive agreement
Recover/Retain/Recycle
1. Recover and recycle refrigerant from chiller as necessary
2. Identify type(s) of refrigerant and amount(s) recycled
3. Replenish refrigerant in chiller as needed, if inspected and leaks repaired
4. Identify type(s) of refrigerant and amount(s) required
5. Reclaim refrigerant from equipment
6. Identify type(s) and amount(s) of refrigerant reclaimed
7. Verify date(s) tested, distillation vendor, and date(s) shipped and returned
Disposal
1. Dispose of refrigerant
2. Identify type(s) and amount(s) of disposed refrigerant
3. Verify date(s) tested, disposal vendor, and date(s) shipped
4. Obtain necessary federal, state, and local authorization for transport and disposal of refrigerant.
Refrigerant Coverage by: ☐ Daikin Applied ☐ Customer
Exceptions/Clarifications
Refrigerant coverage – R134a – 100%
R-11, R-12, R-500 – (CFC) – not covered under this agreement
R-22 – 100 percent
Service Program 20 – Screw Chillers
Daikin Applied will perform the following procedures:
Annual Inspection
1. Inspect for refrigerant and oil leaks
2. Inspect vibration eliminators and water piping for leaks
3. Check freeze protection, evaporator, and piping heaters, glycol content
4. Check and blow down water piping strainers
5. Check refrigerant in sightglass
6. Check compressor-oil presence in sightglass, if applicable
7. Inspect and tighten electrical connections
8. Check relays and operating/safety controls
9. Check crankcase heater operation
10. Meg hermetic motor
11. Check operation of electronic expansion valve
12. Perform MicroTech check, log, and last fault analysis, and analyze performance
13. Check condenser coils, clean debris from around condenser, Model ALS/AGS air cooled units
14. Check condenser fan operation, Model ALS air-cooled units
15. Check condenser water flow, Model PFS water-cooled units
Operating Inspection
1. Inspect for refrigerant and oil leaks
2. Inspect vibration eliminators and inspect water piping for leaks
3. Check and blow down water piping strainers
4. Check refrigerant in sightglass
5. Check compressor oil presence in sightglass, if applicable
6. Inspect and tighten electrical connections
7. Check relays and operating/safety controls
8. Check crankcase heater operation
9. Perform MicroTech check, log, and last fault analysis, and analyze performance
10. Check condenser coils, clean debris from around condenser, Model ALS air-cooled units
11. Check condenser water flow, Model PFS water-cooled units
12. Take and record water side pressure drops across vessels
First Year Maintenance
1. One operational inspection during the cooling season plus one inspection as detailed in items 2-16
2. Inspect for refrigerant and oil leaks
3. Inspect vibration eliminators and water piping for leaks
4. Check freeze protection, evaporator, and piping heaters, glycol content
5. Check and blow down water piping strainers
6. Check refrigerant in sightglass
7. Check compressor oil presence in sightglass, if applicable
8. Inspect and tighten electrical connections
9. Check relays and operating/safety controls
10. Check crankcase heater operation
11. Meg hermetic motor
12. Check operation of electronic expansion valve
13. Perform MicroTech check, log, and last fault analysis, and analysis performance
14. Check and clean condenser coils, Model ALS air-cooled units
15. Check and clean condenser fans, Model ALS air-cooled units
16. Manually clean water side of condenser, Model PFS water cooled units
Head(s) to be removed by: ☐ Daikin Applied ☐ Customer
Exceptions/Clarifications
None
Service Program 21 – Magnetic Bearing Chillers
Daikin Applied will perform the following procedures:
Annual Inspection
1. Test for refrigerant leaks including relief valve piping outlets
2. Inspect and tighten electrical connections in power panels and control panel
3. Apply dielectric grease to applicable terminals
4. Measure and record main supply voltages
5. Measure and record magnetic bearings coil resistance if applicable
6. Check relays, operating, and safety controls
7. Check flow switch operation
8. Check vane control operation
9. Check Electronic Expansion Valve operation
10. Perform MicroTech II or MicroTech E check, log, and last fault analysis, analyze performance
11. Measure and record water side pressure drops across vessels and compare to design
12. Inspect vibration eliminators and inspect water piping for leaks at chiller and cooling tower
13. Clean (flush) condenser water strainer(s)
14. Check minimum and normal temperature or lift control operation for tower fans and bypass valve
15. Clean external surfaces (painting external surfaces for Comprehensive Maintenance Agreements
as determined necessary by Daikin Applied)
16. Log operating conditions
17. Review operating procedures with chiller operator.
18. Optional Tube services included:
☐ Manually brush water side of condenser tubes
☐ Chemical clean water side of condenser tubes
☐ Manually brush water side of evaporator tubes
☐ Chemical clean water side of evaporator tubes
☐ Head(s) to be removed by: ☐ Daikin Applied ☐ Customer
Operating Inspection
1. Review owner’s log for trends
2. Inspect chiller for leaks
3. Check relays, operating, and safety controls settings
4. Inspect power panels and control panel
5. Measure and record main supply voltages
6. Perform MicroTech II or MicroTech E check, log, and last fault analysis
7. Review compressor event and fault logs
8. Record unusual noises and vibrations
9. Log operating conditions
10. Review chiller (s) operation with the operator
Exceptions/Clarifications:
Brush clean condenser tubes to be performed by Daikin Applied
Service Program 24 – D-Net Performance Services
Daikin Applied will perform the following procedures:
Plan options for D-Net™ Remote Services
__ Wired (LAN connection)*
__ Wireless (modem connection)
* Requires customer supplied internet connection (two way communication).
Inspections
During normal working hours Daikin Applied shall provide ___ on-site inspections for all equipment listed
on the Equipment Schedule on page 3 and ___ remote inspections for all D-Net communicating
equipment listed in Table 1 below, unless otherwise noted.
1. Daikin Applied agrees to:
a) For all agreements that include D-Net Remote Services (Remote Monitoring and/or Performance
Monitoring), Daikin Applied also agrees to:
b) Advise the owner in writing of the D-Net remote communications hardware (D-Net Performance
Services Communication Hardware List, Table 2), to be installed and the location thereof.
c) Utilize the D-Net remote communications capabilities to facilitate the speed and efficiency of
providing the services described herein for the equipment indicated as “D-Net included”. Remote
communications access may include but not be limited to: view equipment operating parameters,
receive alarms, harvest operating data, and recommend and/or perform service operations that
can be done via remote communications.
d) Remove and recover D-Net hardware that was installed in order to enable D-Net Remote
Services and remains the property of Daikin Applied within 30 days of any written cancellation of
this agreement.
2. Customer agrees to:
a) For all agreements that include D-Net Remote Services, Customer also agrees to:
b) Allow Daikin Applied to link all equipment as noted herein to be remotely serviced or monitored
and install and commission D-Net hardware to enable Internet communications to the equipment.
All communications equipment provided by Daikin Applied including Applied Local Control panels,
routers, modems, and/or Advanced Web Modules shall be labeled “Property of Daikin Applied”
and shall remain the property of Daikin Applied.
c) Allow Daikin Applied to utilize D-Net remote support capabilities to address operational issues,
reset alarms, and/or modify a unit’s operating parameters to the extent appropriate for remote
support for maintenance and repair.
d) Should Internet communications be lost, allow Daikin Applied access to above communications
equipment in a timely manner during normal working hours.
e) Allow Daikin Applied to access the site within 30 days of any written cancellation of this
agreement to remove and recover D-Net hardware that was installed in order to enable D-Net
Remote Services and remains the property of Daikin Applied.
f) Customer agrees that all requests for service must be requested through established means.
Daikin Applied will not initiate a service call or respond on-site or via remote D-Net capabilities
without appropriate customer communication. However, Daikin Applied may notify the customer
of an alarm/issue that the customer may not yet be aware and request if a remote or on-site
response is desired.
Customer Acceptance:
Accept: I agree to Daikin Applied’s Terms and Conditions for D-Net Performance Services
support as described herein.
Conditional Acceptance: I agree to accept Daikin Applied’s D-Net Performance Services with the
condition that any repairs to operational issues, resetting of alarms, and/or modifying of unit operating
parameters are done on-site, not remotely. I understand that this may limit Daikin Applied’s ability to
respond and resolve issues quickly.
Table 1: D-Net Performance Services Equipment Schedule
D-Net Hardware (Model/SN) Location Installed Date Installed Date Removed
Table 2: D-Net Performance Services Communication Hardware List
D-Net Hardware (Model/SN) Location Installed Date Installed Date Removed
Exceptions/Clarifications
None
Contingency Planning
Are you prepared for operational
disruptions to your HVAC system?
Make sure you are ready when the unexpected happens
From natural disasters to everyday mechanical failures, all facilities face some level Plan Layout
of risk due to loss of cooling in their facilities. A failure could result in anything from
minor discomfort due to lack of temperature control to losing hundreds of thousands Finincial risk analysis
of dollars due to lost productivity. Knowing what you have at risk can help you decide
Risk assesment
the level of planning that is warranted.
Many companies work diligently to make sure their facilities have proper evacuation Equipment identification
and safety plans. However, few think about what it will take to get the facility back
Prioritization
up and running if something were to happen to their mechanical systems.
Let us develop a Contingency Plan for you. We will walk you through the steps System connection
to determine the financial risks associated with losing control of your indoor
environment. When it comes to emergencies, we all understand the importance of
Power availability
having a plan and practicing it. These practices help us react quickly during stressful Electrical connection
times and are designed to help protect your most valuable assets.
Temporary equipment
location
Plan creation
Implement and review
©2015 Daikin Applied. All Rights Reserved.
Solutions from people & ideas you can trust.
Program benefits want to consider load prioritization and/or load shedding to
With a contingency plan, you gain control and peace of mind reduce the amount of capacity required. For a short period of
knowing that your facility is prepared to operate through time, you may be able to operate with higher air temperatures
any disaster and be back up and running quickly. Disruptions in certain areas and completely shut down others.
can occur at any time. Having a plan and being prepared in Step 5 – System connection
advance can reduce the risk of financial loss by: How and where connections are made helps reduce time and
• Shortening the time needed to acquire, install and money. Care will be taken to choose a location that is easily
start up HVAC equipment. In addition, having the accessible and that requires the least amount of temporary
paperwork completed in advance further reduces installation material to keep additional costs to a minimum.
delivery time. Step 6 – Power availability
• Ensuring that all parties involved in dealing with the The need to document the available voltage(s) and amperage is
outage are aware of their roles and are trained in vital because a transformer or generator may be required. Even
the processes and actions needed to deal with the if your power has not been affected, some temporary units may
problem. require more power than your existing equipment uses.
• Lowering the total cost of the temporary solutions Step 7 – Electrical connection
because any necessary building modifications can Whether existing electrical service is adequate or new electrical
be scheduled, instead of being performed under service will be installed, we will establish the location of the
emergency conditions. temporary electrical connection(s) and how they will be made.
• Reducing startup delays caused by oversights or
problems resulting from improvised designs. Step 8 – Temporary equipment location
• Improving a facility’s operations by identifying critical Equipment location is important for determining how much
infrastructure that must be maintained. electrical cable, and chilled water hose will be required. We
will also consider safety of the public and personnel, security,
Laying out your Plan ease of placement, equipment clearances, structural loads,
Step 1 – Financial risk analysis ground firmness and level, noise, public visibility, auto and
The contingency process begins with a review of the different pedestrian traffic, permits, and many other things to minimize
functional areas of your facility, their dependence on power, the impact on normal operations.
HVAC equipment, and the impact a loss could potentially Step 9 – Plan creation
have. By understanding the importance of these items to your Your Daikin Representative will provide your organization
operations and quantifying their financial impact, we can with a plan proposal. Included in the proposal are the
determine the areas that need to be considered. recommended temporary equipment solutions, the total
Step 2 – Risk assessment investment required (both capital and expense), budgetary
We will identify the potential causes for an interruption and figures for the temporary solutions (including first and
rank them based on cost impact, probability of occurrence and recurring costs), and detailed roles and responsibilities for
system downtime. internal and external resources.
Step 3 – Equipment identification Step 10 – Implement and review
Your Daikin Applied Represenative will work with you to To help expedite the ordering and delivery of a temporary
document all equipment in your HVAC and power systems, system, in an emergency situation, it is important to make
including their operating conditions. This process may uncover sure that all documents, such as purchase orders and rental
system weaknesses that need to be addressed prior to agreements, are completed, and all recommended building
implementation of the plan. modifications are made. We also recommend that the
plan be reviewed at least once a year, or when any facility
Step 4 – Prioritization changes are made.
We will evaluate your most critical facility loads and process
needs for essential operations, including those with the highest
financial implications for your business. At this point, you may
For more information about our complete line of Parts and Service, contact your local Daikin
Applied Service or visit www.DaikinApplied.com to find an office near you.
GS-07F-0377V ©2015 Daikin Applied | (800) 432-1342 | www.DaikinApplied.com | ASP 31-408
Contingency Planning for
Schools
You have enough to deal with when things
are going right.
“The Plan”
Having a contingency plan is more than making a list of the equipment that you
Plan Layout
need to rent until your system is able to get back on line. It is preparing your facility Finincial risk analysis
to be rental-ready. Identifying the risks and making certain that the appropriate
connections are in place so temporary cooling can be connected quickly, this is Risk assesment
essential to having a complete contingency plan.
Equipment identification
Daikin Rental Solutions has created a program that helps educational institutions
develop contingency plans for their critical HVAC systems. This entails an evaluation Prioritization
of the school’s cooling and power systems to identify potential sources of failure. The
System connection
next step is developing a blueprint to show where the connections are made, where
the equipment goes, and how to get it there. Power availability
If temporary cooling equipment is required, the plan can be commissioned at a
moment’s notice. The goal is to minimize downtime and reduce the risk of financial
Electrical connection
loss and educational services disruption due to a loss of your facility’s HVAC system. Temporary equipment
location
Plan creation
Implement and review
©2015 Daikin Applied. All Rights Reserved.
Solutions from people & ideas you can trust.
Knowing your risk Services beyond rental
Many aspects of facility management can be handled Daikin Applied, as part of the #1 global air conditioning
proactively through proper design and ongoing maintenance. company, understands the importance of providing world class
In times when the unexpected occurs, such as natural HVAC service, support, and solutions for customers. Daikin
disasters, mechanical failures, power outages, and or fire can Applied has the expertise to evaluate and recommend system
leave your facility in an unexpected outage situation. upgrades that modernize your existing building within the
The outage can cause: scope of the Leadership in Energy and Environment Design
(LEED) program. Our technicians optimize your current HVAC
• A classroom environment that is difficult to learn in system to get the most efficient system possible to provide
• Loss of instructional days you with energy savings.
• Damage to classroom equipment and supplies
Equipment replacement
• An extended school year
Old, inefficient equipment can be replaced with new technology
Being able to respond quickly and get your HVAC system that offers significantly reduced operating costs. Engineered
working can make all the difference. With the proper plan turnkey assessments and solutions provide the most efficient
in place, you can significantly reduce the time it takes to cost savings equipment or system upgrade, installed seamlessly
get your school back up and running. With a predetermined to get you running efficiently and saving money.
contingency plan, help is just a phone call away. Daikin
Applied is ready to respond 24/7/365 to get you back up and Get your customer plan today
running as soon as possible.
Daikin Applied has a solution for you. To start preparing your
Responses beyond emergencies contingency plan, or to learn more about available services
call 1-800-432-1342. For more information on our complete
Daikin Applied can provide rental chillers when you need extra product lines, visit www.DaikinApplied.com or to find an
cooling during peak season, when you want redundancy, to office near you.
supply cooling during planned maintenance, or to make it
possible for your facility to maintain full cooling capabilities
during retrofit, renovation, or replacement of older equipment.
For more information about our complete line of Parts and Service, contact your local Daikin
Applied Service or visit www.DaikinApplied.com to find an office near you.
GS-07F-0377V ©2015 Daikin Applied | (800) 432-1342 | www.DaikinApplied.com | ASP 31-411
g
GeeAnn Missi
Vice President
Marsh USA LLC
400 W. Market Street
Suite 700
Louisville, KY 40202
502 303 3209
geeann.missi@marsh.com
www.marsh.com
April 1, 2024
Mr. Brian Bayard
Daikin Applied Americas Inc.
13600 Industrial Park Boulevard
Minneapolis, MN 55441
RE: Daikin Applied Americas Inc.
Experience Modification Factor
Dear Brian:
The interstate experience modification factor as calculated by the National Council on Compensation
Insurance, Inc. (NCCI) for Daikin Holdings America, Inc. for the past three years is as follows:
Effective Date Interstate Experience Modification
Factor
4/01/2022 .78
4/01/2023 .70
4/01/2024 .66
If you have any questions, please call me at 502 303-3209 or email at geeann.missi@marsh.com.
Sincerely,
GeeAnn Missi
Air Cond. Equip. Sales, LLC { Richmond - 7500 }
Email: marketing@aceshvac.com
Phone Number: (804) 264-2911
Mailing Address: 7314 Impala Drive, Richmond, Virginia 23228 United States
Shipping Address: 7314 Impala Drive, Richmond, Virginia 23228 United States
Name Email Title
Alley Gordon alleyg@aceshvac.com Admin
Anthony Migliarese anthonym@aceshvac.com Outside Sales
Billy Slaven billys@aceshvac.com Inside Sales
Brett Garner Other
Craig Griffith cgriffith@havtech.com Outside Sales
Craig Griffith craigg@aceshvac.com Outside Sales
David Ziegler davidz@aceshvac.com Outside Sales
Gayle Chumney gaylec@aceshvac.com Admin
Jason Forsythe jasonf@aceshvac.com Inside Sales
Jesse Gibson jesseg@aceshvac.com Controls
Joe Roetering jroetering@thermalhvac.com Principal
Jordan Luntz jluntz@havtech.com Inside Sales
Jordan Whitaker jwhitaker@havtech.com Inside Sales
Kellie Watson kelliew@aceshvac.com Admin
Lauren Martinez laurenm@aceshvac.com Controls
Logan Williams loganw@aceshvac.com Outside Sales
Louis Hite louish@aceshvac.com Controls
Marco n/a Other
Mark Kruse markk@aceshvac.com Controls
Mary Fleming maryf@aceshvac.com Admin
Mike Goetz mikecg@aceshvac.com Inside Sales
Mike Templeton miket@aceshvac.com Outside Sales
Patrick Lloyd patrickl@aceshvac.com Sales Director
Randy Smith randys@aceshvac.com Outside Sales
Sarah Fontaine sarahf@aceshvac.com Other(Accounting)
Scott Pippin scottp@aceshvac.com Outside Sales
Steve Overton soverton@havtech.com Other(Service Supervisor)
Teresa Kirkland teresak@aceshvac.com Admin
Thomas Barrett thomasb@aceshvac.com Controls
Tyler Pippin tylerp@aceshvac.com Sales Support
Air Cond. Equip. Sales, LLC { Roanoke - 2880 }
Email: marketing@aceshvac.com
Phone Number: (540) 595-7139
Mailing Address: 4358 Starkey Road, Suite B, Roanoke, Virginia 24018 United States
Shipping Address: 4358 Starkey Road, Suite B, Roanoke, Virginia 24018 United States
Name Email Title
Chris Beverly cbeverly@havtech.com Outside Sales
Heather Waskey heatherw@aceshvac.com Sales Support
Jeff Wolfe jeffw@aceshvac.com Outside Sales
Joe Roetering jroetering@thermalhvac.com Principal
Justin Vass justinv@aceshvac.com Outside Sales
Patrick Murdock patrickm@aceshvac.com Other(Equipment Sales Manager)
Ryan Coon rcoon@havtech.com Inside Sales
Terry Johnston tjohnston@havtech.com Outside Sales
Wystan Crismond wcrismond@havtech.com Outside Sales
Air Cond. Equip. Sales, LLC { Tidewater - 2870 }
Email: marketing@aceshvac.com
Phone Number: (757) 896-0650
Mailing Address: 105 E Street, Suite 300, Hampton, Virginia 23661 United States
Shipping Address: 105 E Street, Suite 300, Hampton, Virginia 23661 United States
Name Email Title
Ben Sablan bens@aceshvac.com Outside Sales
Chelsea Foley cfoley@havtech.com Outside Sales
Jason Forest jforest@havtech.com Outside Sales
Joe Roetering jroetering@thermalhvac.com Principal
Ken Willett kennethw@aceshvac.com Other(Service Technician)
Melissa Scherbenske mscherbenske@havtech.com Inside Sales
Rohith Shenoy rshenoy@havtech.com Inside Sales
Wade Amos wadea@aceshvac.com Outside Sales
Air Reps, LLC { Portland - 4790 }
Email: kurts@airreps.com
Phone Number: (503) 620-4300
Mailing Address: 15860 SW Upper Boones Ferry Road, Lake Oswego, Oregon 97035-4066 United States
Shipping Address: 15860 SW Upper Boones Ferry Road, Lake Oswego, Oregon 97035-4066 United States
Name Email Title
Adam Benner acbennerman@yahoo.com Other(Service Technician)
Alexandria Bursey alex.bursey@airreps.com Sales Support
Allison McLean allison.mclean@airreps.com Inside Sales
Ben Wallace benw@airreps.com Outside Sales
Blake Millard blake.millard@airreps.com Inside Sales
Byron Gonzalez byron.gonzalez@airreps.com Sales Support
Christopher Aardappel chris.aardappel@airreps.com Other(Service Technician)
Chuck Ross chuck.ross@airreps.com Outside Sales
Connor Sawyer connor.sawyer@airreps.com Other(Service Technician)
Corey Elliott coreye@airreps.com Sales Support
Dave Bradley dave.bradley@airreps.com Inside Sales
Dolan Miles dolanm@oregonairreps.com Other(Application Engineer)
Emmelie Schultheis emmelie.schultheis@airreps.com Sales Support
Eric Danielson eric.danielson@airreps.com Outside Sales
Greg Oberle grego@airreps.com Other(Inside Parts Sales)
Heather Giltner heather.giltner@airreps.com Sales Support
Henry Bauer henryb@airreps.com Outside Sales
Jamey Dennis jameyd@airreps.com Inside Sales
Jean Johnson jean.johnson@airreps.com Other
Justin Lashley justin.lashley@airreps.com Sales Support
Kayla Gamache kayla.gamache@airreps.com Sales Support
Kurt Schultheis kurts@airreps.com Branch Manager
Melanie Rainey melanier@airreps.com Outside Sales
Mike Clark mikec@airreps.com Sales Support
Randy Roesink randyr@oregonairreps.com Other
Rob Grace robg@oregonairreps.com Outside Sales
Robert Grace robg@airreps.com Outside Sales
Ryan Moon ryan.moon@airreps.com Inside Sales
Ryan Thompson ryan.thompson@airreps.com Other(Service Technician)
Scott Caldwell scottc@airreps.com Outside Sales
Stephen Patnode stevep@airreps.com Outside Sales
Steve Patnode stevep@oregonairreps.com Outside Sales
Tyson McGraw tysonm@airreps.com Outside Sales
Vincent Griffith vincent.griffith@airreps.com Outside Sales
William Schultheis william.schultheis@airreps.com Sales Support
Zach Levine zach.levine@airreps.com Inside Sales
Air Reps, LLC { Seattle - 7130 }
Email: daikin@airreps.com
Phone Number: (425) 562-1150
Mailing Address: 3290 146th Place SE,Suite F, Bellevue, Washington 98007 United States
Shipping Address: 3290 146th Place SE,Suite F, Bellevue, Washington 98007 United States
Name Email Title
Aaron Cohn aaronc@airreps.com Inside Sales
Alex Cuevas alex.cuevas@airreps.com Other
Alexander Baker alexander.baker@airreps.com Inside Sales
Anthony Bauserman anthony.bauserman@airreps.com Other
Azlyn Vaughn azlyn.vaughn@airreps.com Inside Sales
Ben Fullingim ben.fullingim@airreps.com Other(Journeyman)
Ben Kulinski ben@airreps.com Outside Sales
Billy Kodosky billy.kodosky@airreps.com Outside Sales
Brett Schafer brett.schafer@airreps.com Inside Sales
Carolina Mironyuk carolina@airreps.com Other(Financial)
Charlie Naylor charlie.naylor@airreps.com Outside Sales
Chris Chornyak chris.chornyak@airreps.com Outside Sales
Christian Vornheder christian@airreps.com Other
Christie Dean christie@airreps.com Inside Sales
Christie Worley christiew@airreps.com Other(Financial)
Colin Holt colin.holt@airreps.com Outside Sales
Collin Van Wyk collin.vanwyk@airreps.com Inside Sales
Corey Jenks coreye@airreps.com Other(Applications Engineer)
Crystal Faulkner crystalf@airreps.com Inside Sales
Dana Moffat dana.moffat@airreps.com Outside Sales
Dave Greenheck dave.greenheck@airreps.com Inside Sales
David Osborne davido@airreps.com Inside Sales
Eudoxie Hudry eudoxie.hudry@airreps.com Inside Sales
Heath Haley heath@airreps.com Principal
Henry Winn henry.winn@airreps.com Inside Sales
Isabella Griffen isabellag@airreps.com Inside Sales
Jack Stutz jack.stutz@airreps.com Inside Sales
James n/a jjensen@gmail.com Other
James Winn james@airreps.com Outside Sales
Jamie Dennis jameyd@airreps.com Inside Sales
Jamie Love jamiel@airreps.com Admin
Janel Farwell janel@airreps.com Project Developer/Manager
Jayme Patton jayme.patton@airreps.com Inside Sales
Jim Boles jim@airreps.com Inside Sales
Jim Gundry jimg@airreps.com Other(VRV Specialist)
Joel Cook joel.cook@airreps.com Inside Sales
Josh Gary josh@airreps.com Inside Sales
Josh More joshm@airreps.com Other(ABB Drive Specialist)
Josh Scott josh.scott@airreps.com Inside Sales
Justin Milone justin.milone@airreps.com Inside Sales
Kate Kulinski-Howe kateh@airreps.com Other(Application Engineering Apprentice)
Ken Horsfall khorsfall@airreps.com Inside Sales
Ken Owens kowens@airreps.com Other(Account Executive)
Ken Porter kporter@airreps.com Sales Director
Kendra Luwe kendra.luwe@airreps.com Project Developer/Manager
Kevin Bates kevnb@integratedsc.net Other
Kodi Aller kodi.aller@airreps.com Other
Kyle Hawkins kyle.hawkins@airreps.com Other(System Administrator)
Lauren Rabren lauren.rabren@airreps.com Inside Sales
Lecia Bailey lecia.bailey@airreps.com Project Developer/Manager
Lecia Belinc lecia.belinc@airreps.com Project Developer/Manager
Lee Yalkapov lee@utspro.com Other(IT Support)
Mark Cotter jameyd@airreps.com Inside Sales
Mark Crudge mark.crudge@airreps.com Outside Sales
Mark Ojendyk mark@airreps.com Other(Account Executive)
Mark Potter markp@airreps.com Admin
Matt Adkins matt@airreps.com Other(Account Executive)
Matt Gregg mattg@airreps.com Other(Account Executive)
Meagan Sullivan meagan.sullivan@airreps.com Admin
Michael Hawkins michael@airreps.com Principal
Mike Elger mike.elger@airreps.com Other(Applications Engineer)
Mike Zimmerman mikez@airreps.com Other(Account Executive)
Owen Krueger owen@airreps.com Other
Peter Morris peter.morris@airreps.com Inside Sales
Rainie Chiu rainie.chiu@airreps.com Inside Sales
Ricky Welch ricky.welch@daikinapplied.com Inside Sales
Robert Grace robg@airreps.com Outside Sales
Ron Asmus ron@airreps.com Other(Financial)
Ryan Brown rbrown@airreps.com Other(Applications Engineer)
Ryan Stewart ryans@airreps.com Inside Sales(Parts Manager)
Ryan Stotts ryan.stotts@airreps.com Other
Ryan Thompson ryan.thomson@airreps.com Inside Sales
Samantha Johnson samantha.johnson@airreps.com Inside Sales
Scott Douglas scott.douglas@airreps.com Outside Sales
Sean Koenig sean.koenig@airreps.com Other
Stephanie Young stephanie.young@airreps.com Inside Sales
Tim Camarata tim.camarata@airreps.com Outside Sales
Tucker Carlson tucker.carlson@airreps.com Inside Sales
Tyler Jones tyler.jones@airreps.com Outside Sales
Whitney Walker whitney@airreps.com Other(Account Executive)
Air Reps, LLC { Spokane - 7140 }
Email: gnelson@airreps.com
Phone Number: (509) 465-8038
Mailing Address: 1710 N. Calispel Street, Suite A, Spokane, Washington 99205 United States
Shipping Address: 1710 N. Calispel Street, Suite A, Spokane, Washington 99205 United States
Name Email Title
Adam Flowers adam.flowers@airreps.com Sales Support
Ben Fullingim ben.fullingim@airreps.com Other(Journeyman)
Charley Rodgers crodgers@airreps.com Outside Sales
Denise Munson denise@airreps.com Sales Support
Eric Williams eric.williams@airreps.com Outside Sales
Jared Haight jared.haight@airreps.com Outside Sales
John Keen john.keen@airreps.com Inside Sales
Kraig Guerin kraig@airreps.com Outside Sales
Lynn Helms lynn.helms@airreps.com Other(Technician)
Rick Sterling rick.sterling@airreps.com Other(Service)
Tami Brink tbrink@airreps.com Sales Support
Theresa Buchanan theresa.buchanan@airreps.com Inside Sales
Air Tech Equipment Inc. { Grand Rapids - 1010 }
Email: sales@airtechequipment.com
Phone Number: (616) 534-0032
Mailing Address: 3523 Lousma Drive, Grand Rapids, Michigan 49548 United States
Shipping Address: 3523 Lousma Drive, Grand Rapids, Michigan 49548 United States
Name Email Title
AJ Diggs aj@airtechequipment.com Other(Parts)
Andrew Bettis abettis@airtecperforms.com Other
Cal Johnson cal@airtechequipment.com Outside Sales
Chris Stebbins-Nutt chrisn@airtechequipment.com Outside Sales
Clint Sumner clint@airtechequipment.com Other
Donald Smeal don@airtechequipment.com Controls
Dylan Roberts droberts@airtechequipment.com Inside Sales
Erin Smeal esmeal@airtechequipment.com Other(Service Sales)
Francis Alvarez Other
Frank Pointe frank@airtechequipment.com Outside Sales
Gary Walker garyw@airtechequipment.com Controls
Jacob Pointe jpointe@airtechequipment.com Outside Sales
James Mester james.mester@airtechequipment.com Inside Sales
Jason Rutkowski jason@airtechequipment.com Other
Jeff Royston jeff@airtechequipment.com Outside Sales
Jeromy LaRock jeromy@airtechequipment.com Outside Sales
John Cassady IV john@airtechequipment.com Outside Sales
John Wise Other
Josh Suzio jsuzio@airtechequipment.com Other
Judy Stocking judy@airtechequipment.com Other(Parts Assistant)
Junise Arnold junise@airtechequipment.com Other(Office Manager)
Kim Koltak kim@airtechequipment.com Inside Sales
Kyle McLeod kyle@airtechequipment.com Principal
Laurie LaCharite laurie@airtechequipment.com Inside Sales
Lucas Lowe llowe@airtechequipment.com Outside Sales
Mark Pell mark@airtechequipment.com Other
Mark Pell mark@airtechequipment.com Outside Sales
Marvin Smeal marvin@airtechequipment.com Other
Megan Mayle megan@airtechequipment.com Outside Sales
RObert Polson robert@airtechmech.com Other
Sydney Princing sydney@airtechequipment.com Inside Sales
Tammy Weesaw tammy@airtechequipment.com Other(Office Admininstrator)
Todd Vigh todd@airtechequipment.com Principal
Trevor Fink trevor@airtechequipment.com Controls
Air-Tech of Pensacola { Pensacola - 5400 }
Email: darren@airtechfl.com
Phone Number: (850) 433-6443
Mailing Address: P.O. Box 18180, Pensacola, Florida 32505 United States
Shipping Address: 2317 Town Street, Pensacola, Florida 32505 United States
Name Email Title
Bryan Alvarez aztechservices@gmail.com Other
Chris Rodriguez chris12533@gmail.com Other
Derrick Paul dpaul@airtechfl.com Other
Gianna Kahlhammer gianna@airtechequipment.com Other
Jeff Williams jawilliams@airtechfl.com Other
John Huffaker john.huffaker@airetechcorp.com Other
Mark Jameson mark.jameson@airetechcorp.com Other
Rolando Ortiz rortiz@airtecperforms.com Other
Briggs Equipment Sales { Portland - 2540 }
Email: bbriggs@briggsac.com
Phone Number: (207) 657-7123
Mailing Address: P.O. Box 1375, Gray, Maine 04039-1375 United States
Shipping Address: 16 NorthBrook Drive, Gray, Maine 04039-1375 United States
Name Email Title
AnnMarie Juliano ajuliano@briggsac.com Sales Support
Benjamin Briggs benbriggs@briggsac.com Sales Support
Brian Briggs bbriggs@briggsac.com Principal
Bruce Briggs brucebriggs@briggsac.com Sales Support
James Lacombe jlacombe@briggsac.com Other(Service Manager)
Marcel Vachon admin@briggsac.com Admin
Michael Lovelette mlovelette@briggsac.com Other(Parts)
Spencer Brown sbrown@briggsac.com Sales Support
Terry Girouard tgirouard@briggsac.com Other(Finance)
Tyler Harlow tharlow@briggsac.com Other(Service Tech)
Brooks Building Solutions Inc. { Jacksonville - 1080 }
Email: bbsequipmentsalesgroup@brookssolutions.net
Phone Number: (904) 642-5303
Mailing Address: 4501 Beverly Avenue, Jacksonville, Florida 32210 United States
Shipping Address: 4501 Beverly Avenue, Jacksonville, Florida 32210 United States
Name Email Title
Adam Beauregard abeauregard@brookssolutions.net Other(Service Tech)
Alexandra Serlin aserlin@brookssolutions.net Principal
Anthony Di Clemente adiclemente@brookssolutions.net Inside Sales
Barry Wittenkeller bwittenkeller@brookssolutions.net Other(Service Estimator)
Becky Hartley bhartley@brookssolutions.net Other(Corporate Accountant)
Ben Biscuit Other
Billy Miles bmiles@brookssolutions.net Office Manager
Blaire Rhoads brhoads@brookssolutions.net Other
Brad Tepper btepper@brookssolutions.net Other(Equipment Sls Manager)
Brent Perry bperry@brookssolutions.net Other(Service Coordinator)
Caroline Jury cjury@brookssolutions.net Other(Service Sales Engineer)
Cat Stinson cstinson@brookssolutions.net Other(Financial Officer)
Charles Francis kfrancis@brookssolutions.net Other(Financial Officer)
Chris Forkey cforkey@brookssolutions.net Inside Sales
Chris McGill cmcgill@brookssolutions.net Outside Sales
Christian Niebling cniebling@brookssolutions.net Inside Sales
Dustin Morgan dmorgan@brookssolutions.net Other(Service Technician)
Dwayne Umstattd dumstattd@brooksolutions.net Outside Sales
Dwayne Umstattd dumstattd@brookssolutions.net Office Manager
Eamonn Benson ebenson@brookssolutions.net Controls
Edgardo Diaz ediaz@brookssolutions.net Inside Sales
James Garrow jgarrow@brookssolutions.net Other(Service Technician)
James Hendricks jhendricks@brookssolutions.net Inside Sales
Jason Barrett jbarrett@brookssolutions.net Inside Sales
Jeremy Swilley jswilley@brooksair.com Other
Josh Whitley jwhitley@brookssolutions.net Inside Sales
Joshua Rippke jrippke@brookssolutions.net Other(Service Technician)
Katelyn Tyler ktyler@brookssolutions.net Outside Sales
Kurt Devee kdevee@brookssolutions.net Inside Sales
Matt Updegraff mupdegraff@brookssolutions.net Other
Matthew Johns mjohns@brookssolutions.net Other
Megan Yarborough myarborough@brookssolutions.net Other
Michael Goley mgoley@brookssolutions.net Other
Nash Toler ntoler@brookssolutions.net Other
Neff Jenkins njenkins@brookssolutions.net Principal
Nichole St. Clair nstclair@brookssolutions.net Office Manager
Quinn Shay qshay@brookssolutions.net Other
Rachel Miller rmiller@brookssolutions.net Controls
Rick Berryhill rberryhill@brookssolutions.net Other(Service Technician)
Ricky Chavarriaga cchavar@icloud.com Other
Rudy Arrington rarrington@brookssolutions.net Other(Service Technician)
Russ Gillette rgillette@brookssolutions.net Outside Sales
Shermaine Auguste sauguste@brookssolutions.net Other
Stephanie MacKendree smackendree@brookssolutions.net Other(Human Resources)
Stewart Galligher sgalligher@brookssolutions.net Outside Sales
Tauno Kyllonen jr Other(Trained WMC, Cent)
Tom McGuire tmcguire@brookssolutions.net Other(Service Sales Manager)
Tony Porto tporto@brookssolutions.net Other(Project Manager)
Trevor Gillespie tgillespie@brookssolutions.net Inside Sales
Brooks Building Solutions Inc. { Tallahassee - 1080A }
Email: bbequipmentsalesgroup@brookssolutions.net
Phone Number: (850) 701-2350
Mailing Address: 2815-A Industrial Plaza Drive, Tallahassee, Florida 32301 United States
Shipping Address: 2815-A Industrial Plaza Drive, Tallahassee, Florida 32301 United States
Name Email Title
Chuck Pierson cpierson@brookssolutions.net Inside Sales
Keith North knorth@brookssolutions.net Other(Employee)
Mark Fleschner mfleschner@brookssolutions.net Inside Sales
Peter House phouse@brookssolutions.net Inside Sales
Wildred (Wil) Humes whumes@brookssolutions.net Other(Service Technician)
D&B Building Solutions LLC { Bloomfield - 1620 }
Email: ayamazaki@dbnj.com
Phone Number: (973) 429-2828
Mailing Address: 444 JFK Drive, Bloomfield, New Jersey 07003 United States
Shipping Address: 444 JFK DRIVE, BLOOMFIELD, New Jersey 07003 United States
Name Email Title
Aiden Richter intern@dbbs.com Inside Sales
Alexander Zelenka azelenka@dbbs.com Outside Sales
Ana Santos asantos@dbbs.com Inside Sales
Andrew Bassily abassily@dbbs.com Outside Sales
Ayumi Yamazaki ayamazaki@dbnj.com Estimator
Brian Tenedine btenedine@dbnj.com Outside Sales
Bruno Rzeszutko brzeszutko@dbnj.com Outside Sales
Casara Sexauer csexauer@dbbs.com Inside Sales
Christopher Pedecine cpedecine@dbnj.com Principal
Colin Trevors ctrevors@dbnj.com Other
Conor Casey ccasey@dbnj.com Inside Sales
Courtney Lalanne clalanne@dbnj.com Other(Accountant)
Cristiana Goncalves cgoncalves@dbnj.com Other(accountant)
Dan Daniello ddaniello@dbbs.com Outside Sales
Edward O'Connor eoconnor@dbbs.com Principal
Edwin Pacheco epacheco@dbnj.com Other(Accounting)
Eric Burger eburger@dbbs.com Principal
Gene Boehne gboehne@dbbs.com Outside Sales
Greg Santos gsantos@dbbs.com Inside Sales
Husein Kapadia hkapadia@dbbs.com Inside Sales
James Griffiths jgriffiths@dbbs.com Other(Service)
Jeffrey Barat jnbarat@dbnj.com Outside Sales
Jenn Olivo jolivo@dbbs.com Inside Sales
Joe Deacy jdeacy@dbnj.com Other(District Operations Supervisor)
John O'Krinsky jokrinsky@dbbs.com Outside Sales
John Taguer jtaguer@dbnj.com Outside Sales
Jonathan Palumbo jpalumbo@dbnj.com Other(Service Director)
Karen Rivera krivera@dbnj.com Other(Billing Administrator)
Kari Vander Weit kvanderweit@dbnj.com Office Manager
Lewis Ischinger lischinger@dbnj.com Other(SSR)
Liard Weston lweston@dbbs.com Other(Sales Engineer)
Liard Weston lweston@dbbs.com Outside Sales
Malak Ejjaki mejjaki@dbnj.com Inside Sales
Maria Cruz mcruz@dbbs.com Inside Sales
Matthew Roufaeal mroufaeal@dbnj.com Inside Sales
Michael Lindner mlindner@dbbs.com Outside Sales
Michael Sommerville msommerville@dbbs.com Outside Sales
Michael Winer mwiner@dbnj.com CFO
Nicholas Ciasulli intern2@dbbs.com Inside Sales
Nick Allocco nallocco@dbbs.com Inside Sales
Nicole Ciaravino nciaravino@dbnj.com Inside Sales
Philip Temporado dbsg.support@dbbs.com Inside Sales
Rachel Barat rgbarat@dbnj.com Other
Rick Bariletto rbariletto@dbbs.com Outside Sales
Rick Hakes rhakes@dbbs.com Other
Stephanie Amico samico@dbnj.com Other
Stephen Mawhinney smawhinney@dbbs.com Outside Sales
Ted Moran tmoran@dbbs.com Outside Sales
Thomas George tgeorge@dbbs.com Project Developer/Manager
Tom Hanville thanville@dbbs.com Other
Tonja Bowden tbowden@dbbs.com Sales Support
Vilma Useva vuseva@dbnj.com Inside Sales
William Hill billhill@dbbs.com Outside Sales
William Howard whoward@dbnj.com Project Developer/Manager
Daikin Applied (previously Carroll Air Systems) { Ft. Myers - 3010A }
Email: cas-ftm@carrollair.com
Phone Number: (239) 939-5553
Mailing Address: 5840 Halifax Avenue, Ft. Myers, Florida 33912 United States
Shipping Address: 5840 Halifax Avenue, Ft. Myers, Florida 33912 United States
Name Email Title
Allison Valley avalley@carrollair.com Other(Parts)
Neville Pancham npancham@carrollair.com Other
Stacy Fritsch sfritsch@carrollair.com Inside Sales
Stacy Fritsch sfritsch@carrollair.com Other(Employee)
Suzann (Suzy) Bell carrollair-ftm@carrollair.com Other(Administrative Assistant)
Daikin Applied (previously Carroll Air Systems) { Orlando - 3040 }
Email: cas-orl@carrollair.com
Phone Number: (407) 831-4880
Mailing Address: 4525 Vineland Road, Suite 205, Orlando, Florida 32811 United States
Shipping Address: 4525 Vineland Road, Suite 205, Orlando, Florida 32811 United States
Name Email Title
Austin Stewart astewart@carrollair.com Inside Sales
Bruce Tindle btindle@carrollair.com Outside Sales
Christine Christy cchristy@carrollair.com Other(Sales Coordinator)
Corey Fuller cfuller@carrollair.com Inside Sales
David Carroll dcarroll@carrollair.com Outside Sales
Derek Schaening dschaening@carrollair.com Other(IT Support)
Jordan Anderson janderson@carrollair.com Outside Sales
Lance Hutchison lance.hutchinson@daikinapplied.com Other(Service Technician)
Laura Taylor ltaylor@carrollair.com Inside Sales
Marc Canas marc.canas@daikinapplied.com Other(Technician)
Matt Neff mneff@carrollair.com Other(Support)
Melissa Dyal mdyal@carrollair.com Inside Sales(Sales Coordinator)
Mohammad Fida mohammad.fida@daikinapplied.com Inside Sales
Nick Nicoles Other(Support)
Rick Conklin rconklin@carrollair.com Outside Sales
Robert Teetsel rteetsel@carrollair.com Outside Sales
Sondra Kennett skennett@carrollair.com Inside Sales
Todd Moore tmoore@carrollair.com Branch Manager
Daikin Applied (previously Carroll Air Systems) { Tampa - 3010 }
Email: cas-tpa@carrollair.com
Phone Number: (813) 879-5790
Mailing Address: 3711 W. Walnut St., Tampa, Florida 33607 United States
Shipping Address: 3711 W. Walnut St., Tampa, Florida 33607 United States
Name Email Title
Allison Valley avalley@carrollair.com Other(Parts)
Andrew Kee akee@carrollair.com Branch Manager
Bob Mulholland bmulholland@carrollair.com Other(Project Engineer)
Brett Daugherty brett.daugherty@daikinapplied.com Other(Service Tech)
Charles Passman, P.E. cpassman@carrollair.com Inside Sales
Cheryl Gentry cgentry@carrollair.com Other(Admin Assistant III)
Connor Kee connor.kee@daikinapplied.com Inside Sales
Debie Horsey dhorsey@carrollair.com Outside Sales
Doug Waldecker dwaldecker@carrollair.com Other(Service Tech)
Frank Vibbert fvibbert@carrollair.com Principal
Jackson Buchanan jackson.buchanan@daikinapplied.com Other(Technician)
Jason Cuesta jcuesta@carrollair.com Inside Sales
Mark Cartmell mcartmell@carrollair.com Principal
Michael Karakourtis mkarakourtis@carrollair.com Outside Sales
Michael Nies michael.nies@daikinapplied.com Outside Sales
Michele Mulligan michele.mulligan@daikinapplied.com Other(Parts/Service Admin)
Nick Demarco nicholas.demarco@daikinapplied.com Other
Nicole Younglove-Williams nyounglove@carrollair.com CFO
Pamela Gehan pgehan@carrollair.com Other(Accountant)
Paul Kellar paul.kellar@daikinapplied.com Outside Sales
Philip Carroll philip.carroll@daikinapplied.com Principal
Renee Werking rwerking@carrollair.com Other(Administrative Assistant II)
Richard Sechrist richard.sechrist@daikinapplied.com Admin
Samantha Marien samantha.marien@daikinapplied.com Outside Sales(Outside Sales)
Stuart Waag swaag@carrollair.com Outside Sales
Stuart Waag, P.E. swaag@carrollair.com Outside Sales
Suzann Bell suzann.bell@daikin.applied.com Inside Sales
Taelor Nolen taelor.nolen@daikinapplied.com Other(Parts & Aftermarket Sales Associate)
Thomas Peeples, P.E. tpeeples@carrollair.com Sales Director
Willie Valentin wvalentin@carrollair.com Inside Sales
Willie Wouters wwouters@carrollair.com Inside Sales
Daikin Applied Birmingham { Hoover - 4880 }
Email: john.jeffcoat@daikinapplied.com
Phone Number: (205) 989-4370
Mailing Address: 245 Riverchase Pkwy E,Suite O, Hoover, Alabama 35244 United States
Shipping Address: 245 Riverchase Pkwy E,Suite O, Hoover, Alabama 35244 United States
Name Email Title
Angie Brand angie.brand@mcquay.co.uk Other(Employee)
Austin Clark austin.clark@daikinapplied.com Inside Sales
Bryson Hatcher bryson.hatcher@daikinapplied.com Inside Sales
Carol Sorvick carol.sorvick@daikinapplied.com Other(Employee)
Carson Cooper carson.cooper@daikinapplied.com Outside Sales
Cicily Tinney cicily.tinney@daikinapplied.com Project Developer/Manager
David Ridlespurge david.ridlespurge@daikinapplied.com Other(Service Supervisor)
Dawn Dimopoulos dawn.dimopoulos@mcquay.co.uk Other(Employee)
Elinor Nilsson elinor.nilsson@daikinapplied.com Project Developer/Manager
Erik Norrell erik.norrell@daikinapplied.com Other(Outside Sales)
Evan Grovenstein evan.grovenstein@daikinapplied.com Outside Sales
Haynes Litchfield haynes.litchfield@daikinapplied.com Outside Sales
James Wills james.wills@daikinapplied.com Other(Employee)
Jason Emiliusen jason.emiliusen@daikinapplied.com Other(Employee)
Jeremiah Bishop jeremiah.bishop@daikinapplied.com Outside Sales
John Hix john.hix@daikinapplied.com Outside Sales
John Jeffcoat john.jeffcoat@daikinapplied.com Branch Manager
Lauren Pike lauren.pike@daikinapplied.com Project Developer/Manager
Mark Dengate mark.dengate@daikinapplied.com Outside Sales
Mark Wieland mark.wieland@daikinapplied.com Other(Sales)
Michael Franklin michael.franklin@daikinapplied.com Project Developer/Manager
Nick Iannuzzi nick.iannuzzi@daikinapplied.com Outside Sales
Pam Reiser pam-reiser@daikinapplied.com Other(Employee)
Pat Bryson pat.bryson@daikinapplied.com Other(Employee)
Randy Hoosier randy.hossier@daikinapplied.com Other(Employee)
Robert Smith robert.smith@daikinapplied.com Principal
Rustin Johnston rustin.johnson@daikinmcquay.com Other(Employee)
Steven Lewis steven.lewis@daikinapplied.com Project Developer/Manager
Susanto Agustina susanto@daikinapplied.co.id Other(Employee)
Ted Hershey ted.hershey@daikinapplied.com Other(Employee)
Tricia Elliott tricia.elliott@daikinapplied.com Inside Sales(Employee)
Vikki Love vikki.love@daikinapplied.com Project Developer/Manager
Daikin Applied Georgia { Marietta - 4110 }
Email: mark.schnetzka@daikinapplied.com
Phone Number: (770) 514-5880
Mailing Address: 425 Franklin Gateway, Suite 550, Marietta, Georgia 30067 United States
Shipping Address: 425 Franklin Gateway, Suite 550, Marietta, Georgia 30067 United States
Name Email Title
Alan Zeigler alan.zeigler@daikinapplied.com Outside Sales
Alexandra Edinger alexandra.edinger@daikinapplied.com Other(Field Sales Engineer)
Amy Bampfield amy.bampfield@daikinapplied.com Other(Service Coordinator)
Andrea Cousins andrea.cousins@daikinapplied.com Other(Employee)
Angelly Castro angelly.castro@daikinapplied.com Inside Sales
Ashley Whatley ashley.whatley@daikinapplied.com Inside Sales
Bernie Smith smith.bernie@daikinapplied.com Other(Employee)
Beverly Peek beverly.peek@daikinapplied.com Inside Sales
Crystal Zickefoose crystal.zickefoose@daikinapplied.com Other(Sr. Financial Analyst)
Dale Maloney dale.maloney@daikinapplied.com Outside Sales
Daniel Brobjorg danb@svl.com Outside Sales
Donna Legrand donna.legrand@daikinapplied.com Other(Employee)
Eric Lee eric.lee@daikinapplied.com Inside Sales
Ernest (Shannon) Willis ernest.willis@daikinapplied.com Other(Field Sales Engineer)
Federico Anderson federico.anderson@daikinapplied.com Inside Sales
Grace Sinclair grace.sinclair@daikinapplied.com Inside Sales
Jason Peck jason.peck@daikinapplied.com Outside Sales
Jeannie Sullivan jeannie.sullivan@daikinapplied.com Sales Support
Jeff Minton jeff.minton@daikinapplied.com Outside Sales
John Jagusztyn john.jagusztyn@daikinapplied.com Outside Sales
Jon-Michael Conger jon-michael.conger@daikinapplied.com Inside Sales
Kaleb Kroells kaleb.kroells@daikinapplied.com Other(Accounting Manager)
Kirsten Schulte kirsten.schulte@daikinapplied.com Outside Sales
Lauretta Lovejoy lauretta.lovejoy@daikinapplied.com Inside Sales
Maria Spoor maria.spoor@daikinapplied.com Admin(Project Engineer)
Mark Schnetzka mark.schnetzka@daikinapplied.com Principal
Mark Staab mark.staab@daikinapplied.com Other(Project Engineer)
Matthew O'Brien matthew.obrien@daikinapplied.com Outside Sales
Matthew Prather matthew.prather@daikinapplied.com Outside Sales
Matthew Schnetzka matthew.schnetzka@daikinapplied.com Inside Sales
Matthew-Michael Hines matthew.hines@daikinapplied.com Inside Sales
Mazen Mansur mazen.mansur@daikinapplied.com Principal
Michael Garrett michael.garrett@daikinapplied.com Outside Sales
Michael Jessee michael.jessee@daikinapplied.com Other(SSR)
Patrick Leake patrick.leake1@daikinapplied.com Outside Sales
Patrick Tramonte patrick.tramonte@daikinapplied.com Outside Sales
Phillip Sinclair philip.sinclair@daikinapplied.com Inside Sales
Prem Shetty prem.shetty@daikinapplied.com Outside Sales
Ryan Sinykin ryan.sinykin@daikinapplied.com Other(Representative-Cust Serv III)
Shakaile Bell shakaile.bell@daikinapplied.com Sales Support
Shane Clawges shane.clawges@daikinapplied.com Inside Sales
Steven Lwin steven.lwin@daikinapplied.com Inside Sales
Tasha Cayton tasha.cayton@daikinapplied.com Inside Sales
Thomas Freet thomas.freet@daikinapplied.com Other(Admin)
Tony Falcicchio tony.falcicchio@daikinapplied.com Other(ATS Warranty Administrator)
Walton Wade walton.wade@daikinapplied.com Inside Sales
Daikin Applied Modular Solutions { Phoenix - 7160 }
Email:
Phone Number: 111-111-1111
Mailing Address: 4940 West Lower Buckeye Road, Phoenix, Arizona 85043 United States
Shipping Address: 4940 West Lower Buckeye Road, Phoenix, Arizona 85043 United States
Name Email Title
Alexander Lascau alexander.lascau1@daikinapplied.com Other(mcp)
Douglas Lovell douglas.lovell@daikinapplied.com Other(Support)
Ryan Culp ryan.culp@daikinapplied.com Inside Sales
Daikin Applied New York { Jersey City - 4400 }
Email: marian.sorial@daikinapplied.com
Phone Number: (201) 395-3750
Mailing Address: 10 Exchange Place,21st Floor, Jersey City, New Jersey 07302 United States
Shipping Address: 10 Exchange Place,21st Floor, Jersey City, New Jersey 07302 United States
Name Email Title
Ajay Thumar ajay.thumar@daikinapplied.com Inside Sales(Project Engineer)
Andrew Arndt andrew.arndt@daikinapplied.com Outside Sales(FSE)
Branko Djuretic branko.djuretic@daikinapplied.com Inside Sales
Brian Cohn brian.cohn@daikinapplied.com GM/VP
Brian Meyer brian.meyer@daikinapplied.com Outside Sales
Bryan Kurdziel bryan.kurdziel@daikinapplied.com Outside Sales
Carl Caserta carl.caserta@daikinapplied.com Outside Sales(FSE)
Christian Niebling christian.niebling@daikinapplied.com Outside Sales
Christopher Wilson christopher.wilson@daikinapplied.com Other(DSO Sales Manager)
Cynthia Vest cynthia.vest@daikinapplied.com Other(Support)
Doug DeVoe doug@hgunyc.com Other(Support)
Emma Roth emma.roth@daikinapplied.com Inside Sales
Eric Joseph eric.joseph@daikinapplied.com Outside Sales(FSE)
Genesis Osorio genesis.osorio@daikinapplied.com Inside Sales(Project Engineer)
Gerald Restubog gerald.restubog@daikinapplied.com Outside Sales(FSE)
Huili (Danny) Shi huili.shi@daikinapplied.com Other(Support)
Ian Cabatuan ian.cabatuan@daikinapplied.com Other(Employee)
Indiana Acosta indiana.acosta@daikinapplied.com Inside Sales
JaVonne Greene javonne.greene@daikinapplied.com Admin
John Koerwer john.koerwer@daikinapplied.com Outside Sales(FSE)
John Santoro john.santoro@daikinapplied.com Outside Sales(Sales Manager)
Jonathan Mehr jonathan.mehr@daikinapplied.com Outside Sales(FSE)
Joshua Krantz joshua.krantz@daikinapplied.com Outside Sales
Juliet Orgill juliet.orgill@daikinapplied.com Outside Sales(FSE)
Ken Mueller ken.mueller@daikinapplied.com Outside Sales(FSE)
Kevin Pak kevin.pak@daikinapplied.com Estimator
Kevin Vradenburg kevin.vradenburg@daikinapplied.com Outside Sales(FSE)
Lauren Stephens lauren.stephens@daikinapplied.com Other(Employee)
Marian Sorial marian.sorial@daikinapplied.com Other(Operations Manager)
Michael Calvano michael.calvano@daikinapplied.com Other(Employee)
Miguel Beltran miguel.beltran@daikinapplied.com Inside Sales
Miquel Quiroz jose.quiroz@daikinapplied.com Other(Service Technician)
Omar Eleesily omar.eleesily@daikinapplied.com Inside Sales
Paul Phillips paul.phillips@daikinapplied.com Other
Peter Sterling peter.sperling@daikinapplied.com Other(Support)
Philana Owusu philana.owusu@daikinmcquay.com Other(Employee)
Philip Russo philip.russo@daikinapplied.com Outside Sales(FSE)
Richard Haigh richard.haigh@daikinapplied.com Inside Sales
Robert Lisse bob.lisse@daikinapplied.com Principal
Roberta Bode roberta.bode@daikinapplied.com Other(Sales Coordinator)
Rose Pagan rose.pagan@daikinapplied.com Office Manager
Scott Shufflebotham scott.shufflebotham@daikinapplied.com Outside Sales(FSE)
Shivam Patel shivam.patel@daikinapplied.com Inside Sales
Sonia Uddin sonia.uddin@daikinapplied.com Inside Sales
Steve Burnett steve.burnett@daikinapplied.com Outside Sales(Support)
Thomas Linkus thomas.linkus@daikinapplied.com Inside Sales
Todd Korte todd.korte@daikinapplied.com Outside Sales
Vergil Cabatuan vergil.cabatuan@daikinapplied.com Inside Sales
Zachary Everett zachary.everett@daikinapplied.com Outside Sales
Daikin Applied Plymouth { Plymouth - 3200 }
Email: mcquayintl@daikinapplied.com
Phone Number: (763) 553-5330
Mailing Address: 13600 Industrial Park Blvd., Plymouth, Minnesota 55441 United States
Shipping Address: 13600 Industrial Park Blvd., Plymouth, Minnesota 55441 United States
Name Email Title
Andrew Luers andrew.luers@daikinapplied.com Other(Sr. Business Analyst)
Jacob Anderson jacob.anderson@daikinapplied.com Other(Designer III -Drafting)
James (Jay) Roche james.roche@daikinapplied.com Inside Sales(Employee)
Luke Test john.huebner@daikinapplied.com Other(Technician)
Manuel De Paz manuel.depaz@daikinapplied.com Other(Support)
Mark Ennenga mark.ennenga@daikinapplied.com Other(Engineer - Sales App IV)
Rachel Love rachel.love@daikinapplied.com Other
Samih Terhzaz samih.terhzaz@daikinapplied.com Other(Data Center Order Delivery Manager)
Scott Martens scott.martens@daikinapplied.com Other(Technician)
Sengpasard Munnicha sengpasard.munnicha@daikinapplied.com Other(Intern)
Teresa Larson teresa.larson@daikinapplied.com Other(Accountant II)
Test E2CP test@e2cp.com Other
Victor Justavino victor.justavino@daikinapplied.com Other(Sr HVAC Technical Instructor)
Zachary Boettcher zachary.boettcher@daikinapplied.com Other(Product Specialist, Parts)
Daikin Applied South Florida { Davie - 4150 }
Email: barbara.tarr@daikinapplied.com
Phone Number: (954) 862-8500
Mailing Address: 15712 SW 41st Street,Suite 6, Davie, Florida 33331 United States
Shipping Address: 15712 SW 41st Street,Suite 6, Davie, Florida 33331 United States
Name Email Title
Adam Cornell adam.cornell@daikinapplied.com Other(Regional Parts Sales Manager)
Alberto Juarez alberto.juarez@daikinapplied.com Outside Sales
Annamara Oramas annamara.oramas@daikinapplied.com Sales Support
Antigoni Lathiris antigoni.lathiris@daikinapplied.com Other(Employee)
Ayane Ishida ayane.ishida@daikinapplied.com Inside Sales
Barbara Tarr - Termed 12/16/22 barbara.tarr@daikinapplied.com Other(Financial Officer)
Danylka Forzan danylka.forzan@daikinapplied.com Inside Sales
David Diaz david.diaz@daikinapplied.com Other(Executive Sales Engineer)
Gianni Calandriello gianni.calandriello@daikinapplied.com Other(Aftermarket and Parts Sales)
Gordon Wilkinson gordon.wilkinson@daikinapplied.com Other(Branch Operations Manager)
Guillermo Anson guillermo.anson@daikinapplied.com Other(Parts Sales Specialist)
Ivan Velez ivan.velez@daikinapplied.com Outside Sales
Jose Carreno jose.carreno@daikinapplied.com Inside Sales
Luis Coello luis.coello@daikinapplied.com Outside Sales
Luis Morales luis.morales@daikinapplied.com Inside Sales
Miguel Quiles miguel.quiles@daikinapplied.com Outside Sales
Nico Yanez nicolas.yanez@daikinapplied.com Inside Sales
Pat Rick pat.rick@daikinapplied.com Other(Technician)
Raul Palacios raul.palacios@daikinapplied.com GM/VP
Roberto Siewert roberto.siewert@daikinapplied.com Outside Sales
Rodolfo Victores rodolfo.victores@daikinapplied.com Other(Field Sales Engineer)
Ryan Azore ryan.azore@daikinapplied.com Inside Sales
Simon Diez simon.diez@daikinapplied.com Outside Sales
Sonia Arranaga sonia.arranaga@daikinapplied.com Other(Senior Sales Engineer)
Steven Garcia steven.garcia@daikinapplied.com Inside Sales
Tedd Jagusztyn tedd.jagusztyn@daikinapplied.com Outside Sales
Ty Tran ty.tran@daikinapplied.com Project Developer/Manager
Vicente Ciliberti vicente.ciliberti@daikinapplied.com Inside Sales(Service Sales Rep)
Victor Baumzweig victor.baumzweig@daikinapplied.com Branch Manager
Yvonne Lopez yvonne.lopez@daikinapplied.com Inside Sales
Daikin TMI LLC { Kansas City - 6780 }
Email: wes.hueseman@tmi-stl.com
Phone Number: (816) 298-6281
Mailing Address: 8014 Flint Street, Lenexa, Kansas 66214 United States
Shipping Address: 8014 Flint Street, Lenexa, Kansas 66214 United States
Name Email Title
Allan Atkins allan.atkins@tmi-stl.com Outside Sales
Andrew Duckworth andrew.duckworth@tmi-kc.com Other
Brooks Easton brooks.easton@tmi-kc.com Other(Service Tech)
Cari Schroeder cari.schroeder@tmi-stl.com Other(Support)
Chad Netcalf Other(Employee)
Chris Dennis chris.dennis@tmi-asg.com Inside Sales
Christian Oliver christian.oliver@tmi-asg.com Inside Sales
CJ Hof cj.hof@tmi-kc.com Outside Sales
Cory Powell cory.powell@tmi-kc.com Other(Support)
Dan Scott dan.scott@tmi-wichita.com Other(Service Technician)
Darin Tipton darin.tipton@tmi-stl.com Inside Sales
Dave Rich dave.rich@tmi-stl.com Principal
Dave Talken dave.talken@tmi-kc.com Inside Sales
David Duckworth david.duckworth@tmi-kc.com Other(Support)
David Duckworth david.duckworth@tmi-kc.com Outside Sales
Doug Knipp doug.knipp@tmi-kc.com Outside Sales
drew garcia drew.garcia@tmi-kc.com Other(Service)
Fredrick Newell fred.newell@tmi-stl.com Outside Sales
Jason Hutchinson jason.hutchinson@tmi-stl.com Other
Jeff Kueper koop@tmi-asg.com Other(Parts Advisor)
Jen Holmes jen.holmes@tmi-asg.com Sales Support
Jim Root jim.root@tmi-kc.com Inside Sales
Jimmy Nguyen jimmy.lenguyen@tmi-kc.com Other(Service Technician)
John Clemmer john.clemmer@tmi-kc.com Inside Sales
John Quinly john.quinly@tmi-kc.com Inside Sales
Jonathan Pool jonathan.pool@tmi-kc.com Other(Service Sales Rep)
Joshua Bowlin josh.bowlin@tmi-kc.com Inside Sales
Karen Ewbank karen.ewbank@tmi-kc.com Admin
Keith Conaway keith.conaway@tmi-stl.com Connected Services
Keith Koudele keith.koudele@tmi-kc.com Outside Sales(Sr. Engineering Consultant)
Kevin Kaufman kevin.kaufman@tmi-kc.com Outside Sales
Kevyn Gordon kevyn.gordon@tmi-kc.com Outside Sales
Lee Dust lee.dust@tmi-kc.com Inside Sales
Lee Elliott unknown@unknown.com Other(Technician)
Mark Becker mark.becker@tmi-stl.com Inside Sales
Mark Sanders mark.sanders@tmi-kc.com Outside Sales
Marybeth Mueller marybeth.mueller@tmi-stl.com Sales Support
Matt Brewer matt.brewer@tmi-kc.com Outside Sales
Matt Costanzo matt.costanzo@tmi-kc.com Outside Sales
Matthew Stalling matt.stalling@tmi-kc.com Inside Sales
Max Carroll max.carroll@tmi-kc.com Outside Sales
Mel Macfarlane mel.macfarlane@tmi-kc.com Other(Service Tech)
Michael Caguin michael.caguin@tmi-stl.com Connected Services
Mike Basler mike.basler@tmi-stl.com Other(Service Tech)
Mike Fallon mike.fallon@tmi-stl.com CFO
Mike McPike mike.mcpike@tmi-kc.com Outside Sales
Renee Wagner renee.wagner@tmi-stl.com Admin
Robby Arthur robby.arthur@tmi-kc.com Other(Service)
Ryan Gibson ryan.gibson@tmi-stl.com Outside Sales
Sally Wind sally.wind@tmi-stl.com Other(Service Coordinator)
Steven Brewer steven.brewer@tmi-kc.com Outside Sales
Steven Dennis sdennis@havtech.com Outside Sales
Taylor Shepherd taylor.shepherd@tmi-kc.com Inside Sales(Sales Engineer)
Tim Weisner tim.weisner@tmi-stl.com Outside Sales
Tom Keller tom.keller@tmi-kc.com Inside Sales
Wayne Nenninger wayne.nenninger@tmi-stl.com Outside Sales
Wes Hueseman wes.hueseman@tmi-stl.com Sales Director
Daikin TMI LLC { St. Louis - 6920 }
Email: wes.hueseman@tmi-stl.com
Phone Number: (636) 532-1110
Mailing Address: 715 Goddard Avenue, Chesterfield, Missouri 63005 United States
Shipping Address: 715 Goddard Avenue, Chesterfield, Missouri 63005 United States
Name Email Title
Aaron Scherr aaron.scherr@tmi-stl.com Other(Service)
Alanna Ketchum alanna.ketchum@tmi-stl.com Sales Support
Alex Henricks alex.henricks@tmi-asg.com Other(Warehouse)
Allan Atkins allan.atkins@tmi-stl.com Outside Sales
Andrew Duckworth andrew.duckworth@tmi-kc.com Other
Angel Neuschwander angel.neuschwander@tmi-stl.com Inside Sales
Angelo Caraffa angelo.caraffa@tmi-stl.com Other(Service Technician)
Becky Collum becky.collum@tmi-stl.com Inside Sales
Becky Cullom becky.cullom@tmi-stl.com Other
Ben Buss ben.buss@tmi-stl.com Other(Support)
Bob Gunn bob.gunn@tmi-stl.com Inside Sales
Bobby Candee bobby.candee@tmi-stl.com Other(Support)
Brett Stoll brett.stoll@tmi-stl.com Outside Sales
Brooks Boeschen brooks.boeschen@tmi-asg.com Outside Sales
Bryan Reinhart bryan.reinhart@tmi-stl.com Outside Sales
Carey Edwards carey.edwards@daikinapplied.com Other
Cathy Brown cathy.brown@tmi-stl.com Other(Support)
Chad Wunsch chad.wunsch@tmi-stl.com Outside Sales
Chris Dennis chris.dennis@tmi-asg.com Inside Sales
Chris Swallow chris.swallow@tmi-stl.com Outside Sales
Christian Oliver christian.oliver@tmi-asg.com Inside Sales
CJ Hof cj.hof@tmi-kc.com Outside Sales
Cody Markotay cody.markotay@tmi-stl.com Other
Corey Maynard corey.maynard@tmi-stl.com Outside Sales
Craig Brandt craig.brandt@tmi-stl.com Outside Sales
Craig Rigden craig.rigden@tmi-asg.com Other
Dan Amsler dan.amsler@tmi-stl.com Inside Sales
Dan Ems Other
Dan Layton dan.layton@tmi-stl.com Inside Sales
Dan Noonan Other
Dan Scott dan.scott@tmi-wichita.com Other(Service Technician)
Daniel Rettenmaier dan.rettenmaier@tmi-stl.com Outside Sales
Darin Tipton darin.tipton@tmi-stl.com Inside Sales
Dave Rich dave.rich@tmi-stl.com Principal
Dave Talken dave.talken@tmi-kc.com Inside Sales
Dillon Brooks dillon.brooks@tmi-kc.com Other
Donna Andell donna.andell@tmi-stl.com Admin
Doug Knipp doug.knipp@tmi-wichita.com Other
Eddie Christ eddie.christ@tmi-stl.com Inside Sales
Erik Maldonado erik.maldonado@tmi-wichita.com Other
Erin Hibbits erin.hibbits@tmi-stl.com Inside Sales
Fredrick Newell fred.newell@tmi-stl.com Outside Sales
Garret Burns garret.burns@tmi-stl.com Other
Jake Henricks jake.henricks@tmi-asg.com Other
James Dymott james.dymott@tmi-stl.com Inside Sales
James Ertel jim.ertel@tmi-stl.com Outside Sales
Jason Boesch jason.boesch@taycon-tmi.com Other
Jason Fallon jason.fallon@tmi-stl.com Other(Service Technician)
Jason Vance jason.vance@tmi-stl.com Other
Jeff Escott jeff.escott@tmi-stl.com Outside Sales
Jeff Kueper koop@tmi-asg.com Other(Parts Advisor)
Jeffery Mayse jeff.mayse@tmi-asg.com Other(Parts)
Jim Fahrenhorst jim.fahrenhorst@tmi-stl.com Outside Sales
Jim Moore Other
Jim Noonan jim.noonan@tmi-stl.com Other
Jim Root jim.root@tmi-kc.com Inside Sales
Jim Salsman jim.salsman@tmi-stl.com Branch Manager
Jim Struck jim.struck@tmi-asg.com Other(Parts)
Joe Amsler joe.amsler@tmi-stl.com Inside Sales
Joe Ostermeyer joe.ostermeyer@tmi-stl.com Other(Service Technician)
John McVey Other
John Vogel john.vogelpohl@tmi-stl.com Other(Service)
Justin Sharpe justin.sharpe@tmi-stl.com Other(Service Tech)
Kayla Missey kayla.missey@tmi-stl.com Admin
Keith Conaway keith.conaway@tmi-stl.com Connected Services
Kelby Reinke kelby.reinke@tmi-kc.com Contracting Services
Ken Kalicak ken.kalicak@tmi-stl.com Outside Sales
Kevin Krimmel kevin.krimmel@tmi-stl.com GM/VP
Kevin O'Neill kevin.oneill@tmi-stl.com Outside Sales
Kimberley Mooney kimberley.mooney@tmi-stl.com Admin
Laine Brooks laineb@thermalmechanics.com Other
Levi Love levi.love@tmi-stl.com Other
Lew Feldcamp lewfeldkamp@gmail.com Other
Lew Feldkamp lew.feldkamp@tmi-stl.com Other
Lori Pederson lori.pederson@tmi-stl.com Admin
Lukas Weisner lukas.weisner@tmi-stl.com Other(Service)
Mark Ballard mark.ballard@tmi-stl.com Inside Sales
Mark Becker mark.becker@tmi-stl.com Inside Sales
Mark Cernelik noemail@needs.com Other
Mark Peters mark.peters@tmi-stl.com Inside Sales
Marybeth Mueller marybeth.mueller@tmi-stl.com Sales Support
Matt Dubois matt.dubois@tmi-stl.com Other(Technician - St. Louis)
Matt Johnson matt.johnson@tmi-stl.com Other(Service Tech)
Matthew Johnson matthew.johnson@tmi-stl.com Other(Support)
Michael Caguin michael.caguin@tmi-stl.com Connected Services
Michael Krispin mike.krispin@tmi-stl.com Other(Service)
Michael Maynard corey.maynard@tmi-stl.com Outside Sales
Mike Fallon mike.fallon@tmi-stl.com CFO
Mike Moses mike.moses@tmi-asg.com Other(Parts)
Mike Rich mike.rich@tmi-stl.com Outside Sales
Nathan Hoffmeister nathan.hoffmeister@tmi-stl.com Other(Service Tech)
Nick Hall nick.hall@tmi-stl.com Other
Pete Coulter pete.coulter@tmi-stl.com Other(Service)
Pete Minton pete.minton@taycon-tmi.com Principal
Renee Rulo renee.rulo@tmi-stl.com Admin
Renee Wagner renee.wagner@tmi-stl.com Admin
Rich Leadford rich.leadford@tmi-stl.com Other(Technician - St. Louis)
Rob Vorel rob.vorel@tmi-stl.com Outside Sales
Robert Whitehorn robert.whitehorn@tmi-stl.com Outside Sales
Ron Hubbard ron.hubbard@tmi-stl.com Inside Sales
Ron Oliver ron.oliver@tmi-asg.com Other(Parts)
Ryan Stewart ryan.stewart@tmi-stl.com Other(Service Tech)
Scott Thomas Other
Sean Hanlon sean.hanlon@tmi-stl.com Other(Service Tech)
Sierra Pryor sierra.pryor@tmi-stl.com Sales Support
Silla Ruckenbrod silla.ruckenbrod@tmi-stl.com Other(Technician)
Steve Guithues stephen.guithues@tmi-stl.com Other(Support)
Steven Puzach steve.puzach@tmi-stl.com Outside Sales
Tabitha Waldron tabitha.waldron@tmi-stl.com Inside Sales
Tim Weisner tim.weisner@tmi-stl.com Outside Sales
Tom Wolken tom.wolken@tmi-stl.com Other(Support)
Tony Harper tony.harper@tmi-stl.com Other(Service)
Tony Watring tony.watring@tmi-stl.com Inside Sales
Travis Oblein travis.oblein@tmi-stl.com Other(Service Technician)
Vicky Hammond vicky.hammond@tmi-stl.com Other(Financial)
Wayne Nenninger wayne.nenninger@tmi-stl.com Outside Sales
Wes Hueseman wes.hueseman@tmi-stl.com Sales Director
William (Jason) Hibbits jason.hibbits@tmi-stl.com Outside Sales
ElitAire, Inc. { Cincinnati - 6400 }
Email: rdewitt@elitaire.com
Phone Number: (513) 475-3800
Mailing Address: 4280 Glendale-Milford Rd, Blue Ash, Ohio 45242 United States
Shipping Address: 4280 Glendale-Milford Rd, Blue Ash, Ohio 45242 United States
Name Email Title
Adam Lewis alewis@elitaire.com Inside Sales
Alex Kalnasy akalnasy@elitaire.com Outside Sales
Assami Semde asemdi@elitaire.com Inside Sales
Austin Miller amiller@elitaire.com Other
Ben Arnett barnett@elitaire.com Outside Sales
Ben Releford breleford@elitaire.com Other(Technician)
Ben Smith bsmith@elitaire.com Other
Bill Noble bnoble@elitaire.com Other
Bill Schriner bschriner@elitaire.com Outside Sales
Blake Courtney bcourney@elitaire.com Inside Sales
Brandon Johnson bjohnson@elitaire.com Other
Brett Graham bgraham@elitaire.com Outside Sales
Brian Turner Other
Bryan Capozzoli bcapozzoli@emcor.net Other(Service Technician)
Carrie Haggard chaggard@elitaire.com Admin
Casey Topp caseytopp@elitaire.com Outside Sales
Chris Hall chall@elitaire.com Other(Account Executive)
Chris Weiss cweiss@elitaire.com Project Developer/Manager
Christian Holden cholden@elitaire.com GM/VP
Cody Fralick cfralick@elitaire.com Outside Sales
Colby Sleek csleek@elitaire.com Inside Sales
Cristian Garcia cgarcia@elitaire.com Sales Support
Dave Harper dharper@elitaire.com Other(Technician)
Dave Koors Other
David Finkbeiner dfinkbeiner@elitaire.com Other
Dylan Lott dlott@elitaire.com Inside Sales
Evan Nutt enutt@elitaire.com Outside Sales
Ezekiel Thompson ethompson@elitaire.com Other(Service Technician)
Ezra Vonnegut-Gbovitch ezravg@elitaire.com Principal
Hassan Alhashim halhashim@elitaire.com Sales Support
Jared Rering jrering@elitaire.com Inside Sales
JC Haggard jhaggard@elitaire.com Other(Service Technician)
Jeff Dollar jdollar@elitaire.com Outside Sales
Jim Shopshire jshopshire@elitaire.com Other(Journeyman)
Jim Tierney jtierney@elitaire.com Inside Sales
John Engelkamp jengelkamp@elitaire.com Estimator
Josh Bolin jbolin@elitaire.com Outside Sales
Keith Greene kgreene@elitaire.com Estimator
Kyle Somner Other
Mary Wilking mwilking@elitaire.com Admin
Max Rouse mrouse@elitaire.com Sales Support
Michael Peters mpeters@elitaire.com Other(Technician)
Michael Weisman mweisman@elitaire.com Outside Sales
mike baker Other
Mike Kirchens mkirchens@elitaire.com Other
Mike Kirchens mkirchens@elitaire.com Outside Sales
Mike Wiseman mwiseman@elitaire.com Other(Sales Engineer)
Myia Holden mholden@elitaire.com Sales Support
Nash Baldwin nbaldwin@elitaire.com Controls
Nathan Jones njones@elitaire.com Other(Technician)
Pat Fischer pfischer@elitaire.com Inside Sales
Richard McDermitt richard.mcdermitt@cbsiohio.com Other
Rick DeWitt rdewitt@elitaire.com GM/VP
Ryan Halvorsen rhalvorsen@elitaire.com Outside Sales
Sarah Owen sowen@elitaire.com Other(Finance)
Scott Folzenlogen folzenlogen@elitaire.com Controls
Scott Gregor sgreger@elitaire.com Sales Support
Stephanie Myers smyers@elitaire.com Estimator
Tom Haun thaun@elitaire.com Outside Sales
Tom Martini Other
Travis Wickham twickham@elitaire.com Other(Service)
Troy Reeder treeder@elitaire.com Other(Principal-Account Executive)
ElitAire, Inc. { Columbus - 6410 }
Email: mbeecroft@elitaire.com
Phone Number: (614) 360-1330
Mailing Address: 6155-A Huntley Road, Columbus, Ohio 43229 United States
Shipping Address: 6155-A Huntley Road, Columbus, Ohio 43229 United States
Name Email Title
Allan Gartner agartner@elitaire.com Sales Support
Austin Miller amiller@elitaire.com Other
Casey Kapustka ckapustka@elitaire.com Outside Sales
Christian Holden cholden@elitaire.com GM/VP
Connor Beecroft cbeecroft@elitaire.com Outside Sales
Craig Stephens cstephens@elitaire.com Outside Sales
Derek Fryfogle dfryfogle@elitaire.com Outside Sales
Dustin McFarland dmcfarland@elitaire.com Sales Support
Jason Miller Other
Jason Nutbrown jnutbrown@elitaire.com Project Developer/Manager
Jason Schriner jschriner@elitaire.com Outside Sales
Justin Andrix jandrix@elitaire.com Other(Service Technician)
Karen Lince klince@elitaire.com Admin
Karen Smith ksmith@elitaire.com Project Developer/Manager
Kenneth Schlaegel kschlaegel@elitaire.com Principal
Mark Ganser mganser@elitaire.com Outside Sales
Matt Beecroft mbeecroft@elitaire.com GM/VP
Michael Peters mpeters@elitaire.com Other(Technician)
Nick McCord nmccord@elitaire.com Other(Technician)
Robert Miley rmiley@elitaire.com Inside Sales
Ryan Valenta rvalenta@elitaire.com Outside Sales
Seth Pearch spearch@elitaire.com Outside Sales
Tony Decrescenzo tdecrescenzo@elitaire.com Outside Sales
Trey Schroeder tschroeder@elitaire.com Other(Service Technician)
EMCO Corporation { New Brunswick - 4220 }
Email: kedgecombe@emcoltd.com
Phone Number: (506) 853-1440
Mailing Address: 136 English Drive, Moncton, New Brunswick E1E 4G7 Canada
Shipping Address: 136 English Drive, Moncton, New Brunswick E1E 4G7 Canada
Name Email Title
Anton Wolmarans awolmarans@emcoltd.com Outside Sales(Outside Sales)
Cameron Brioux cbrioux@emcoltd.com Outside Sales
Kristine Girard kgirard@emcoltd.com Inside Sales
Mathieu Ouellet mouellet@emcoltd.com Principal
Nikos Doiron ndoiron@emcoltd.com Inside Sales
Rudy Walters rwalters@emcoltd.com Sales Support
EMCO Corporation { Nova Scotia - 4210 }
Email: dferrera@emcoltd.com
Phone Number: (902) 468-9911
Mailing Address: P.O. Box 5300, Stn A, London, Ontario N6A 4N7 Canada
Shipping Address: 45 Borden Avenue,Unit 4, Dartmouth, Nova Scotia B3B 1C7 Canada
Name Email Title
Andrew Lewis alewis@emcoltd.com Other(Counter Sales)
Andrew MacEwen amacewen@emcoltd.com Inside Sales
Beth Munro bmunro@emcoltd.com Admin
Brent Squires brsquires@emcoltd.com Inside Sales
Brian Zhu bzhu@emcoltd.com Other(Project Engineer)
Chris Conrad cconrad@emcoltd.com Other(IT)
Claudette Roy croy@emcoltd.com Other(Technical Specialist)
David Innes dinnes@emcoltd.com Outside Sales
Dylan Doucette ddoucette@emcoltd.com Inside Sales
Dylan MacKenzie dmackenzie@emcoltd.com Sales Support
Emmanuel Agana eagana@emcoltd.com Sales Support
James Venieris jvenieris@emcoltd.com Other
Jeremy Burke jburke@emcoltd.com Inside Sales
Kelsey Edgecombe kedgecombe@emcoltd.com Outside Sales
Maria Skrigolovskaya marias@emcoltd.com Outside Sales
Mathieu Ouellet mouellet@emcoltd.com Principal
Mohamed Kasmani mkasmani@emcoltd.com Inside Sales
Naufil Sayed nsayed@emcoltd.com Outside Sales
Randy Smith rsmith@emcoltd.com Sales Support
Sean Breen sbreen@emcoltd.com Project Developer/Manager
Steve Croft scroft@emcoltd.com Outside Sales
Trevor MacDonald tmacdonald@emcoltd.com Principal
Willem Paynter wpaynter@emcoltd.com Principal
Yassir Subratty ysubratty@emcoltd.com Inside Sales
Zach Williams zwilliams@dkemcor.com Other
EMCO Corporation { Prince Edward Island - 4230 }
Email: tmacdonald@emcoltd.com
Phone Number: (902) 894-8870
Mailing Address: P.O. Box 5300, Stn A, London, Ontario N6A 4N7 Canada
Shipping Address: 7 Walker Drive, Unit C, Charlottetown, Prince Edward Island C1A 8S5 Canada
Name Email Title
Andrew MacEwen amacewen@emcoltd.com Inside Sales
Chris Conrad cconrad@emcoltd.com Other(IT)
Claudette Roy croy@emcoltd.com Other(Technical Specialist)
Dylan MacKenzie dmackenzie@emcoltd.com Sales Support
Trevor MacDonald tmacdonald@emcoltd.com Principal
Ewing/Kessler Mechanical Solutions, Inc. { Jackson - 2070 }
Email: fkessler@ewingkessler.com
Phone Number: (601) 982-0044
Mailing Address: 1919 Lakeland Drive,Suite B, Jackson, Mississippi 39205 United States
Shipping Address: 1919 Lakeland Drive,Suite B, Jackson, Mississippi 39205 United States
Name Email Title
Chad Albin calbin@ewingkessler.com Outside Sales
Chris Ewing cewing@ewingkessler.com Principal
Frank Kessler fkessler@ewingkessler.com Principal
Jack Brister jbrister@ewingkessler.com Inside Sales
Jane Brown jbrown@ewingkessler.com Other(Project Manager)
Kimberly Jeffares kjeffares@ewingkessler.com Inside Sales
Kyle Upton kupton@ewingkessler.com Outside Sales
Michael Walker mwalker@ewingkessler.com Inside Sales
Mike Carroll mcarroll@ewingkessler.com Outside Sales
Mike Walker Other
Punch Chotivittayathanin punch@ewingkessler.com Sales Director
Race Stewart rstewart@ewingkessler.com Inside Sales
Robert Thomas rthomas@ewingkessler.com Outside Sales
Thomas Price tprice@ewingkessler.com Project Developer/Manager
Ewing/Kessler Mechanical Solutions, Inc. { Memphis - 2030 }
Email: sales@ewingkessler.com
Phone Number: (901) 654-2400
Mailing Address: 1631 Century Center Parkway,Suite 105, Memphis, Tennessee 38134 United States
Shipping Address: 1631 Century Center Parkway,Suite 105, Memphis, Tennessee 38134 United States
Name Email Title
Arjun Muratee amuratee@ewingkessler.com Other(Accounting Clerk)
Brett Harpel bharpel@ewingkessler.com Other(Service)
Brian Washburn bwashburn@ewingkessler.com Other(Service)
Carl Christian cchristian@ekautomation.com Other
Chad Albin calbin@ewingkessler.com Outside Sales
Chris Ewing cewing@ewingkessler.com Principal
Corey Brewer cbrewer2@ewingkessler.com Other(Service)
Cyrus Booker cbooker@ewingkessler.com Outside Sales
Dan Seymour Other
Frank Kessler fkessler@ewingkessler.com GM/VP
Frank Kessler fkessler@ewingkessler.com Principal
Jack Blurton jblurton@ewingkessler.com Other
Jane Brown jbrown@ewingkessler.com Other(Project Manager)
Jeremy Williams jwilliams@ewingkessler.com Other
Jerry Edwards jedwards@ekautomation.com Outside Sales
Jim Riendeau jriendeau@ewingkessler.com Principal
Jimmy Ricks jricks@ewingkessler.com Other(Service Technician)
Joel Coleman jcoleman@ewingkessler.com Inside Sales
John Patterson jpatterson@ewingkessler.com Inside Sales
John Seymour jseymour@ekautomation.com Other
Jonathan Lancaster jlancaster@ewingkessler.com Outside Sales
Jonathon Lancaster jlancaster@ewingkessler.com Other(Solutions Engineer)
Lorri Cox lcox@ewingkessler.com Other(Executive Assistant)
Mark Johnson Other
Mark Lafhameyer mlafhameyer@ewingkessler.com Other(Systems Administrator)
Mark Watkins mwatkins@ewingkessler.com Principal
Matthew Huddleston mhuddleston@ewingkessler.com Inside Sales
Matthew Sanders msanders@ewingkessler.com Outside Sales
Michael Walker mwalker@ewingkessler.com Inside Sales
Mike Carroll mcarroll@ewingkessler.com Outside Sales
Mike Slattery mslattery@ewingkessler.com Outside Sales
Rob Thomas rthomas@ewingkessler.com Outside Sales
Stacie Sing ssing@ewingkessler.com Controls
Susan Casteel scasteel@ewingkessler.com Other(Financial)
Thad Gump Other(Service Tech)
Thomas Price tprice@ewingkessler.com Project Developer/Manager
Gardiner { Akron - 2300 }
Email: mowens@whgardiner.com
Phone Number: (330) 896-9358
Mailing Address: 1530 Corporate Woods Parkway,Suite 200, Uniontown, Ohio 44685 United States
Shipping Address: 1530 Corporate Woods Parkway,Suite 200, Uniontown, Ohio 44685 United States
Name Email Title
Brian Wild bwild@whgardiner.com Outside Sales
David Adler dadler@whgardiner.com Outside Sales
Josh Vermillion jvermillion@whgardiner.com Outside Sales
JP Genova jpgenova@whgardiner.com Inside Sales
Lori Lawton llawton@whgardiner.com Sales Support
Gardiner { Cleveland - 2280 }
Email: mowens@whgardiner.com
Phone Number: (440) 248-3400
Mailing Address: 31300 Bainbridge Road, Solon, Ohio 44139 United States
Shipping Address: 31300 Bainbridge Road, Solon, Ohio 44139 United States
Name Email Title
Aiden Winkhart awinkhart@whgardiner.com Inside Sales
Allan Dynes adynes@whgardiner.com Admin
Amariyah Yisrael ayisrael@whgardiner.com Inside Sales
Amy Cadwallader acadwallader@whgardiner.com Inside Sales
Amy Golson agolson@whgardiner.com Inside Sales
Andy English aenglish@whgardiner.com Outside Sales
Austin Miller amiller@whgardiner.com Other
Barb Trusnik btrusnik@whgardiner.com Sales Support
Benny Montomery bmontgomery@whgardiner.com Other(Service Technician)
Chip Polivka cpolivka@whgardiner.com Outside Sales
Christina Tomola ctomola@whgardiner.com Inside Sales
Christopher Sanafelt cshanafelt@whgardiner.com Other(Service)
Dan Babic dbabic@whgardiner.com Other(Sales Manager)
Daniel Nish dnish@whgardiner.com Sales Director
Dave Smith dsmith@whgardiner.com Outside Sales
David Weber dweber@whgardiner.com Other(Service)
Debbie Brun drun@whgardiner.com Inside Sales
Del Turnbull dturnbull@whgardiner.com Inside Sales
Don Sabetta dsabetta@whgardiner.com Controls
Dustan Byler dbyler@whgardiner.com Other(Service)
Harry Hakenson hhakenson@whgardiner.com Inside Sales
Jacob Fugate jfugate@whgardiner.com Other
Jared Prior jprior@whgardiner.com Inside Sales
Jennifer Hoobler jhoobler@whgardiner.com Inside Sales
John McCoy jmccoy@whgardiner.com Inside Sales
Joseph Merolla jmerolla@whgardiner.com Controls
Justin Malave jmalave@whgardiner.com Inside Sales
Karen Lerchbacher klerchbacher@whgardiner.com Inside Sales
Kayla Franczak kfranczak@whgardiner.com Other(MARKETING)
Keith Karbine kkarbine@whgardiner.com Other(Service Technician)
Kirk Eichelberger keichelberger@whgardiner.com Outside Sales
Kirk L. Eichelberger parts@whgardiner.com Other
Kyle Herbst kherbst@whgardiner.com Other
Kyle Ritchie kritchie@whgardiner.com Outside Sales
Lee Frazer lfrazer@whgardiner.com Inside Sales
Malcolm Jamison mjamison@whgardiner.com Outside Sales
Malcom Jamison mjamison@whgardiner.com Outside Sales
Marin Musser mmusser@whgardiner.com Outside Sales
Melissa Turnbull Other
Michael Hendicks mhendricks@whgardiner.com Other(DESIGN ENGINEER)
Michael McMichael mmcmichael@whgardiner.com Principal
Michael Morehouse mmorehouse@whgardiner.com Estimator
Michael Reindel mreindel@whgardiner.com Other(Service)
Mike Ball mball@whgardiner.com Outside Sales
Mike Pratt mpratt@whgardiner.com Other
Mike Toppings mtoppings@whgardiner.com Controls
Nick Oriani noriani@whgardiner.com Other(ANALYTICS)
Nikola Cekic ncekic@whgardiner.com Other
Noelle Lipkowski nlipkowski@whgardiner.com Admin
Paige Hagedorn phagedorn@whgardiner.com Other
Paul Krosse pkrosse@whgardiner.com Inside Sales
Raven Hazlett rhazlett@whgardiner.com Inside Sales
Rebecca Harris rharris@whgardiner.com Other(CONTROLLER)
Rob MacKinlay rmackinlay@whgardiner.com CFO
Rob Rein rrein@whgardiner.com Other
Robert Ambrose rambrose@whgardiner.com Outside Sales
Robert McClintock rmcclintock@whgardiner.com Outside Sales
Robert Penix rpenix@whgardiner.com Estimator
Robert Segovia rsegovia@whgardiner.com Outside Sales
Ryan Manhard rmanhard@whgardiner.com Other(Service Technician)
Samuel Dietrich sdietrich@whgardiner.com Outside Sales
Samuel Turner seturner@whgardiner.com Other(Service)
Scot Turner sturner@whgardiner.com Other(Service)
Scott Sutton ssutton@whgardiner.com Outside Sales
Scott West swest@whgardiner.com Other(Technician)
Sequoyah Russell srussell@whgardiner.com Other(Service Technician)
Service Purchasing servicepurchasing@whgardiner.com Contracting Services
Sharon Dorn sdorn@whgardiner.com Sales Support
Steve Mathews smathews@whgardiner.com Other(PURHCASING DIRECTOR)
Thomas Whitehead twhitehead@whgardiner.com Outside Sales
Tim Lewis tlewis@whgardiner.com Other(Service Technician)
Tina Dunikowski tdunikowski@whgardiner.com Inside Sales
Todd Barnhart tbarnhart@whgardiner.com Principal
Tyler Grabowski tgrabowski@whgardiner.com Outside Sales
William Postlethwait wpostlethwait@whgardiner.com Other(Service)
Gardiner { Toledo - 2290 }
Email: mowens@whgardiner.com
Phone Number: (419) 794-3400
Mailing Address: 4444 Keystone Drive,Suite H, Maumee, Ohio 43537 United States
Shipping Address: 4444 Keystone Drive,Suite H, Maumee, Ohio 43537 United States
Name Email Title
Alyan Memon amemon@whgardiner.com Outside Sales
David Cowley dcowley@whgardiner.com Outside Sales
Ernie Dieball edieball@whgardiner.com Outside Sales
Jeff Coleman jkunkelman@whgardiner.com Other
Kimberly Joshaway kjoshaway@whgardiner.com Office Manager
Kristin Keeney kkeeney@whgardiner.com Other
Nathan Heffner nheffner@whgardiner.com Outside Sales
Patrick Meehan pmeehan@whgardiner.com Outside Sales
Rob Segovia rsegovia@whgardiner.com Outside Sales
Todd Barnhart tbarnhart@whgardiner.com Principal
Global Mechanical Sys. Ltd { Moncton - 1680 }
Email: gary@globalmech.com
Phone Number: (506) 857-4887
Mailing Address: 290 Baig Blvd, Unit B1, Moncton, New Brunswick E1E 1C8 Canada
Shipping Address: 290 Baig Blvd, Unit B1, Moncton, New Brunswick E1E 1C8 Canada
Name Email Title
Bob Chapot Other
Debbie Currie debbie@globalmech.com Other
Jarrett Green jarrett@globalmech.com Other
Robert Dugas robert@globalmech.com Other
Global Price Mechanical { Nova Scotia - 1660 }
Email: gary@globalmech.com
Phone Number: (902) 443-1114
Mailing Address: 60 Dorey Avenue,Suite 102, Dartmouth, Nova Scotia B3B 0B1 Canada
Shipping Address: 60 Dorey Avenue,Suite 102, Dartmouth, Nova Scotia B3B 0B1 Canada
Name Email Title
Doug Allen doug@globalpricemech.com Other
H.V.A.C. Sales (1997) Ltd. { Regina - 3140 }
Email: brent@skhvac.com
Phone Number: (306) 721-7980
Mailing Address: 606A Solomon Crescent, Regina, Saskatchewan S4N 4N7 Canada
Shipping Address: 606A Solomon Crescent, Regina, Saskatchewan S4N 4N7 Canada
Name Email Title
Blake Erb blake@skhvac.com Outside Sales
Brent Smith brent@skhvac.com Principal
Carlene Grant carlene@skhvac.com Admin
Chad Kuski chad@skhvac.com Outside Sales
Colin Hilderman colin@skhvac.com Outside Sales
Derek Fuchs derek@skhvac.com Outside Sales
Devan Kincart devan@skhvac.com Inside Sales
Eric Gregg eric@skhvac.com Outside Sales
Forrest Smith forrest@skhvac.com GM/VP
Kailley Holmes kailley@skhvac.com Inside Sales
Kim Morse kim@skhvac.com Outside Sales
Larry Hahn larry@skhvac.com Other
Lorelei Smith lorelei@skhvac.com Admin
Maury Wawryk maury@skhvac.com GM/VP
Richard Skopyk richard@skhvac.com Other(aftermarket sales)
Robert Smith robert.smith@daikinapplied.com Principal
Shane Wilkes shane@skhvac.com Other(Sales)
Stefan Belev stefan@skhvac.com Outside Sales
Terry Seidlitzed terry@skhvac.com Other
Wade Fuchs wade@skhvac.com Outside Sales
Harrison Energy Partners { Little Rock - 2770 }
Email: sales@harrisonenergy.com
Phone Number: (501) 661-0621
Mailing Address: 1501 Westpark Drive,Suite 9, Little Rock, Arkansas 72204 United States
Shipping Address: 1501 Westpark Drive,Suite 9, Little Rock, Arkansas 72204 United States
Name Email Title
Adam Frankenberger afrankenberger@harrisonenergy.com Inside Sales
Amanda Ingle aingle@harrisonenergy.com Admin
Benjamin Friesen bfriesen@harrisonenegy.com Other(Service)
Bill Harrison bharrison@harrisonenergy.com Other(CEO)
Bill Simpson bsimpson@harrisonenergy.com Other(Sales Engineer)
Bill Simpson bsimpson@harrisonenergy.com Sales Director
Brett Bolan bbolan@harrisonenergy.com Principal(IT Director)
Brian Swindle bswindle@harrisonenergy.com CFO
Brynn Lea blea@harrisonenergy.com Outside Sales
Coby Sutton csutton@harrisonenergy.com Sales Director
Connie Hawley chawley@harrisonenergy.com Admin
Dana Foster dfoster@harrisonenergy.com Other(Financial)
Daniel Nehus dnehus@harrisonenergy.com Outside Sales
Denton King dking@harrisonenergy.com Outside Sales
Gene Johnson gjohnson@harrisonenergy.com Other
Greg Blair gblair@harrisonenergy.com GM/VP(VP of Sales & Marketing)
Hunter Kidd hkidd@harrisonenergy.com Other(Financial Officer)
Jack Portale jportale@harrisonenergy.com Other(NSS)
Jacob Caudle jcaudle@harrisonenergy.com Other(Service)
Jake Skinner jskinner@harrisonenergy.com Outside Sales
Jeff Redman jredmond@harrisonenergy.com Other
Jim Bradford jbradford@harrisonenergy.com Inside Sales
Josh Ringgold jringgold@harrisonenergy.com Other
Josh Robinson jrobinson@harrisonenergy.com Outside Sales
Karen Edelmann kedelmann@harrisonenergy.com Other(Resource Coordinator)
Kelly Imhoff kimhoff@harrisonenergy.com Office Manager
Kerry Jones kjones@harrisonenergy.com Inside Sales
Maggie Majors mmajors@harrisonenergy.com Admin
Mark Raabe mraabe@harrisonenergy.com Inside Sales
Matt Brown mbrown@harrisonenergy.com Other(Service Technician)
Matt Nosler mnosler@harrisonenergy.com Other
Melissa Whitfield mwhitfield@harrisonenergy.com Other(Accounting Assistant)
Mike McClellan mmcclellan@harrisonenergy.com Principal
Morgan Clark mclark@harrisonenergy.com Inside Sales
Rachel Willard rwillard@harrisonenergy.com Other(Senior Technology Support Specialist)
Ronald Holt rholt@harrisonenergy.com Inside Sales
Sam Browning sbrowning@harrisonenergy.com Outside Sales
Samantha Sparks ssparks@harrisonenergy.com Other(HR Assistant)
Shaun Penny spenny@harrisonenergy.com Other(account executive)
Stephen Davis sdavis@harrisonenergy.com Inside Sales
Sydney Cartwright scartwright@harrisonenergy.com Outside Sales
Tammy Hatfield thatfield@harrisonenergy.com Inside Sales
Todd Castleberry tcastleberry@harrisonenergy.com Inside Sales
Tufail Muhammad tmuhammad@harrisonenergy.com Inside Sales
Walt Brewczynski wbrewczynski@harrisonenergy.com Other(Service Technician)
Harrison Energy Partners { Oklahoma City - 2810 }
Email: sales@harrisonenergy.com
Phone Number: (405) 658-8376
Mailing Address: 3100 North Sante Fe, Oklahoma City, Oklahoma 73118 United States
Shipping Address: 3100 North Sante Fe, Oklahoma City, Oklahoma 73118 United States
Name Email Title
Ben Dye bdye@harrisonenergy.com GM/VP(VP of Oklahoma)
Blake Dismuke bdismuke@harrisonenergy.com Other(Service)
Brian Swindle bswindle@harrisonenergy.com CFO
Chase Hundley chundley@harrisonenergy.com Outside Sales
Edie Fielder efielder@harrisonenergy.com Inside Sales
Greg Blair gblair@harrisonenergy.com GM/VP(VP of Sales & Marketing)
Jason Barry jbarry@harrisonenergy.com Outside Sales
Justin Mueller jmueller@harrisonenergy.com Inside Sales
Keaton Mullenix kmullenix@harrisonenergy.com Outside Sales
Larwetta McGee lmcgee@harrisonenergy.com Branch Manager(Resource Coordinator)
Luis Brito lbrito@harrisonenergy.com Outside Sales
Martin Sheared msheared@harrisonenergy.com Inside Sales
Michael Reese michael.reese1982@gmail.com Other(Service Technician)
Mike McClellan mmcclellan@harrisonenergy.com Principal
Teasi Graham tgraham@harrisonenergy.com Outside Sales
Walter Pendleton wpendleton@harrisonenergy.com Outside Sales
Harrison Energy Partners { Springdale - 2780 }
Email: sales@harrisonenergy.com
Phone Number: (479) 361-2030
Mailing Address: 2499 South Maestri Road, Springdale, Arkansas 72762 United States
Shipping Address: 2499 South Maestri Road, Springdale, Arkansas 72762 United States
Name Email Title
Brandon Moore bmoore@harrisonenergy.com Inside Sales
Brian Swindle bswindle@harrisonenergy.com CFO
David Carroll dcarroll@harrisonenergy.com Other
David Layman dlayman@harrisonenergy.com Other(Service)
Eric Pedersen epedersen@harrisonenergy.com Inside Sales
Greg Blair gblair@harrisonenergy.com GM/VP(VP of Sales & Marketing)
Just Blair jblair2@harrisonenergy.com Inside Sales
Keith Knight kknight@harrisonenergy.com Outside Sales
Kelly Gunlock kgunlock@harrisonenergy.com Outside Sales
Lee Wilson lwilson@harrisonenergy.com Other(Controls Sales)
Maridan Soderquist msoderquist@harrisonenergy.com Inside Sales
Michael Reese mreese@harrisonenergy.com Other
Payton Riddle priddle@harrisonenergy.com Inside Sales
Steve Huntington shuntington@harrisonenergy.com Inside Sales
Zachary Zitzmann zzitzmann@harrisonenergy.com Outside Sales
Harrison Energy Partners { Tulsa - 2790 }
Email: sales@harrisonenergy.com
Phone Number: (918) 619-5898
Mailing Address: 11414 East 51st Street,Suite A, Tulsa, Oklahoma 74146 United States
Shipping Address: 11414 East 51st Street,Suite A, Tulsa, Oklahoma 74146 United States
Name Email Title
Alan Spielman aspielman@harrisonenergy.com Inside Sales
Ben Dye bdye@harrisonenergy.com GM/VP(VP of Oklahoma)
Benjamin Biggs bbiggs@harrisonenergy.com Inside Sales
Brad Jolly bjolly@harrisonenergy.com Inside Sales
Cindy Hammons chammons@harrisonenergy.com Other(Resource Coordinator)
Darren Andersen dandersen@harrisonenergy.com Outside Sales
David Parker dparker@harrisonenergy.com Other(Service Technician)
David Weikel jh70882003@yahoo.com Other(Apprentice)
Greg Blair gblair@harrisonenergy.com GM/VP(VP of Sales & Marketing)
Jason Blair jblair@harrisonenergy.com Outside Sales
Jeremy Clifford jclifford@harrisonenergy.com Outside Sales
Lloyd Gaither lgaither@harrisonenergy.com Other(Service)
Matt Mieir mmieir@harrisonenergy.com Outside Sales
Phillip Butler pbutler@harrisonenergy.com Outside Sales
Richard Branham rbranham@harrisonenergy.com Outside Sales
Ryan Milam rmilam@harrisonenergy.com Other(Journeyman)
Susan Crenshaw screnshaw@harrisonenergy.com Other(Sales Engineer and Energy Manager)
Telisa Richardson trichardson@harrisonenergy.com Inside Sales
Terry Thomas tthomas@harrisonenergy.com Other(Oklahoma Field Service Supervisor)
Troy Eubanks teubanks@harrisonenergy.com Other(Service Technician)
Havtech { Balt. - 2920 }
Email: marketing@havtech.com
Phone Number: (410) 724-3703
Mailing Address: 9505 Berger Road, Columbia, Maryland 21046 United States
Shipping Address: 9505 Berger Road, Columbia, Maryland 21046 United States
Name Email Title
Adam Becker abecker@havtech.com Inside Sales
Addison Clark aclark@havtech.com Inside Sales
Albert Ouellette aouellette@havtech.com Other(Service Technician)
Alex Mao amao@havtech.com Inside Sales
Allen Reiner areiner@havtech.com Other(Service Technician)
Andrew Hartman andrewhartman@havtech.com Outside Sales
Andrew Latchman alatchman@havtech.com Inside Sales
Andrew Neal andrewneal@havtech.com Estimator
Andrew Reinhart areinhart@havtech.com Other
Andrew Saylor asaylor@havtech.com Inside Sales
Andriss Jourdan ajourdan@havtech.com Inside Sales
Anthony Jones anthonyjones@havtech.com Other(Sales Engineer)
Bailey LeConte bleconte@havtech.com Inside Sales
Bill Litz blitz@havtech.com Outside Sales
Bonnie Smith bsmith@havtech.com Other
Brady Schulz bschulz@havtech.com Other(System Application Engineer)
Brian Mitchell bmitchell@havtech.com Inside Sales
Brittany Nixon bnixon@havtech.com Inside Sales
Bryanne Marks bmarks@havtech.com Other(Financial)
Charles Bartlett cbartlett@havtech.com Branch Manager
Charles Brown cbrown@thermalhvac.com Outside Sales
Chris Eckenrode chriseckenrode@havtech.com Other(Financial)
Chrissy Oshields coshields@havtech.com Inside Sales
Christian Drumm cdrumm@havtech.com Inside Sales
Christopher Zimmerman czimmerman@havtech.com Inside Sales
DaMont Wood dwood@havtech.com Inside Sales
Dan May danmay@havtech.com Outside Sales
Dan Toombs Other
Darryl Hockstra dhockstra@havtech.com Outside Sales
Dave Doughty davedoughty@havtech.com Other(Sales Manager)
David Cunningham davidcunningham@havtech.com Outside Sales
David Eberhardt deberhardt@havtech.com Principal
David Robey drobey@havtech.com Other(Service Technician)
Delaney May delaneymay@havtech.com Inside Sales
Dennis Llaneza dllaneza@havtech.com Inside Sales
Donnell Avery davery@havtech.com Inside Sales
Doug Hunter dhunter@havtech.com Inside Sales
Eddie Neal eneal@havtech.com Sales Support
Eli Wilcox ewilcox@havtech.com Inside Sales
Elizabeth Hollon lhollon@havtech.com Inside Sales
Eric Cooley ecooley@havtech.com Other(Service Technician)
Eric Simpson esimpson@havtech.com Outside Sales
Erik Hess ehess@havtech.com Principal
Erin Cousler ecousler@havtech.com Other(Marketing Director)
Erin Moore emoore@havtech.com Outside Sales
Francine Brant francinebrant@havtech.com Inside Sales
Guy Bell gbell@havtech.com Inside Sales
Henry Adams hadams@havtech.com Inside Sales
Izat Majlaton imajlaton@havtech.com Inside Sales
Jack Murphy jmurphy@havtech.com Inside Sales
Jacob Gaines jgaines@havtech.com Other
Jamaal Holmes jamaal72@icloud.com Other(Service)
Jason Coppola jason@networkdepot.com Other(IT - Network Depot)
Jeffrey Cox jeffcox@havtech.com Principal
Jennifer Jenkins jenniferjenkins@havtech.com Principal
Jennifer Lomangino jlomangino@havtech.com Inside Sales
Jessica Burns jburns@havtech.com Inside Sales
Jim Randolph jimrandolph@havtech.com Other(Sales Engineer)
Jodi Bogue jodibogue@havtech.com Project Developer/Manager
Joe Roetering jroetering@thermalhvac.com Principal
Jonathan Lewis jlewis@havtech.com Outside Sales
Kathleen DeLeonibus kdeleonibus@havtech.com Inside Sales
Kayla Ryon kryon@havtech.com Inside Sales
Keaton Pavier keatonpavier@havtech.com Inside Sales
Keith Hugey hugheyees@yahoo.com Other
Kevin Stroop kstroop@havtech.com Outside Sales
Kim Davis-Garduno kdavisgarduno@havtech.com Inside Sales
Kurt Prager kprager@havtech.com Other(It Manager)
Larry Manross larrymanross@havtech.com Other(Sales Engineer)
Larry Mell lmell@havtech.com Principal
Lauren Peck lpeck@havtech.com Inside Sales
Leif Kennedy leifkennedy@havtech.com Outside Sales
Lia Valdesuso lvaldesuso@havtech.com Inside Sales
Logan Stanley lstanley@havtech.com Inside Sales
Maggie Whitesel mwhitesel@havtech.com Inside Sales
Mason Clairmont mclairmont@havtech.com Outside Sales
Matthew Ruby matthewruby@havtech.com Other(Application Engineer)
Mike Cruz mcruz@havtech.com Outside Sales
Mike Ruby mikeruby@havtech.com Other(Sales Engineer)
Miles Kline mkline@havtech.com Inside Sales
Nicholas Mirto nmirto@havtech.com Inside Sales
Nick Coleman ncoleman@havtech.com Inside Sales
Nicolas Wallace nwallace@havtech.com Other(Service Technician)
Nicole Holtz nholtz@havtech.com Inside Sales
Patrick Murdock patrickm@aceshvac.com Other(Equipment Sales Manager)
Paul Hoover paulhoover@havtech.com Other(Sr. Application Engineer)
Peter N/A Other
Rebekkah Parson rparson@havtech.com Inside Sales
Richard Aquino richaquino@havtech.com Other(Contracting Opertions Leader)
Rick Hays rhays@havtech.com Other(Field Supervison)
Rick Shafer rshafer@havtech.com GM/VP
Riley Fash rfahs@havtech.com Inside Sales
Robert Bliss rbliss@havtech.com Inside Sales
Robert Chaney rchaney@havtech.com Other(Field Service Engineer)
Robert Sisco rsisco@havtech.com Other(Field Service Engineer)
Rod Hollenberger rodhollenberger@havtech.com Other(Sales Engineer)
Scott Houghton shoughton@havtech.com Outside Sales
Scott Pierson spierson@havtech.com Other(Parts Business Leader)
Sean Kerns skerns@havech.com Other(Technician)
Sophia Guilday sguilday@havtech.com Inside Sales
Stafford Camp ccamp@havtech.com Inside Sales
Stephanie Holden stephanieholden@havtech.com Inside Sales
Stephanie Wilson stephaniewilson@havtech.com Inside Sales
Stephen Allen sallen@havtech.com Inside Sales
Steven Dennis sdennis@havtech.com Outside Sales
Steven Park spark@havtech.com Inside Sales
Terence Barnett tbarnett@havtech.com Outside Sales
Thor Fraser thorfraser@havtech.com Other(Sales Engineer)
Tim Carter tcarter@havtech.com Inside Sales
Tony Giampietro tgiampietro@havtech.com Inside Sales
Trey Goulden treygoulden@havtech.com Outside Sales(Aftermarket Outside Sales)
Tyler Moltz tmoltz@havtech.com Inside Sales
Vinny DiSalvo vdisalvo@havtech.com Outside Sales
Virginia DAquila virginiadaquila@havtech.com Project Developer/Manager
Wade Thies wadethies@havtech.com Outside Sales
Weston Gearhart wgearhart@havtech.com Outside Sales
William Holtzman wholtzman@havtech.com Inside Sales
William Prillaman wprillaman@havtech.com Inside Sales
Zachary Yamin zyamin@havtech.com Inside Sales
Havtech { DC - 2830 }
Email: marketing@havtech.com
Phone Number: (301) 206-9225
Mailing Address: 9505 Berger Road, Columbia, Maryland 21046 United States
Shipping Address: 9505 Berger Road, Columbia, Maryland 21046 United States
Name Email Title
Adam Becker abecker@havtech.com Inside Sales
Adam Jones adamjones@havtech.com Other(Warranty Specialist)
Al Hooreh ahooreh@havtech.com Inside Sales
Alex Catterton acatterton@havtech.com Inside Sales
Andrew Hartman andrewhartman@havtech.com Outside Sales
Andrew Neal andrewneal@havtech.com Estimator
Andriss Jourdan ajourdan@havtech.com Inside Sales
Andy Beal andybeal@havtech.com Outside Sales
Anthony Jones anthonyjones@havtech.com Other(Sales Engineer)
Armon Kazemi akazemi@havtech.com Other
Ashley Michno amichno@havtech.com Inside Sales
Austen Krause akrause@havtech.com Outside Sales
Ben Wesley bwesley@havtech.com Other(Field Service Engineer)
Benjamin Mensah benjamin@networkdepot.com Contracting Services
Bill Eberling beberling@havtech.com Other(Service Supervisor)
Brandon Conheim bconheim@havtech.com Outside Sales
Brandon Giron bgiron@havtech.com Other(Service Technician)
Brandon Schmoll bschmoll@havtech.com Other(Field Supervisor)
Brian Burns brb048@gmail.com Other
Brian Cook bcook@havtech.com Inside Sales
Brian Mitchell bmitchell@havtech.com Inside Sales
Brian Song briansong@havtech.com Controls
Brittany Seek bseek@havtech.com Inside Sales
Bryanne Marks bmarks@havtech.com Other(Financial)
Buddy Hardesty bhardesty@havtech.com Other(Field Service Engineer)
Carlos Chavez cchavez@havtech.com Other(Field Service Engineer)
Carlos Hoyos choyos@havtech.com Other(Field Service Engineer)
Casey McKay cmckay@havtech.com Outside Sales
Charles Auster causter@havtech.com Other(Field Service Engineer)
Charlie MacDonald charliemacdonald@havtech.com Inside Sales
Chris Eckenrode chriseckenrode@havtech.com Other(Financial)
Chris From Havtec rouzer81@gmail.com Other(Field Service Technician)
Chris Furbee cfurbee@havtech.com Other(Service Technician)
Chris Kiger ckiger@havtech.com Other(Field Service Engineer)
Chris Wilson cwilson@havtech.com Controls
Christian Drumm cdrumm@havtech.com Inside Sales
Christopher Zimmerman czimmerman@havtech.com Inside Sales
Chuck Hicks chicks@havtech.com Inside Sales
Connor Blood cblood@havtech.com Outside Sales
Cory Colassard ccolassard@havtech.com Outside Sales
Craig Eddy ceddy@havtech.com Other(Field Supervisor)
Dan Coombs dancoombs@havtech.com Other(Field Service Engineer)
Dan Davis dandavis@havtech.com Other(Service Sales Leader)
Dan May danmay@havtech.com Outside Sales
Danny Polliard dpolliard@havtech.com Other(Service Coordinator)
Darren IT Other(IT)
Daryl Moll dmoll@velosio.com Other(Principal Cloud Architect)
David Buckley davidbuckley@havtech.com Other(Field Service Engineer)
David Cunningham davidcunningham@havtech.com Outside Sales
David Llanos dllanos@havtech.com Other(Field Service Engineer)
Debra Brewer dbrewer@havtech.com Admin
Dennis Volostnykh dvolostnykh@havtech.com Inside Sales
Don Hinkle donhinkle@havtech.com Sales Support
Donnell Avery davery@havtech.com Inside Sales
Earl Wright earlwright@havtech.com Other
Ed Reed edreed@havtech.com Outside Sales
Edward Breitner ebreitner@havtech.com Other
Emily Panizari epanizari@havtech.com Inside Sales
Eric Gatton egatton@havtech.com Inside Sales
Eric Simpson esimpson@havtech.com Outside Sales
Eric Turner ericturner@havtech.com Other(Account Manager)
Erin Cousler ecousler@havtech.com Other(Marketing Director)
Eyal Haim eyalha80@gmail.com Other(Service Technician)
Francine Brant francinebrant@havtech.com Inside Sales
Greg Brooks gbrooks@havtech.com Other(Field Service Engineer)
Guy Hardesty guyhardesty@havtech.com Other(Service)
Halley Nye hanye@havtech.com Other(Service Technician)
Henry Adams hadams@havtech.com Inside Sales
Izat Majlaton imajlaton@havtech.com Inside Sales
Jackie Kiehl jkiehl@havtech.com Inside Sales
Jamie Riser jriser@havtech.com Other(Service Engineer)
Jarrett Mahaffey support@stratoscloud.net Contracting Services
Jason Charne jcharne@havtech.com Inside Sales
Jeff Cox jcox@havtech.com Sales Support
Jeffrey Cox jeffcox@havtech.com Principal
Jennifer Jenkins jenniferjenkins@havtech.com Principal
Jessica Inglis jessicainglis@havtech.com Inside Sales
Jessica Jones jessicajones@havtech.com Other(Applications Engineer)
Jesus Moreno jmoreno@havtech.com Other
Jim Kusick jkusick@havtech.com Outside Sales
Jim Randolph jimrandolph@havtech.com Other(Sales Engineer)
Jimmy Cahill jcahill@havtech.com Outside Sales
Jodi Bogue jodibogue@havtech.com Project Developer/Manager
Joe Boerlage jboerlage@havtech.com Other
Joe Wright jwright@havtech.com Inside Sales
John Goode-bey jonathongoode-bey@havtech.com Other
John Mullins jmullins@havtech.com Other(Field Service Engineer)
John Sparrow jsparrow@havtech.com Other(Field Service Engineer)
Jonathan Shim jonathanshim@havtech.com Other(Financial)
Jonathan Taylor jtaylor@havtech.com Other(Field Service Engineer)
Jonathon Good-Bey Other
Josh Dwyer jdwyer@havtech.com Sales Support
Josh Feshari jfeshari@havtech.com Inside Sales
Justin Ritthaler jritthaler@havtech.com Inside Sales
Keaton Pavier keatonpavier@havtech.com Inside Sales
Keith Gensch keithgensch@havtech.com Outside Sales
Keith Mohney kmohney@havtech.com Other
Keith Moore notavailable@notavailable.com Other(Technician)
Kevin Jewell kevinjewell@havtech.com Other(Service Tech)
Kevin Stroop kstroop@havtech.com Outside Sales
Kristen Novakovich kristennovakovich@havtech.com Other
Lacey Hollon lhollon@havtech.com Project Developer/Manager
Larry Manross larrymanross@havtech.com Other(Sales Engineer)
Laura Johnson ljohnson@havtech.com Admin
Lauren Peck lpeck@havtech.com Inside Sales
Leslie Baker lbaker@havtech.com Project Developer/Manager
Logan Stanley lstanley@havtech.com Inside Sales
Louis DiGiovanni ldigiovanni@havtech.com Other(Field Service Engineer)
Luke Jackson ljackson@havtech.com Outside Sales
Madison Balderston mbalderston@havtech.com Other(Project Administrator)
Madison Basham mbasham@havtech.com Inside Sales
Maggie Whitesel mwhitesel@havtech.com Inside Sales
Malek Nofal maleknofal@icloud.com Other(Field Service engineer)
Marcy Loy mloy@havtech.com Other(Service)
Mark Bailey mbailey@havtech.com Inside Sales
Mark Diodato mdiodato@havtech.com Outside Sales
Mark Matheson mmatheson@havtech.com Inside Sales
Mark Neely markneely@havtech.com Outside Sales
Mark Nelligan marknelligan@havtech.com Outside Sales
Mason Clairmont mclairmont@havtech.com Outside Sales
Matt Kling mattkling@havtech.com Outside Sales
Matt Troyer mtroyer@havtech.com Controls
Matt Winder mwinder@havtech.com Other
Matt Windor Other
Matthew Ruby matthewruby@havtech.com Other(Application Engineer)
Melissa Cary mcary@havtech.com Other(Service Coordinator)
Melissa Dennis mdennis@havtech.com Other(Marketing)
Michael Johnson mjohnson@havtech.com Other(Warehouse/Counter Sales Coordinator)
Mike Avon mavon@havtech.com Other(Apprentice)
Neil Rozich neilrozich@havtech.com Inside Sales
Nicholas Mirto nmirto@havtech.com Inside Sales
Nick Aumiller naumiller@havtech.com Controls
Nicole Holtz nholtz@havtech.com Inside Sales
Norm Long normlong@havtech.com Principal
Patrick Murdock patrickm@aceshvac.com Other(Equipment Sales Manager)
Paul Hoover paulhoover@havtech.com Other(Sr. Application Engineer)
Rami Hijaz rhijaz@havtech.com Inside Sales
Randohn Cornell rcornell@havtech.com Other
Randy Camp rcamp@havtech.com Other
Renee Childress rchildress@havtech.com Other(Commercial Distribution)
Rich Kewer richkewer@havtech.com Inside Sales
Richard Kewer rkewer@havtech.com Other(Application Engineer)
Rob Plummer rplummer@havtech.com Other
Robert Bliss rbliss@havtech.com Inside Sales
Ron Cook rcook@havtech.com Other(Field Service Engineer)
Rosalie Wampler rwampler@havtech.com Project Developer/Manager
Russell Kennedy rkennedy@havtech.com Inside Sales
Ryan Williams rwilliams@havtech.com Other
Sam Wilson swilson@havtech.com Other(Account Executive)
Semyon Friedman Other
Sezar Lizama slizama@havtech.com Other(Technician)
Shannon Beaty sbeaty@havtech.com Other(Field Service Engineer)
Shantwan Barnes sbarnes@havtech.com Other(Field Service Engineer)
Shawn McMillan smcmillan@havtech.com Other(Field Service Engineer)
Skip Wilson swilson@havtech.com Other(Account Manger)
Stanley Davis dandavis@havtech.com Other(Service)
Stephanie Holden stephanieholden@havtech.com Inside Sales
Stephanie Wilson stephaniewilson@havtech.com Inside Sales
Stephen Allen sallen@havtech.com Inside Sales
Steve Overton soverton@havtech.com Other(Service Supervisor)
Steve Prenger sprenger@havtech.com Other(Field Service Engineer)
Steven Park spark@havtech.com Inside Sales
Ted McCord tedmccord@havtech.com Outside Sales
Ted McCord tmccord@havtech.com Other(Sales Engineer)
Thor Fraser thorfraser@havtech.com Other(Sales Engineer)
Tim Carter tcarter@havtech.com Inside Sales
Tim Dorman timdorman@havtech.com Outside Sales
Tom Polansky tpolansky@spectrumenergyllc.com Sales Support
Tom Twigg ttwigg@havtech.com Other(Field Service Engineer)
Tommy Tugwell ttugwell@havtech.com Other(service technician)
Tony Giampietro tgiampietro@havtech.com Inside Sales
Trey Goulden treygoulden@havtech.com Outside Sales(Aftermarket Outside Sales)
Tuan Nguyen tnguyen@havtech.com Other(Field Service Engineer)
Virginia DAquila virginiadaquila@havtech.com Project Developer/Manager
Wade Theis wadetheis@havetech.com Other
Wade Thies wadethies@havtech.com Outside Sales
Walter Meyers Other
Weston Gearhart wgearhart@havtech.com Outside Sales
William Holtzman wholtzman@havtech.com Inside Sales
William Prillaman wprillaman@havtech.com Inside Sales
Yasmine Baldwin ybaldwin@havtech.com Other(Warranty Specialist)
Heaven Engineering Co. { Wichita - 2660 }
Email: markodonnell@heavenengineering.com
Phone Number: (316) 262-1244
Mailing Address: 340 S Pattie, Wichita, Kansas 67211 United States
Shipping Address: 340 S Pattie, Wichita, Kansas 67211 United States
Name Email Title
Dan Scott dan.scott@tmi-wichita.com Other(Service Technician)
Dario Zuniga dario@heavenengineering.com Inside Sales
Edward Dye merledye@heavenengineering.com Sales Support
Erik Maldonado erikmaldonado@heavenengineering.com Inside Sales
Greg Hummingbird greghummingbird@heavenengineering.com Outside Sales
Jeff Wiggins jeffwiggins@heavenengineering.com Inside Sales
Rick Shoemaker rickshoemaker@heavenengineering.com Sales Support
Hoffman & Hoffman, Inc. { Asheville - 3390 }
Email: brian.dietrich@hoffman-hoffman.com
Phone Number: (828) 296-0111
Mailing Address: 1388 Sandhill Rd, Suite 8, Candler, North Carolina 28715 United States
Shipping Address: 1388 Sandhill Rd, Suite 8, Candler, North Carolina 28715 United States
Name Email Title
Adam Kaufman adam.kaufman@hoffman-hoffman.com Outside Sales
Brian Dietrich brian.dietrich@hoffman-hoffman.com Branch Manager
Chris Huston chris.huston@hoffman-hoffman.com Branch Manager
Mindy Harrington mindy.harrington@hoffman-hoffman.com Outside Sales
Hoffman & Hoffman, Inc. { Charleston - 3380 }
Email: jimmy.king@hoffman-hoffman.com
Phone Number: (843) 884-3201
Mailing Address: 459 Deanna Lane, Wando, South Carolina 29492 United States
Shipping Address: 459 Deanna Lane, Wando, South Carolina 29492 United States
Name Email Title
Brady Shirley brady.shirley@hoffmech.com Contracting Services
Brent Jones brent.jones@hoffman-hoffman.com Outside Sales
Colt Grunsky colt.grunsky@hoffman-hoffman.com Inside Sales
Cooper Collins cooper.collins@hoffman-hoffman.com Outside Sales
Jimmy King jimmy.king@hoffman-hoffman.com Branch Manager
Mark Atwood mark.atwood@hoffmech.com Other(Operatins Manager)
Michael Cladakis mike.cladakis@hoffman-hoffman.com Outside Sales
Mike Cladakis mike.cladakis@hoffman-hoffman.com Other(Sales Engineer)
Robert Braswell robert.braswell@hoffman-hoffman.com Other
Ted Crawford ted.crawford@hoffman-hoffman.com Inside Sales
Trey Adams trey.adams@hoffman-hoffman.com Outside Sales
Waylon Ethridge waylon.ethridge@hoffman-hoffman.com Branch Manager
Hoffman & Hoffman, Inc. { Charlotte - 3220 }
Email: mike.bledsoe@hoffman-hoffman.com
Phone Number: (704) 364-4700
Mailing Address: 1133 Upper Asbury Avenue, Charlotte, North Carolina 28206 United States
Shipping Address: 1133 Upper Asbury Avenue, Charlotte, North Carolina 28206 United States
Name Email Title
Anna Devereaux anna.devereaux@hoffman-hoffman.com Outside Sales
Ben Bingham ben.bingham@hoffman-hoffman.com Other(Sales Engineer)
Ben Gearren ben.gearren@hoffman-hoffman.com Other
Benn Leggett benn.leggett@hoffmech.com Other(Sales Coordinator)
Blake Anderson blake.anderson@hoffman-hoffman.com Outside Sales
Bob Hicks bob.hicks@hoffmech.com Principal
Bret Wiseman bret.wiseman@hoffman-hoffman.com Inside Sales
Brian Milbourne brian.milbourne@hoffman-hoffman.com Branch Manager
Chase Crowder chase.crowder@hoffman-hoffman.com Outside Sales
Chris Arbogast chris.arbogast@hoffman-hoffman.com Outside Sales
Chuck Honeycutt chuck.honeycutt@hoffman-hoffman.com GM/VP
Claire Weiland claire.weiland@hoffman-hoffman.com Inside Sales
Clay Patterson clay.patterson@hoffman-hoffman.com Inside Sales
Colin Dee colin.dee@hoffman-hoffman.com Outside Sales
Craig Taylor craig.taylor@hoffmech.com Other(Area Manager)
Daniel Flora daniel.flora@hoffman-hoffman.com Outside Sales
Dave Johnson Other
David Price david.price@hoffman-hoffman.com Inside Sales
Eric Creel eric.creel@hoffman-hoffman.com Inside Sales
Jackson Bobo jackson.bobo@hoffman-hoffman.com Inside Sales
Jared Arriola jared.arriola@hoffman-hoffman.com Inside Sales
Jim Mangini jim.mangini@hoffman-hoffman.com Principal
Joe Schrader joe.schrader@hoffman-hoffman.com Outside Sales
John Lohr john.lohr@hoffman-hoffman.com Outside Sales
Kacey Hall kacey.hall@hoffmech.com Other(Service Administrator)
Ken Morris ken.morris@hoffman-hoffman.com Outside Sales
Kyle Barefoot kyle.barefoot@hoffman-hoffman.com Inside Sales
Lee Girardeau lee.girardeau@hoffman-hoffman.com Inside Sales
Lock Flowe lock.flowe@hoffman-hoffman.com Inside Sales
Marty Howle marty.howle@hoffmech.com Other(Director of Technical Operations)
Morgan McAteer morgan.mcateer@hoffman-hoffman.com Inside Sales
Nathan Sollenberger nathan.sollenberger@hoffman-hoffman.com Inside Sales
Philip Arnold philip.arnold@hoffman-hoffman.com Outside Sales
Preston Tompkins preston.tompkins@hoffmech.com Other(Team Leader)
Randy Aldridge Other
Ryan Kerfien ryan.kerfien@hoffman-hoffman.com Outside Sales
Ryan Staton ryan.staton@hoffman-hoffman.com Outside Sales
Sheelagh Dunn sheelagh.dunn@hoffman-hoffman.com Inside Sales
Spencer Jones spencer.jones@hoffman-hoffman.com Outside Sales
Stephen Mejia stephen.mejia@hoffmech.com Other(HVAC Service Tech Team Leader)
Stephen Oneil stephen.oneil@hoffman-hoffman.com Outside Sales
Steve Weaver steven.weaver@hussmann.com Other
Tim Buford tim.buford@hoffman-hoffman.com Principal
Tracy Smith tracy.smith@hoffman-hoffman.com Outside Sales
Trisha Wiedbrauk trisha.wiedbrauk@hoffman-hoffman.com Inside Sales
Victor Rangel victor.rangel@hoffman-hoffman.com Other
Hoffman & Hoffman, Inc. { Chattanooga - 3270 }
Email: kevin.milz@hoffman-hoffman.com
Phone Number: (423) 693-2890
Mailing Address: 6011 Century Oaks Dr., Chattanooga, Tennessee 37416 United States
Shipping Address: 6011 Century Oaks Dr., Chattanooga, Tennessee 37416 United States
Name Email Title
Alex Ramsey alex.ramsey@hoffman-hoffman.com Outside Sales
Carter Bell carter.bell@hoffman-hoffman.com Inside Sales
Cindy Ellison cindy.ellison@hoffman-hoffman.com Outside Sales
Jonathan Quinones jonathan.quinones@hoffman-hoffman.com Inside Sales
Kevin Milz kevin.milz@hoffman-hoffman.com Branch Manager
Nick Alley nick.alley@hoffman-hoffman.com Outside Sales
Hoffman & Hoffman, Inc. { Chesapeake - 3250 }
Email: greg.prose@hoffman-hoffman.com
Phone Number: (757) 548-1700
Mailing Address: 617 Innovation Drive, Suite 103, Chesapeake, Virginia 23320 United States
Shipping Address: 617 Innovation Drive, Suite 103, Chesapeake, Virginia 23320 United States
Name Email Title
Mark McIvor mark.mcivor@hoffman-hoffman.com Outside Sales
Hoffman & Hoffman, Inc. { Columbia - 3230 }
Email: darryl.frick@hoffman-hoffman.com
Phone Number: (803) 765-9360
Mailing Address: 104 Vantage Point Drive, Cayce, South Carolina 29033 United States
Shipping Address: 104 Vantage Point Drive, Cayce, South Carolina 29033 United States
Name Email Title
Austin Antley austin.antley@hoffman-hoffman.com Outside Sales
Brian Barnes brian.barnes@hoffman-hoffman.com Other
Brian Keefer brian.keefer@hoffman-hoffman.com Branch Manager
Brian Milbourne brian.milbourne@hoffman-hoffman.com Branch Manager
Buddy Robins Other
Cam Hricko cam.hricko@hoffman-hoffman.com Inside Sales
Cayman Hawke cayman.hawke@hoffmech.com Other
Clint Harmon clint.harmon@hoffman-hoffman.com Inside Sales
Corey Watts cory.watts@aol.com Controls
Courtney Saunders courtney.saunders@hoffman-hoffman.com Other(Warranty Administrator)
Dan Epperson dan.epperson@hoffman-hoffman.com Other(Service)
Darryl Frick darryl.frick@hoffman-hoffman.com Branch Manager
Denise Cross denise.cross@hoffman-hoffman.com Inside Sales
Geoff Hankins geoff.hankins@hoffman-hoffman.com Branch Manager
Grayson Mobley grayson.mobley@hoffman-hoffman.com Inside Sales
Hunter Wilson hunter.wilson@hoffman-hoffman.com Outside Sales
Jason Cliatt jason.cliatt@hoffman-hoffman.com Other
John Steele john.steele@hoffmech.com Principal
Jonathan Lambert jonathan.lambert@hoffman-hoffman.com Outside Sales
Josh Roberson josh.roberson@hoffman-hoffman.com Outside Sales
Justin Eversfield justin.eversfield@hoffman-hoffman.com Inside Sales
Justin Snipes justin.snipes@hoffman-hoffman.com Outside Sales
Kevin Coupal kevin.coupal@hoffman-hoffman.com Inside Sales
Lisa Henderson lisa.henderson@hoffman-hoffman.com Inside Sales
Mark Bell Other
Michael Rushing michael.rushing@hbtech.biz Outside Sales
Ray Boland ray.boland@hoffmech.com Project Developer/Manager
Rich Barton rich.barton@hoffman-hoffman.com Outside Sales
Robert Goss Other
Rusty Hoffman rusty.hoffman@hoffman-hoffman.com Principal
Ryan Douglass rwd207@gmail.com Other(Technical analyst)
Ryan Kerfien ryan.kerfien@hoffman-hoffman.com Outside Sales
Todd Woodrow todd.woodrow@hoffman-hoffman.com Outside Sales
Travis Dixon travis.dixon@hoffmech.com Other(HVAC Service Tech Team Leader)
Troy Pender troy.pender@hoffman-hoffman.com Other
Valeri Starcher valerie.starcher@hoffmech.com Other(Service Agreement Account Manager)
Vivian Wood vivian.wood@hoffman-hoffman.com Outside Sales
Zach Pratt zach.pratt@hoffman-hoffman.com Inside Sales
Hoffman & Hoffman, Inc. { Greensboro - 3210 }
Email: info@hoffman-hoffman.com
Phone Number: (336) 292-8777
Mailing Address: 3816 Patterson Street, Greensboro, North Carolina 27404 United States
Shipping Address: 3816 Patterson Street, Greensboro, North Carolina 27404 United States
Name Email Title
Adam Kaufman adam.kaufman@hoffman-hoffman.com Outside Sales
Amber Kulick amber.kulick@hoffman-hoffman.com Sales Support
Barry Biggs barry.biggs@hoffman-hoffman.com Other(Whs Sales & Inventory)
Bennett Funderburk bennett.funderburk@hoffman-hoffman.com Branch Manager
Bill Harris bill.harris@hoffmech.com Other
Camron Smith camron.smith@hoffman-hoffman.com Inside Sales
Chad James chad.james@hoffman-hoffman.com Other(Service technician)
Chad Mendenhall chad.mendenhall@hoffmech.com Other(Dir of Tech Operations)
Charlie Crosby charlie.crosby@hoffman-hoffman.com Inside Sales
Chase Crowder chase.crowder@hoffman-hoffman.com Outside Sales
Chris Bennett chris.bennett@hoffmech.com Other(Area Manager)
Chris Frandock chris.frandock@hbtech.biz Other(Service)
Chris Hanks chris.hanks@hoffman-hoffman.com Sales Support
Chris Stegall chris.stegall@hbtech.biz Other(Operations Manager)
Chris Turner chris.turner@hoffmech.com Other
Christine Flowe christine.flowe@hbtech.biz Controls
Cindy Jordan cindy.jordan@hoffman-hoffman.com Admin
Danny Moore danny.moore@hoffmech.com Other
Danny Woyahn danny.woyahn@hoffman-hoffman.com Outside Sales
Darren Stafford darren.stafford@hbtech.biz Other(HBT Engineering (Sales))
Daryl Showalter daryl.showalter@hoffman-hoffman.com Principal
David Autrey dave.autrey@hoffman-hoffman.com Outside Sales
David Owen david.owen@hbtech.biz Other(DDC Customer Service)
David Riley david.riley@hoffmech.com Contracting Services
Debbie Herndon debbie.herndon@hoffman-hoffman.com Other(Executive Assistant)
Debi Snider debi.snider@hoffman-hoffman.com Sales Support
Dominick Goldston dominick.goldston@hoffman-hoffman.com Inside Sales
Edwin Rivera edwin.rivera@hoffman-hoffman.com Other(IT Support Specialist)
Gary Marshall gary.marshall@hoffman-hoffman.com Principal
Heather Fowler heather.fowler@hoffman-hoffman.com Other
India Alexander india.alexander@hoffman-hoffman.com Admin
Jason Gaertner jason.gaertner@hoffman-hoffman.com Other(Parts)
Jeff Hunt jeff.hunt2@hoffman-hoffman.com Inside Sales
Jim Bingham jim.bingham@hoffman-hoffman.com Other
John Chandler john.chandler@hoffman-hoffman.com Principal
John Green john.green@hoffman-hoffman.com Outside Sales
Jordan Robinson jordan.robinson@hoffman-hoffman.com Other
Kelly Patterson kelly.patterson@hoffman-hoffman.com Other(Director of Marketing)
Kevin Davis kevin.davis@hoffmech.com Other(Director of VRV Operations)
Kevin McDonald kevin.mcdonald@hoffman-hoffman.com Outside Sales
Lisa Walston lisa.walston@hoffman-hoffman.com Other(Sr. Executive Assistant)
Marsha Tuft marsha.tuft@hoffman-hoffman.com Outside Sales
Melissa Grubb melissa.grubb@hoffman-hoffman.com Other(Warranty Adrmistrator)
Michael Whitten michael.whitten@hoffman-hoffman.com Sales Support
Mikaila Miros mikaila.miros@hoffman-hoffman.com Other(Aftermarket Parts Technician)
Nate Helms nate.helms@hoffman-hoffman.com Outside Sales
Nathan Sollenberger nathan.sollenberger@hoffman-hoffman.com Inside Sales
Parts Team parts@hoffman-hoffman.com Other(Aftermarket Parts Team)
Rachel Luchs rachel.luchs@hoffman-hoffman.com Other(Marketing)
Randy Collins randy.collins@hoffman-hoffman.com Other(Owner Advocate)
Rebecca Hall rebecca.hall@hoffman-hoffman.com Other
Rhett Williams Other
Rick Schnarr rick.schnarr@hoffman-hoffman.com Principal
Robert Amos robert.amos@hoffman-hoffman.com Inside Sales
Rusty Hoffman rusty.hoffman@hoffman-hoffman.com Principal
Ryan Ballard ryann.ballard@hoffmech.com Other
Ryan Milleson ryan.milleson@hoffman-hoffman.com Other(AfterMarket Parts Technician)
Scott Hudson scott.hudson@hoffman-hoffman.com Outside Sales
Seth Byrd seth.byrd@hoffman-hoffman.com Other(IT Support)
Shannon Walters shannon.walters@hoffmech.com Other(Dir of Tech Operations)
Shelly Hawkes shelly.hawkes@hoffman-hoffman.com Sales Support
Steve Carter steve.carter@hbtech.biz Controls
Tanner Easterday tanner.easterday@hoffman-hoffman.com Inside Sales
Wayne Stapleton wayne.stapleton@hoffmech.com Other
Will Shore will.shore@hoffman-hoffman.com Outside Sales
Zachary Craver zachary.craver@hoffman-hoffman.com Inside Sales
Hoffman & Hoffman, Inc. { Greenville - 3240 }
Email: jay.hannah@hoffman-hoffman.com
Phone Number: (864) 676-1888
Mailing Address: 95 Marcus Drive, Creekside Park Greenville, South Carolina 29615 United States
Shipping Address: 95 Marcus Drive, Creekside Park Greenville, South Carolina 29615 United States
Name Email Title
Art Hudson art.hudson@hoffman-hoffman.com Outside Sales
Bill Bowers bill.bowers@hoffman-hoffman.com Outside Sales
Brad Davis brad.davis@hoffman-hoffman.com Outside Sales
Brent Abbott brent.abbott@hoffman-hoffman.com Outside Sales
James Einwaechter james.einwaechter@hoffman-hoffman.com Inside Sales
Jay Hannah jay.hannah@hoffman-hoffman.com Branch Manager
Lynne Davis lynne.davis@hoffman-hoffman.com Sales Support
Meredith Sloan meredith.sloan@hoffman-hoffman.com Sales Support
Mike Blakley mike.blakley@hoffman-hoffman.com Outside Sales
Pat Lawson pat.lawson@hoffman-hoffman.com Outside Sales
Hoffman & Hoffman, Inc. { Knoxville - 3260 }
Email: duke.bennett@hoffman-hoffman.com
Phone Number: (865) 450-9770
Mailing Address: 408 Erin Drive, Knoxville, Tennessee 37919 United States
Shipping Address: 408 Erin Drive, Knoxville, Tennessee 37919 United States
Name Email Title
Amanda Garrison amanda.garrison@hoffman-hoffman.com Inside Sales
Andrew Maki andrew.maki@hoffmech.com Other
Barry Dunford barry.dunford@hoffman-hoffman.com Inside Sales
Brett Harris brett.harris@hoffman-hoffman.com Principal
Curtis Bixler curtis.bixler@hoffman-hoffman.com Outside Sales
Darren Price darren.price@hoffman-hoffman.com Outside Sales
Dillon Dixon dillon.dixon@hoffman-hoffman.com Inside Sales
Jason Reagan jason.reagan@hoffman-hoffman.com Outside Sales
Jason Reagan jason.reagan@hoffmech.com Other(Dir of Tech Operations)
Jeff Greeley jeff.greeley@hoffman-hoffman.com Outside Sales
Jonathan McCulla johnathan.mcculla@hoffman-hoffman.com Outside Sales
Josh Rubins josh.rubins@hoffman-hoffman.com Outside Sales
Julia Fox julia.fox@hoffman-hoffman.com Other(Service Coordinator)
Justin Ford justin.ford@hoffman-hoffman.com Outside Sales
Justin King justin.king@hoffmech.com Other
Justin Novotny justin.novotny@hoffmech.com Other
Keith Havens keith.havens@hoffman-hoffman.com Inside Sales
Kevin Milz kevin.milz@hoffman-hoffman.com Branch Manager
Kevin Stopper kevin.stopper@hoffman-hoffman.com Inside Sales
Kyle Adkins kyle.adkins@hbtech.com Other
Logan Flowers logan.flowers@hoffman-hoffman.com Inside Sales
Shannon Newton shannon.newton@hoffmech.com Other
Tommy Johnston tommy.johnston@hoffmech.com Other(Service Tech)
Hoffman & Hoffman, Inc. { Raleigh - 3360 }
Email: bennett.funderburk@hoffman-hoffman.com
Phone Number: (919) 781-8011
Mailing Address: 2741 Noblin Road,Suite 100, Raleigh, North Carolina 27604 United States
Shipping Address: 2741 Noblin Road,Suite 100, Raleigh, North Carolina 27604 United States
Name Email Title
Adam Hoffman adam.hoffman@hoffman-hoffman.com Outside Sales
Aiden Kautz aiden.kautz@hoffman-hoffman.com Outside Sales
Ben Bingham ben.bingham@hoffman-hoffman.com Outside Sales
Bennett Funderburk bennett.funderburk@hoffman-hoffman.com Branch Manager
Brad Tilley brad.tilley@hoffmech.com Other
Cameron Byrd cameron.byrd@hoffman-hoffman.com Inside Sales
Chris Parks chris.parks@hoffman-hoffman.com Outside Sales
Cory Adcroft cory.adcroft@hoffman-hoffman.com Outside Sales
Daniel Lockerby daniel.lockerby@hoffman-hoffman.com Other(AC Drives Specilist)
David Lankshear david.lankshear@hoffmech.com Other(Service Technician)
Eric Einwaechter eric.einwaechter@hoffman-hoffman.com Outside Sales
James Brown james.brown@hbtech.biz Other
Jamie Franks Other
Kirk Mckee kirk.mckee@hoffmech.com Other(Service Technician)
Michael McQueen michael.mcqueen@hoffman-hoffman.com Outside Sales
Robert Chapman craig.chapman@hoffman-hoffman.com Outside Sales
Ron Jones ron.jones@hoffman-hoffman.com Outside Sales
Sean O'Keeffe sean.okeeffe@hoffman-hoffman.com Other(Project Sales Engineer)
Steve Jones stephen.jones@hoffmech.com Other(Area Manager)
TJ Bell tj.bell@hoffman-hoffman.com Outside Sales
Tripp Loflin tripp.loflin@hoffman-hoffman.com Outside Sales
Vijay Periannan vijay.periannan@hoffman-hoffman.com Outside Sales
Warren Lancaster warren.lancaster@hoffmech.com Other(HVAC Service Tech Team Leader)
Hoffman & Hoffman, Inc. { Wilmington - 3350 }
Email: Brian.Keefer@hoffman-hoffman.com
Phone Number: (910) 791-4775
Mailing Address: 6615-B Windmill Way, Wilmington, North Carolina 28405 United States
Shipping Address: 6615-B Windmill Way, Wilmington, North Carolina 28405 United States
Name Email Title
Alex Shaffer alex.shaffer@hoffman-hoffman.com Inside Sales
Amy McCartney amy.mccartney@hoffman-hoffman.com Inside Sales
Brandon Redding brandon.redding@hoffman-hoffman.com Other(Inside Sales Manager)
Brian Keefer brian.keefer@hoffman-hoffman.com Branch Manager
Chris Cimino chris.cimino@hoffman-hoffman.com Outside Sales
Greg Ballard greg.ballard@hoffmech.com Other
Rob Thompson rob.thompson@hoffman-hoffman.com Outside Sales
Sam Starling sam.starling@hoffman-hoffman.com Inside Sales
Vince Long vince.long@hoffman-hoffman.com Inside Sales
House Parts Direct { Minneapolis - 1004 }
Email:
Phone Number: (763) 553-5330
Mailing Address: 13600 Industrial Park Blvd, Minneapolis, Minnesota 55441 United States
Shipping Address: 13600 Industrial Park Blvd, Minneapolis, Minnesota 55441 United States
Name Email Title
Adam Caver adam.caver@daikinapplied.com Other(Parts Sales Specialist)
Adam Cornell adam.cornell@daikinapplied.com Other(Regional Parts Sales Manager)
Jamaal Wesley jamaal.wesley1@daikinapplied.com Other(Technician)
Matthew-Michael Hines matthew.hines@daikinapplied.com Inside Sales
Parts Employee Other
HTS Engineering Ltd. { Beaumont - 6000B }
Email: texas@hts.com
Phone Number: (409) 833-7120
Mailing Address: 3050 C Rusk Street, Beaumont, Texas 77702 United States
Shipping Address: 3050 C Rusk Street, Beaumont, Texas 77702 United States
Name Email Title
Arlindo Simoes arlindo.simoes@hts.com Contracting Services
John Zackary john.zackary@hts.com Branch Manager
HTS Engineering Ltd. { London - 6020 }
Email: info_london@hts.com
Phone Number: (519) 457-6700
Mailing Address: 320 Neptune Crescent Unit #6, London, Ontario N6M 1A1 Canada
Shipping Address: 320 Neptune Crescent Unit #6, London, Ontario N6M 1A1 Canada
Name Email Title
AJ Phelps Other
Amanda Vanhooydonk amanda.vanhooydonk@hts.com Other(Parts)
Brad Visscher brad.visscher@hts.com Other
Brody ODonnell brody.odonnell@hts.com Other(Inside Sales)
Chris Goldie chris.goldie@hts.com Other
Corey Jones corey.jones@hts.com Other
Howard Robertson howard.robertson@hts.com Other
Jim Bender jim.bender@hts.com Outside Sales
Jonathan Sinden jonathan.sinden@hts.com Other(Account Executive, Southwestern Ontario)
Mark Vetero mark.vetero@hts.com Outside Sales
Randy Ronson randy.ronson@hts.com Other
Terry Arcese terry.arcese@hts.com Branch Manager
Trevor Rideout trevor.rideout@hts.com Outside Sales
HTS Engineering Ltd. { Oshawa - 6050 }
Email: info_oshawa@hts.com
Phone Number: (905) 579-6700
Mailing Address: 2001 Thickson Road South,Unit # 11, Whitby, Ontario L1N 6J3 Canada
Shipping Address: 2001 Thickson Road South,Unit # 11, Whitby, Ontario L1N 6J3 Canada
Name Email Title
Al Hahn al.hahn@hts.com Outside Sales
Alix Falconer alix.falconer@hts.com Inside Sales
Christian Sawyer christian.sawyer@hts.com Inside Sales
Christine Cormier christine.cormier@hts.com Outside Sales
Danny Russell danny.russell@hts.com Outside Sales
Gavin Bradley gavin.bradley@hts.com Branch Manager
Josh Aquino josh.aquino@hts.com Inside Sales
Kevin Wrubel kevin.wrubel@hts.com Inside Sales
Klaudio Uruci klaudio.uruci@hts.com Inside Sales
Lauren Lavalley lauren.lavalley@hts.com Inside Sales
Shawn Simmons shawn.simmons@hts.com Outside Sales
Wrai Sabatini wrai.sabatini@hts.com Outside Sales
HTS Engineering Ltd. { Ottawa - 5880 }
Email: info_ottawa@hts.com
Phone Number: (613) 728-7400
Mailing Address: 830 Campbell Avenue, Ottawa, Ontario K2A 2C2 Canada
Shipping Address: 830 Campbell Avenue, Ottawa, Ontario K2A 2C2 Canada
Name Email Title
Abdulla Saleh abdulla.saleh@hts.com Inside Sales
Adam Boyd adam.boyd@hts.com Inside Sales
Adam Graham adam.graham@hts.com Outside Sales
Aleksa Marinkov aleksa.marinkov@hts.com Outside Sales
Alie Saad alie.saad@hts.com Branch Manager
Andreas Janse andreas.janse@hts.com Inside Sales
Andrew Wilson andrew.wilson@hts.com Inside Sales
Andy Lancefield andy.lancefield@hts.com Outside Sales
Andy N/A Other
Angela Murray angela.murray@hts.com Outside Sales
Brad Barkauskas brad.barkauskas@hts.com Outside Sales
Brandon Garnett brandon.garnett@hts.com Inside Sales
Brandon Yee brandon.yee@hts.com Inside Sales
Brian Gerow brian.gerow@hts.com Outside Sales
Brock Hutchison brock.hutchison@hts.com Principal
Carmen Lefebvre carmen.lefebvre@hts.com Outside Sales
Caroline Faubert caroline.faubert@hts.com Inside Sales
Connor Harper connor.harper@hts.com Inside Sales
Dan Holmes dan.holmes@hts.com Controls
David Macphee david.macphee@hts.com Inside Sales
David Michelin david.michelin@hts.com Outside Sales
Derek Breckenridge derek.breckenridge@hts.com Other(Service Equip Supv)
Descartes Lumingu descartes.lumingu@hts.com Inside Sales
Dylan Brown dylan.brown@hts.com Outside Sales
Eric Colvin eric.colvin@hts.com Other(Project Manager)
Gary Hartmann gary.hartmann@hts.com Outside Sales
James Gubbels james.gubbels@hts.com Inside Sales
Jason Imbeau jason.imbeau@hts.com Inside Sales
Jason Kitchen jason.kitchen@hts.com Outside Sales(Director Director)
Jean Gautreau jp.gautreau@hts.com Other(Service)
Jean-David Duchesne jeandavid.duchesne@hts.com Outside Sales
Khalid Al Tawil khalid.al.tawil@hts.com Principal
Kyle Hampson kyle.hampson@hts.com Outside Sales
Leah Ryan leah.ryan@hts.com Inside Sales
Lee Mcculloch lee.mcculloch@hts.com Other(Service Technician)
Maxime Lepage maxime.lepage@hts.com Outside Sales
Maxine Speers maxine.speers@hts.com Inside Sales
Meryl Patterson meryl.patterson@hts.com Other(Service Technician)
Mike Pinault michael.pinault@hts.com Other(Service)
Nick Amlin nick.amlin@hts.com Outside Sales
Ouissal El Hasanoui ouissal.elhasanoui@hts.com Inside Sales
Randy Beaudry randy.beaudry@hts.com Principal(Parts & Aftermarket Account Executive)
Riley Moss riley.moss@hts.com Inside Sales
Rod Lancefield rod.lancefield@hts.com Principal
Sandra Umurerwa sandra.umurerwa@hts.com Inside Sales
Sean Rouhani sean.rouhani@hts.com Outside Sales
Stephane Charbonneau stephane.charbonneau@hts.com Inside Sales
Stephanie St. Amour stephanie.st.amour@hts.com Principal(Parts and Aftermarket Inside/Counter Sal)
Suhib Abushariha suhib.abushariha@hts.com Outside Sales
Thomas Farrell thomas.farrell@hts.com Principal
Thomas Weiner thomas.weiner@hts.com Inside Sales
Tyler Perley Robertson tyler.perleyrobertson@hts.com Inside Sales
Tyler Robertson tyler.perley-roberston@hts.com Other
Tyler Watson tyler.watson@hts.com Inside Sales
Wael Khalaf wael.khalaf@hts.com Outside Sales
Youssef Lahlou youssef.lahlou@hts.com Inside Sales
Zach Riley zach.riley@hts.com Inside Sales
Ziad Eid ziad.eid@hts.com Inside Sales
HTS Engineering Ltd. { Stoney Creek - 5990 }
Email: info_hamilton@hts.com
Phone Number: (905) 643-7719
Mailing Address: 735 South Service Road,Unit 4, Stoney Creek, Ontario L8E 5Z2 Canada
Shipping Address: 735 South Service Road,Unit 4, Stoney Creek, Ontario L8E 5Z2 Canada
Name Email Title
Anthony Powell anthony.powell@hts.com Inside Sales
Billy Chan billy.chan@hts.com Inside Sales
Bob Mosley bob.mosley@hts.com Outside Sales
Brian Heans brian.heans@hts.com Outside Sales
Julia Bauer julia.bauer@hts.com Inside Sales
Kevin Little kevin.little@hts.com Other(Partner)
Kevin Phillips kevin.phillips@hts.com Outside Sales
Kierra McDougall kierra.mcdougall@hts.com Inside Sales
Kyle O'Connor kyle.oconnor@hts.com Inside Sales
Lauren Lavalley lauren.lavalley@hts.com Inside Sales
Leslie DeBernardi leslie.debernardi@hts.com Outside Sales
Madeline Smith madeline.smith@hts.com Inside Sales
Michael Harris michael.harris@hts.com Principal
Michael Pei michael.pei@hts.com Inside Sales
Mikayla Spero mikayla.spero@hts.com Inside Sales
Olivia Cirone olivia.cirone@hts.com Inside Sales
Riley Kool riley.kool@hts.com Outside Sales
Tyler Fessenden tyler.fessenden@hts.com Inside Sales
HTS Engineering Ltd. { Sudbury - 6040 }
Email: info_sudbury@hts.com
Phone Number: (705) 855-1589
Mailing Address: 3555 Highway #144, Unit #4, Chelmsford, Ontario P0M 1L0 Canada
Shipping Address: 3555 Highway #144, Unit #4, Chelmsford, Ontario P0M 1L0 Canada
Name Email Title
Abdulai Jalloh abdulai.jalloh@hts.com Inside Sales
Andy Selin andy.selin@hts.com Outside Sales(Director-Contracting Sales)
Barry Jesso barry.jesso@hts.com Outside Sales
Cole Bartok cole.bartok@hts.com Inside Sales
Dylan Brown dylan.brown@hts.com Outside Sales
Eric Larabie eric.larabie@hts.com Other
Erin Cox erin.cox@hts.com Inside Sales
Hasan Shahzad hasan.shahzad@hts.com Inside Sales
Jamie Ashe jamie.ashe@hts.com Branch Manager
Jason Kitchen jason.kitchen@hts.com Outside Sales(Director Director)
Paul Pilutti paul.pilutti@hts.com Other(Principal)
Shreyash Nandapure shreyash.nandapure@hts.com Inside Sales
HTS Engineering Ltd. { Toronto - 5950 }
Email: info_toronto@hts.com
Phone Number: (416) 661-3400
Mailing Address: 115 Norfinch Drive, North York, Ontario M3N 1W8 Canada
Shipping Address: 115 Norfinch Drive, North York, Ontario M3N 1W8 Canada
Name Email Title
Aaren Iannaci aaren.iannaci@hts.com Sales Support(Employee)
Aaron Pereira aaron.pereira@hts.com Other
Abby Livisky abby.livisky@hts.com Inside Sales
Abishan Umashanker abishan.umashanker@hts.com Inside Sales
Adam Caprini adam.caprini@hts.com Outside Sales
Aidan Hilborn Other
Akshay Khuggar akshay.khuggar@hts.com Inside Sales
Al Hahan al.hahan@hts.com Other
Al Walcroft al.walcroft@hts.com Outside Sales(Director-Contracting Sales)
Alejandro Navarro alejandro.navarro@hts.com Principal
Alex Forsea alex.forsea@hts.com Outside Sales
Alex Gallacher alex.gallacher@hts.com Outside Sales
Alex Serrano alex.serrano@hts.com Controls
Alex Varga alex.varga@hts.com Outside Sales
Alford Higgins alford.higgins@hts.com Outside Sales
Alfredo Alfano alfredo.alfano@hts.com Other(Service Mechanic)
Ali Markhali ali.markhali@hts.com Outside Sales
Alyssa Chote alyssa.chote@hts.com Inside Sales
Alyssa Gomez alyssa.gomez@hts.com Other(Service Coordinator)
Amaury Williams amaury.williams@hts.com Other
Anastasia Lafrance anastasia.lafrance@hts.com Other(Customer Service and Warranty)
Andre Drapeau andre.drapeau@hts.com Principal
Andre Grapeau Other
Andrew Fazio andrew.fazio@hts.com Inside Sales
Andrew Ohi andrew.ohi@hts.com Inside Sales
Andy Selin andy.selin@hts.com Outside Sales(Director-Contracting Sales)
Anish Basak anish.basak@hts.com Inside Sales
Ankur Patel ankur.patel@hts.com Other
Anthony DeGirolamo anthony.degirolamo@hts.com Other(Inside Sales)
Arda Safkan arda.safkan@hts.com Inside Sales
Arindo Simoes Other
Aryan Majumder aryan.majumder@hts.com Inside Sales
Asif Ghayoor asif.ghayoor@hts.com Sales Support(Employee)
Ben Bernier ben.bernier@hts.com Principal
Benjamin See benjamin.see@hts.com Inside Sales
Bibi Bundhoo bibi.bundhoo@hts.com Inside Sales
Bob Mosley bob.mosley@hts.com Outside Sales
Boss Omeire boss.omeire@hts.com Inside Sales
Brad Hughes brad.hughes@hts.com Sales Support(Employee)
Brad Riches brad.riches@hts.com Other
Braden Bartoshewski braden.bartoshewski@hts.com Outside Sales
Braydon Grice-Sams braydon.gricesams@hts.com Other(Apprentice)
Brendan Melanson brendan.melanson@hts.com Inside Sales
Brian Boughner brian.boughner@hts.com Other(Account Executive)
Brian Heans brian.heans@hts.com Outside Sales
Brian McCullough brian.mccullough@hts.com Inside Sales
Brock Hutchinson brock.hutchison@hts.com Other
Brody ODonnell brody.odonnell@hts.com Other(Inside Sales)
Bryce Wedow bryce.wedow@hts.com Principal
Caleb Wong caleb.wong@hts.com Inside Sales
Cam Fryer cam.fryer@hts.com Sales Support(Employee)
Chad Burton chad.burton@hts.com Other
Chad Johnson chad.johnson@hts.com Inside Sales
Chad Smith chad.smith@hts.com Outside Sales
Chantalle Cheung chantalle.cheung@dxseng.com Other(Engineering Co-op)
Charlotte Paton charlotte.paton@hts.com Inside Sales
Cherry Xu cherry.xu@hts.com Outside Sales(Contracting Sales)
Christine Cormier christine.cormier@hts.com Outside Sales
Christopher Coffey chris.coffey@hts.com Inside Sales
Christopher Elliot christopher.elliott@hts.com Other
Craig Lee craig.lee@hts.com Outside Sales
Curtis Ballesteros curtis.ballesteros@hts.com Inside Sales
Curtis Metrow curtis.metrow@hts.com Inside Sales
Dale Deosaran daled@beringmechanical.com Admin
Daniel E'Ippolito daniel.dippolito@htseng.com Project Developer/Manager
Daniel Munnick daniel.munnick@hts.com Inside Sales
Danny Russell danny.russell@hts.com Outside Sales
Darek Blackwell darek.blackwell@hts.com Inside Sales
Darrell McKenna darrellm@htseng.com Outside Sales
Dave Kviring david.kviring@hts.com Controls
David Ackah david.ackah@hts.com Inside Sales
David Majda david.majda@hts.com Outside Sales
Derek Gordon derek.gordon@hts.com Principal
Derek Kelloway derek.kelloway@hotmail.com Other
Derek Podsiadly derek.podsiadly@hts.com Outside Sales
Deric Park deric.park@hts.com Inside Sales
Dustin Davis dustin.davis@hts.com Inside Sales
Dylan Walton dylan.walton@hts.com Outside Sales
Eric Knockwood eric.knockwood@hts.com Inside Sales
Etan Gill ethan.gill@hts.com Inside Sales
Ethan Hafner ethan.hafner@hts.com Inside Sales
Ethan Singh ethan.singh@hts.com Inside Sales
Ethan Stratton ethan.stratton@hts.com Inside Sales
Etienne Fleck etienne.fleck@hts.com Inside Sales
Faith Joseph faith.joseph@hts.com Inside Sales
Farnoosh Zadeh farnoosh.zadeh@hts.com Other(IT Support)
Fatma Abdalla fatma.abdalla@hts.com Inside Sales
Fedor Sobolev fedor.sobolev@hts.com Outside Sales
Frances Lopes frances.lopes@hts.com Outside Sales
Francisco Huerta francisco.huerta@hts.com Inside Sales
Frank Triolo frank.triolo@hts.com Other(Traffic)
Fulvia Sperandio fulvia.sperandio@hts.com Other(Service)
Gavin Bradley gavin.bradley@hts.com Branch Manager
Geoff Wallis geoff.wallis@hts.com Inside Sales
Glenn Janes glenn.janes@hts.com Outside Sales
Graham Coote graham.coote@hts.com Outside Sales
Graham Jones graham.jones@hts.com Principal
Guillermo Garcia guillermo.garcia@hts.com Other
Harris Bransch harris.bransch@hts.com Other
Holly Bruce holly.bruce@hts.com Inside Sales
Ian Droog ian.droog@hts.com Outside Sales
Ian Rajkumar ian.rajkumar@dxseng.com Inside Sales
Ivan Baric ivan.baric@hts.com Inside Sales
Jack Brinneman jack.brinneman@hts.com Other(Service Technician)
Jack Dawson jack.dawson@hts.com Inside Sales
Jaden Sebu jaden.sebu@hts.com Inside Sales
Jake Hodgson jake.hodgson@hts.com Controls
James Breckenridge james.breckenridge@hts.com Controls
James Kelly james.kelly@dxseng.com Principal
Jamie Ha jamie.ha@hts.com Inside Sales
Jason Bentley jbentley@linkedin.com Other
Jason Eitel jason.eitel@hts.com Inside Sales
Jason Fernandes jason.fernandes@hts.com Inside Sales
Jason Giannis jason.giannis@hts.com Inside Sales
Jason Henderson jason.henderson@hts.com Outside Sales
Jason Li jason.li@hts.com Inside Sales
Jason Watson jason.watson@hts.com Other(Service Technician)
Jason Young jason.young@hts.com Controls
Jay Irwin jay.irwin@hts.com Outside Sales
Jeremy He jeremy.he@hts.com Outside Sales
Jerry Jerry Other
Jibrail Bhagwandass jibrail.bhagwandass@hts.com Inside Sales
Jim Kay jim.kay@hts.com Other(Partner)
JinLong Ye jinlong.ye@hts.com Other(IT)
Joe DiCarlo joe.dicarlo@hts.com Project Developer/Manager
Joe Frame Other
Joelle Cochrane joelle.cochrane@hts.com Inside Sales
John Samson john.samson@hts.com Outside Sales
Johnathon Cai johnathon.cai@dxseng.com Outside Sales(Contracting Sales)
Jonathan Kukucska jonathan.kukucska@hts.com Sales Support(Employee)
Jonathan Lewis jonathan.lewis@hts.com Outside Sales
Jonathan Trinh jonathan.trinh@hts.com Outside Sales
Jonathon Trinh jonathan.trinh@hts.com Inside Sales
Jose Rangel jose.rangel@hts.com Other(Service Technician)
Jose Vela jose.vela@hts.com Principal
JS Rancourt js.rancourt@dxseng.com Principal
Julio Mendoza julio.mendoza@hts.com Other
Kaelyn Hill kaelyn.hill@hts.com Inside Sales
Kandee Panch kandee.panch@hts.com Other(Financial)
Kartik Singla kartik.singla@dxseng.com Principal
Kaushik Sarkar kaushik.sarkar@hts.com Inside Sales
Kelsey Black kelsey.black@hts.com Inside Sales
Kenny Septyanto kenny.septyanto@hts.com Inside Sales
Kevin Little kevin.little@hts.com Other(Partner)
Kevin Roh kevin.roh@hts.com Inside Sales
Kevin Vuong kevin.vuong@hts.com Inside Sales
Kiran Maharaj kiran.maharaj@hts.com Inside Sales
Kyle O'Connor kyle.oconnor@hts.com Inside Sales
Kyle Rubenstein kyle.rubenstein@hts.com Other(Service Supervisor)
Kylie Chapman kylie.chapman@hts.com Inside Sales
Larry Patterson Other
Leanid Hdalevich leanid.hdalevich@hts.com Inside Sales
Leigh-Anne McKnight leigh-anne.mcknight@dxseng.com Inside Sales
Lorenzo Belanger lorenzo.belanger@hts.com Inside Sales
Madana Persaud madana.persaud@hts.com Other(Financial)
Madina Gotova madina.gotova@hts.com Other(IT)
Malik Huzaifa malik.huzaifa@hts.com Inside Sales
Mansaran Baath mansaran.baath@hts.com Inside Sales
Marc Paquette marc.paquette@hts.com Outside Sales
Marco Meli marco.meli@hts.com Inside Sales
Marek Polak marek.polak@hts.com Inside Sales
Mark Driscoll mark.driscoll@hts.com Sales Support(Employee)
Mark Logiudice mark.logiudice@hts.com Other(Parts)
Mark McIsaac mark.mcisaac@hts.com Controls
Mark Walker mark.walker@hts.com Outside Sales
Matej Mincev matej.mincev@hts.com Inside Sales
Mathis Turgeon-Roy mathis.turgeonroy@hts.com Inside Sales
Mayank Kasliwal mayank.kasliwal@hts.com Outside Sales
Michael Cortese michael.cortese@hts.com Inside Sales
Michael Durante michael.durante@hts.com Inside Sales
Michael Harris michael.harris@hts.com Principal
Michael Kiszka michael.kiszka@hts.com Inside Sales
Michael Orrett michael.orrett@hts.com Inside Sales
Michael Tam michael.tam@hts.com Other(Parts)
Michael Wieczorek michael.wieczorek@hts.com Outside Sales
Mike Clark Other
Mike Harris michael.harris@hts.com Other(Sales Engineer)
Mike Lafferton mike.lafferton@hts.com Controls
Mike Saccucci mike.saccucci@hts.com Outside Sales
Miranda Bundgard miranda.bundgard@hts.com Other(Inside Sales)
Mitchell Saline no2@email.com Other
Moe Saqqa moe.saqqa@hts.com Sales Support(Employee)
Mohammad Shamail mohammad.shamail@hts.com Inside Sales
Mohammad Shariff mohammad.shariff@hts.com Inside Sales
Mohammad Totah mohammad.totah@hts.com Outside Sales
Mohannad Shilbayeh mohannad.shilbayeh@hts.com Inside Sales
Moinuddin Sekander moinuddin.sekander@hts.com Inside Sales
Nathalie Sa'adeh nathalie.saadeh@hts.com Other(Inside Sales)
Nayoung Kim nayoung.kim@hts.com Inside Sales
Nevin Wong nevin.wong@hts.com Branch Manager
Nicholas Pigeau nicholas.pigeau@hts.com Inside Sales
Nicholas Romano nicholas.romano@hts.com Inside Sales
Nick Pansuriya Other
Nick Sawatzky nick.sawatzky@hts.com Outside Sales
Nicole-Marie Sa'adeh nicole.marie.saadeh@hts.com Inside Sales
Nikolai Burton nikolai.burton@hts.com Inside Sales
Nima Johnson nima.jadidian@hts.com Inside Sales
Nirbhay Singh nirbhay.singh@hts.com Inside Sales
Noel Saldanha noel.saldanha@hts.com Outside Sales
Noemio Almeida noemio.almeida@hts.com Inside Sales
Patrick Jenie patrick.jenie@hts.com Inside Sales
Paul Naizer paul.naizer@hts.com Branch Manager
Paul Povolo paul.povolo@hts.com Outside Sales(Director-Engineering Sales)
Petr Shadrin petr.shadrin@hts.com Inside Sales
Phil Van Meppelen Scheppink phil.scheppink@hts.com Inside Sales
Phillip Leone phillip.leone@hts.com Inside Sales
Puneet Natt puneet.natt@hts.com Outside Sales
Raffaella Simone raffaella.simone@hts.com Other(Warranty Admin)
Rajeev Shah rajeev.shah@hts.com Inside Sales
Rajiv Chaddah rajiv.chaddah@hts.com Inside Sales
Randy Pooran randy.pooran@hts.com Inside Sales
Raymond Wong Other
Rea Patdo rea.patdo@hts.com Other(Accounts Payable)
Ricardo Ng ricardo.ng@hts.com Inside Sales
Rishi Mirchandani rishi.mirchandani@hts.com Principal
Rishi Singh rishi.singh@dxseng.com Other(Service Manager)
Rob Dean rob.dean@hts.com Outside Sales
Robert Skopyk robert.skopyk@hts.com Other(Team Leader-Parts and Aftermarket)
Rogan Uthayakumar rogan.uthayakumar@hts.com Other
Rohan Syal rohan.syal@hts.com Inside Sales
Roland Boucher roland.boucher@hts.com Admin
Ron Barber ron.barber@hts.com Outside Sales
Ross Willett ross.willett@hts.com Outside Sales(Operations Manager)
Ryan Hiscott ryan.hiscott@hts.com Outside Sales
Ryan Schleehahn ryan.schleehahn@hts.com Inside Sales
Sagar Prajapati sagar.prajapati@hts.com Other(Inside Sales)
Sal Gioia salvatore.gioia@hts.com Other
Salvatore Puma salvatore.puma@hts.com Outside Sales
Sara Harrison sara.harrison@hts.com Other(Parts)
Sasha Rampersad sasha.rampersad@hts.com Inside Sales
Sean Hua sean.hua@hts.com Inside Sales
Sean Newell sean.newell@hts.com Inside Sales
Sebastian Pal sebastian.pal@hts.com Inside Sales
Shaan Gill shaan.gill@hts.com Inside Sales
Shathurshan Umashanker shathurshan.umashanker@hts.com Outside Sales
Shawn Rohan Singh shawn.singh@hts.com Inside Sales
Shawn Umphrey Other
Shaza Mahayni shaza.mahayni@hts.com Inside Sales
Sheldon Ho sheldon.ho@hts.com Inside Sales
Siva Sigamani siva.sigamani@hts.com Outside Sales
Stephanie Leaper stephanie.leaper@hts.com Inside Sales
Stephanie McDonald stephanie.mcdonald@hts.com Inside Sales
Stephanie Uy stephanie.uy@hts.com Inside Sales
Steve Cukrovani steve.cukrovani@hts.com Outside Sales
Steve Davis steve.davis@hts.com Inside Sales
Steve Staromansky Other
Sue Eastwood sue.eastwood@hts.com Outside Sales
Sukhjinder Thind sukhjinder.thind@hts.com Outside Sales
Sung-ha Min sung-ha.min@hts.com Inside Sales
Sungmin Youn sungmin.youn@hts.com Inside Sales
Taha Jibril taha.jibril@hts.com Inside Sales
Tanner Vandervecht tanner.vandervecht@hts.com Outside Sales
Terry Loyala terry.loyala@hts.com Outside Sales
Tim Wilken tim.wilken@hts.com Controls
Tina Abbasi tina.abbasi@dxseng.com Inside Sales
Titus Robinson titus.robinson@hts.com Inside Sales
Tonie Ebora tonie.ebora@hts.com Inside Sales
Trisha Hough trisha.hough@hts.com Admin
Tyler Watson tyler.watson@hts.com Inside Sales
Vincent Le vincent.le@hts.com Inside Sales
Vithurshan Umashanker vithurshan.umashanker@hts.com Inside Sales
Vivienne Nguyen vivienne.nguyen@hts.com Inside Sales
Vladimir Golubin vladimir.golubin@hts.com Sales Support(Employee)
Wayne Freethy wayne.freethy@hts.com Outside Sales(Director-Engineering Sales)
Will Rea will.rea@hts.com Principal(Outside Sales)
Will Wolf will.wolf@hts.com Outside Sales
William Botic william.botic@hts.com Inside Sales
Wrai Sabatini wrai.sabatini@hts.com Outside Sales
Yara Eldin yara.eldin@hts.com Inside Sales
Yutaka Nohodomi yutaka.nohdomi@hts.com Inside Sales
Zohrab Soussani zohrab.soussani@hts.com Inside Sales
HTS Kitchener { Kitchener - 6020 }
Email: info_kitchener@hts.com
Phone Number: (519) 748-1860
Mailing Address: 110 Pinnacle Drive, Kitchener, Ontario N2P 1C5 Canada
Shipping Address: 110 Pinnacle Drive, Kitchener, Ontario N2P 1C5 Canada
Name Email Title
Amanda Graham amanda.graham@hts.com Outside Sales(Engineering Sales)
Andras Szucs andras.szucs@hts.com Inside Sales
Ariana Beepath ariana.beepath@hts.com Inside Sales
Christopher Koo christopher.koo@hts.com Inside Sales
Curtis Ballesteros curtis.ballesteros@hts.com Inside Sales
Daniel Silverberg daniel.silverberg@hts.com Inside Sales
Dave Scida david.scida@hts.com Principal
Davide Arcese davide.arcese@hts.com Inside Sales
Erin Smith erin.smith@hts.com Inside Sales
Evan Hatanaka evan.hatanaka@hts.com Inside Sales
Govind Sharma govind.sharma@hts.com Inside Sales
Graham Jones graham.jones@hts.com Principal
Hani Agha hani.agha@hts.com Inside Sales
Jay Irwin jay.irwin@hts.com Outside Sales
Justin Wright justin.wright@hts.com Inside Sales
Karl Wolf karl.wolf@hts.com Other
Kevin Leyte-Jammu kevin.leyte-jammu@hts.com Inside Sales
Lance HTS Other
Lucas Baranoski lucas.baranoski@hts.com Other
Nick Sawatzky nick.sawatzky@hts.com Outside Sales
Noah Ermers noah.ermers@hts.com Inside Sales
Peter Washer peter.washer@hts.com Outside Sales
Reece Buttenham reece.buttenham@hts.com Inside Sales
Rishi Mirchandani rishim@htseng.com Other(Contracting Sales Engr)
Ruban Batth ruban.batth@hts.com Inside Sales
Ryan Zavitz ryan.zavitz@hts.com Inside Sales
Sammy Juvatopolos sammy.juvatopolos@hts.com Inside Sales
Tarandeep Sian tarandeep.sian@hts.com Inside Sales
Terry Arcese terrya@htseng.com Other(Sales)
Tongyu Liu tongyu.liu@hts.com Inside Sales
Tyler Craig tyler.craig@hts.com Outside Sales
HTS London { London - 6060 }
Email: info_london@hts.com
Phone Number: (519) 457-6700
Mailing Address: 320 Neptune Crescent,Unit #6, London, Ontario N6M 1A1 Canada
Shipping Address: 320 Neptune Crescent,Unit #6, London, Ontario N6M 1A1 Canada
Name Email Title
Abdullah Barakat abdullah.barakat@hts.com Inside Sales
Alex Fortier alex.fortier@hts.com Inside Sales
Carly Dawe carly.dawe@hts.com Inside Sales
Hossam Khalil hossam.khalil@hts.com Inside Sales
Jeff Brode jeff.brode@hts.com Other(Parts)
Jeremy Sugimoto jeremy.sugimoto@hts.com Inside Sales
Jim Bender jim.bender@hts.com Outside Sales
Jonathan Sinden jonathan.sinden@hts.com Other(Account Executive)
Joseph Pongonthara joseph.pongonthara@hts.com Inside Sales
Justin Wright justin.wright@hts.com Inside Sales
Marco Rossi marco.rossi@hts.com Other
Marilyn Wang marilyn.wang@hts.com Other
Mark Vetero mark.vetero@hts.com Outside Sales
Mason Enemark-Mullie mason.enemarkmullie@hts.com Inside Sales
Randi Sayer randi.sayer@hts.com Estimator(Contracting Sales)
Ryan Claessens ryan.claessens@hts.com Outside Sales
Sawsan El Ayoubi sawsan.elayoubi@hts.com Outside Sales
Stephen Wong stephen.wong@hts.com Inside Sales
Terry Arcese terry.arcese@hts.com Branch Manager
Thomas Forsythe thomas.forsythe@hts.com Admin
Trevor Rideout trevor.rideout@hts.com Outside Sales
HTS Maine { Gray - 5870 }
Email:
Phone Number: (207) 657-7123
Mailing Address: P.O. Box 1375, Gray, Maine 04039-1375 United States
Shipping Address: 16 Northbrook Drive, Gray, Maine 04039-1375 United States
Name Email Title
Annmarie Juliano annmarie.juliano@hts.com Outside Sales
Ben Briggs ben.briggs@dxseng.com Outside Sales
Bruce Briggs bruce.briggs@hts.com Outside Sales
Greg Mylen greg.mylen@hts.com Principal
Mike Lovelette mike.lovelette@hts.com Outside Sales
Spencer Brown spencer.brown@hts.com Outside Sales
HTS New England { Boston - 6370 }
Email: lisa.hardwick@hts.com
Phone Number: (978) 977-9911
Mailing Address: One Corporation Way,Suite 110, Peabody, Massachusetts 01960 United States
Shipping Address: One Corporation Way,Suite 110, Peabody, Massachusetts 01960 United States
Name Email Title
Adam Camillo adam.camillo@hts.com Inside Sales
Alberto Carreno alberto.carreno@hts.com Inside Sales
Alex Clermont alex.clermont@dxseng.com Inside Sales
Allyson Lloyd allyson.lloyd@hts.com Inside Sales
Andrew Mark Mohn andrew.mark.mohn@hts.com Inside Sales
Andrew Williams andrew.williams@hts.com Inside Sales
Anthony Bedard anthony.bedard@hts.com Inside Sales
Ariana Axelrod ariana.axelrod@controltechinc.com Outside Sales
Arjun Ramanathan arjun.ramanathan@hts.com Inside Sales
Bailey Heald bailey.heald@hts.com Other(Service Technician)
Ben Almond ben.almond@hts.com Inside Sales
Bob Harrington bob.harrington@hts.com Outside Sales
Brenden Corbin brendan.corbin@dxseng.com Inside Sales
Brett Passemato brett.passemato@hts.com Outside Sales
Brian Keenan brian.keenan@hts.com Outside Sales
Brian Mills brian.mills@hts.com Inside Sales
Brian Williams brian.williams@hts.com Outside Sales
Brittany Vecchio brittany.vecchio@hts.com Other(Parts)
Brittany Vecchop brittany.vecchop@hts.com Inside Sales
Cameron Mariani cameron.mariani@hts.com Inside Sales
Chris Billings chris.billings@hts.com Inside Sales
Cole Gorham cole.gorham@hts.com Inside Sales
Corey Olson corey.olson@hts.com Inside Sales
Daniel Jenks dan.jenks@hts.com Outside Sales
Daniel Maille daniel.maille@hts.com Inside Sales
Daniel Senese dan.senese@hts.com Principal(Principal)
David Butcher david.butcher@hts.com Other(Sales Engineer)
David Ciampa david.ciampa@hts.com Other(Parts)
David Doherty david.doherty@hts.com Other
David Marcaccio david.marcaccio@hts.com Inside Sales
Dennis Hughes dennis.hughes@hts.com Outside Sales
Derek Anneser derek.anneser@hts.com Outside Sales
Edward Noyes edward.noyes@hts.com Outside Sales
Emery George emery.george@hts.com Principal(Principal)
Emma Collins emma.collins@hts.com Inside Sales
Eric Leighton eric.leighton@hts.com Inside Sales
Ethan Weisse ethan.weisse@hts.com Inside Sales
Gary Jensen gary.jensen@hts.com Other
Greg Mylen greg.mylen@hts.com Principal
Jack Husak jack.husak@hts.com Inside Sales
Jacob Brown jacob.brown@hts.com Outside Sales
Jacob Guss jacob.guss@hts.com Inside Sales
Jacob Stachowski jacob.stachowski@hts.com Other
James Leary james.leary@hts.com Inside Sales
James Murphy james.murphy@dxseng.com Inside Sales
Jeff Ritchie jeff.ritchie@hts.com Principal
Jeff Sartorelli jeff.sartorelli@hts.com Inside Sales
Jim Snyder jim.snyder@dxseng.com Inside Sales
John Bunn jonathan.bunn@hts.com Other(Service Technician)
Jon Czerepica jon.czerepica@hts.com Inside Sales
Jon Zuber jon.zuber@hts.com Outside Sales
Joseph Doyle joseph.doyle@hts.com Inside Sales
Joseph Tarantino joseph.tarantino@hts.com Outside Sales
Joseph Williams joseph.williams@hts.com Inside Sales
JS Rancourt js.rancourt@dxseng.com Principal
Justin Backe justin.backe@hts.com Other
Justin Thomaszewski justin.thomaszewski@hts.com Inside Sales
Kevin Ng kevin.ng@hts.com Inside Sales
Kevin Tolson kevin.tolson@hts.com Other(Sales Engineer)
Larry Canto laney.canto@hts.com Outside Sales
Lily Nardelli lilly.nardelli@dxseng.com Outside Sales
Lisa Hardwick lisa.hardwick@hts.com Admin
Luke Cava luke.cava@hts.com Inside Sales
Mackenzie Poirier mackenzie.poirier@hts.com Outside Sales
Madysen Wallace madysen.wallace@hts.com Inside Sales
Margaret Busteed margaret.busteed@hts.com Admin
Mark Brazell mark.brazell@hts.com Inside Sales
Mark LaFrance mark.lafrance@hts.com Principal(Principal)
Nicholas Walsh nicholas.walsh@hts.com Office Manager
Nick Andrade nick.andrade@hts.com Inside Sales
Nick Dariotis nick.dariotis@dxseng.com Inside Sales
Nick Madsen nick.madsen@dxseng.com Other(Sales Assistant)
Paul Bodvar paul.bodvar@hts.com Other(Outside Parts Sales Mgr)
Paul Fleury paul.fleury@hts.com Inside Sales
Paul Kaschak paul.kaschak@hts.com Other(Sales Engineer)
Paul Santos pauls@ssservicecorp.com Other
Peter Allan peter.allan@hts.com Other
Peter Foss peter.foss@hts.com Principal(Principal)
Peter Raei peter.raei@hts.com Inside Sales
Peter Ripley peter.ripley@hts.com Outside Sales
Robert Ciampa robert.ciampa@dxseng.com Inside Sales
Robert Jones robert.jones@hts.com Other(Sales Engineer)
Sal Gioia salvatore.gioia@hts.com Other
Samantha Zisa samantha.zisa@hts.com Inside Sales
Sebastian Murzyn sebastian.murzyn@hts.com Inside Sales
Taylor Peterson taylor.peterson@hts.com Outside Sales
Tim McClure tim.mcclure@hts.com Other(Parts Outside Sales)
Titus Robinson titus.robinson@hts.com Inside Sales
TJ McLaughlin tj.mclaughlin@hts.com Other(Service)
Tommy Ciolfi tommy.ciolfi@dxseng.com Inside Sales
Trevor Jones trevor.jones@hts.com Other(Sales Engineer)
William McGinley william.mcginley@hts.com Inside Sales
William Zavodjancik william.zavodjancik@hts.com Inside Sales
Willie Dawkins willie.dawkins@hts.com Other(Sales Engineer)
Zach Ball zach.ball@hts.com Other(Sales Manager)
Zach Bogle zach.bogle@hts.com Inside Sales
Zachary Girard zachary.girard@hts.com Other
HTS Texas { Austin - 5920 }
Email: texas@hts.com
Phone Number: (512) 381-0091
Mailing Address: 6101 West Courtyard Drive,Bldg 4, Austin, Texas 78730 United States
Shipping Address: 6101 West Courtyard Drive,Bldg 4, Austin, Texas 78730 United States
Name Email Title
Angel Cazares angel.cazares@hts.com Other(Service Technician)
Ankur Patel ankur.patel@hts.com Other
Ashley Heisler ashley.heisler@hts.com Principal
Austen Holley austen.holley@hts.com Inside Sales
Blair Howell blair.howell@hts.com Other
Brad Boutwell brad.boutwell@hts.com Inside Sales
Brandon Landry brandon.landry@hts.com Inside Sales
Brandon Tarnow brandon.tarnow@hts.com Other
Brian Tarnow Other
Chris Ford chris.ford@hts.com Inside Sales
Chris Revering chris.revering@hts.com Other(Service)
Chris Richardson chris.richardson@dxseng.com Outside Sales
Chris Taylor chris.taylor@hts.com Other
Clayton Nevill clayton.nevill@hts.com Other(Intern)
Cody Wisenbaker cody.wisenbaker@hts.com Outside Sales
Colton Mitchell colton.mitchell@dxseng.com Inside Sales
Dane Short dane.short@hts.com Outside Sales
Danny Wuthrich Other
Dean Revering dean.revering@hts.com Outside Sales
Drew Higgins drew.higgins@hts.com Outside Sales
Erin Crow erin.crow@dxseng.com Other(Project Manager)
Erin Crow erin.crow@hts.com Inside Sales
Evan Chapman evan.chapman@hts.com Outside Sales
Grayson Story grayson.story@hts.com Inside Sales
Jake Reed jake.reed@hts.com Outside Sales
James Beals james.beals@hts.com Other
Jason Hieatt jason.hieatt@dxseng.com Outside Sales
Jeff Flick jeff.flick@hts.com Other
Jerome Caulkin Other
Joe Kratch joe.kratch@hts.com Inside Sales
John Vlcek Other
Kareem Alawar kareem.alawar@hts.com Outside Sales
Kathleen Leyendecker kathleen.leyendecker@dxseng.com Inside Sales
Katie Klassen katie.klassen@hts.com Outside Sales
Keith McLaughlin keith.mclaughlin@dxseng.com Principal
Kyle Kramer kyle.kramer@hts.com Principal
Lincoln Lynch lincoln.lynch@hts.com Other
Lucas Revering lucas.revering@hts.com Inside Sales
Madeline Zidar madeline.zidar@dxseng.com Inside Sales
Micah Andress micah.andress@hts.com Other
Michelle Waterhouse michelle.waterhouse@hts.com Other
Mike Hatt michael.hatt@hts.com Other
Mitchell Mesenbrink mitchell.mesenbrink@dxseng.com Outside Sales
Paige McKenzie paige.mckenzie@dxseng.com Inside Sales
Paul Moubarak paul.moubarak@hts.com Inside Sales
Peter Cornell peter.cornell@hts.com Inside Sales
Rachel Ramirez rachel.ramirez@hts.com Admin
Rich Neitzke rich.neitzke@hts.com Inside Sales
Richard Coastal coastalmech01@gmail.com Other
Roger Stuksa roger.stuksa@hts.com Other
Ross Wojcik ross.wojcik@hts.com Outside Sales
Ryan Boatright ryan.boatright@hts.com Inside Sales
Sean Fanning sean.fanning@hts.com Inside Sales
Steve Kreitzer steve.kreitzer@hts.com Inside Sales
Steven Kroleski steven.kroleski@hts.com Inside Sales
Thomas McLaughlin thomas.mclaughlin@dxseng.com Principal
Travis Schlageter travis.schlageter@hts.com Inside Sales
Trey Campsmith trey.campsmith@hts.com Inside Sales
Tucker Niesner tucker.niesner@hts.com Outside Sales
Tyler Hughes tyler.hughes@hts.com Other(Service Tech)
HTS Texas { Dallas - 5930 }
Email: texas@hts.com
Phone Number: (866) 544-1487
Mailing Address: 1625 Wallace Drive,Suite 120, Carrollton, Texas 75006 United States
Shipping Address: 1625 Wallace Drive,Suite 120, Carrollton, Texas 75006 United States
Name Email Title
Aaron Bartek aaron.bartek@hts.com Outside Sales
Adam Kuskos adam.kuskos@hts.com Outside Sales
AJ Philips Other(Service Tech)
Alberto Garcia alberto.garcia@hts.com Other
Alex Berend alex.berend@hts.com Outside Sales
Arlesha Henderson nikki.henderson@hts.com Inside Sales
Ashley Fiddelke ashley.fiddelke@hts.com Outside Sales
Bobby Dodd bobby.dodd@hts.com Outside Sales
Brandon Damas Other
Brandon Damas brandon.damas@hts.com Outside Sales
Charmaine Gill charmaine.gill@dxseng.com Inside Sales
Chris Jung chris.jung@hts.com Inside Sales
Chris King chris.king@hts.com Outside Sales
Chris Stokes chris.stokes@hts.com Inside Sales
Clarissa Escobar clarissa.escobar@hts.com Inside Sales
Curtis Williams curtis.williams@hts.com Other
Dalton Posehn dalton.posehn@hts.com Inside Sales
Dan Torres dan.torres@hts.com Outside Sales
Eric Lam eric.lam@hts.com Inside Sales
Erin Hollingsworth erin.hollingsworth@hts.com Inside Sales
Greg Wurm greg.wurm@hts.com Other
Henry O'Connor henry.oconnor@hts.com Outside Sales
Hunter Sparks hunter.sparks@hts.com Inside Sales
Ian Owerbach ian.owerbach@hts.com Other